Fuel Conversion Kit Instruction Guide

ManualsBrandsNapoleon ManualsAccessoriesNatural Gas to Propane Conversion Kit for Vector 62 Series Fireplace

LV38-1 illustrated.

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts speciﬁcally

approved with this appliance may result in property damage or personal injury.

CAUTION: Before proceeding with conversion the gas supply must be shut off prior to disconnecting the electrical power.

1. Remove the safety barrier, door trim and glass door. Remove existing media and media trays. Set aside.

2. Disengage the air shutter adjustment rod by pushing the smaller end of the rod to the left then push towards the back of

the appliance until the rod clears the rubber grommet (Fig. 1). The rubber grommet must stay in place.

3. Remove the screws that secure the entire burner assembly in place (screw counts vary by appliance size) (Fig. 2). Lift the

entire burner assembly up and out of the appliance. Remove the air shutter adjustment rod. Set both aside.

4. Using a deep socket wrench, remove the oriﬁce from within the ﬁrebox and replace with the oriﬁce supplied.

5. Remove the two screws from the valve regulator and remove the regulator, replace with the one supplied (Fig. 2).

6. Remove the pilot spring clip then the pilot hood from the pilot assembly by pulling vertically. Use a

” Allen key to

unscrew the injector. Replace the pilot injector with the one supplied (Fig. 3). Re-assemble the pilot hood onto the

assembly and reattach the spring clip ensuring key position for proper alignment.

This conversion kit shall be installed by a qualiﬁed service agency in accordance with the manufacturer’s instructions

and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions

is not followed exactly, a ﬁre, explosion or production of carbon monoxide may result causing property damage,

personal injury or loss of life. The qualiﬁed service agency is responsible for the proper installation of this kit. The

installation is not proper and complete until the operation of the converted appliance is checked as speciﬁed in the

owner instructions supplied with the kit.

FUEL CONVERSION KITS FOR MODELS LV38-1 / LV50-2 / LV62

These kits are for use at altitudes of 0 to 4,500 feet.

INSTALLER: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOME OWNER.

CHECK THE BOXES TO INDICATE THAT THE CORRESPONDING STEPS HAVE BEEN COMPLETED.

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 0G8 Canada • 1(866)820-8686 • www.napoleonreplaces.com

W415-1782 / B / 09.28.17

Figure 1

We strongly recommend converting your appliance prior to ﬁnal installation and removing porcelain panels for conversion.

important:

Kit W175-0642, Natural Gas to Propane Includes;

1 Regulator

1 #53 Burner oriﬁce

1 Propane burner tube

LV38-1

Kit W175-0644, Natural Gas to Propane Includes;

1 Regulator

1 #52 Burner oriﬁce

1 Propane burner tube

LV50-2

Kit W175-0646, Natural Gas to Propane Includes;

1 Regulator

1 #51 Burner oriﬁce

1 Propane burner tube

LV62

1 Propane pilot injector

1 Conversion data label

1 Air shutter adjustment rod

1 Propane pilot injector

1 Conversion data label

1 Air shutter adjustment rod

1 Propane pilot injector

1 Conversion data label

1 Air shutter adjustment rod

Figure 2

Summary of content (10 pages)

PAGE 1
INSTALLER: THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOME OWNER. CHECK THE BOXES TO INDICATE THAT THE CORRESPONDING STEPS HAVE BEEN COMPLETED. FUEL CONVERSION KITS FOR MODELS LV38-1 / LV50-2 / LV62 These kits are for use at altitudes of 0 to 4,500 feet.
PAGE 2
Figure 3 Figure 5 Figure 4 PILOT HOOD PILOT INJECTOR Indicator label SPRING CLIP 7. Install the new air shutter adjustment rod (supplied) by sliding the smaller end through the rubber grommet from the inside of the firebox. The rubber grommet must be seated correctly in order to properly seal the appliance. 8. Remove screws securing the old burner tube to the burner assembly (screw count varies by size of appliance) (Fig. 4). 9.
PAGE 3
WARNING: AIR SHUTTER ADJUSTMENT MUST BE DONE BY A QUALIFIED INSTALLER. Closing the air shutter will cause a more yellow flame, but can lead to carboning. Opening the air shutter will cause a more blue flame, but can cause flame lifting from the burner ports. The flame may not appear yellow immediately; allow 15 to 30 minutes for the final flame colour to be established. CLOSE OPEN AIR SHUTTER ADJUSTMENT PRESSURE ADJUSTMENT Adjust the pilot screw to provide properly sized flame.
PAGE 4
LV38-1 venting configurations (P) V+H ≤ 40 ft. H ≤ 10 ft. (For longer vent runs, a power vent is required). V + H are measured from the centre of vent elbows. Elbows are considered as 90º. Two 45º elbows = One 90º elbow. For 0 elbow configurations, V is a minimum of 6’ to a maximum of 40’. 40’ 38 1/2’ (462”) 30’ 1-4 elbow zone 1-3 elbow zone 1-2 elbow zone 1 elbow zone V 20’ 15’ Refer to appliance specific GPV/PVA instructions for other venting configurations.
PAGE 5
LV50-2 / LV62 venting configurations (P) 40’ V+H ≤ 40 ft. H ≤ 4⅜ ft. (For longer vent runs, a power vent is required). V + H are measured from the centre of vent elbows. Elbows are considered as 90º. Two 45º elbows = One 90º elbow. For 0 elbow configurations, V is a minimum of 6’ to a maximum of 40’. 38 ½’ (462”) 35’ 30’ 1-2 elbow zone 1 elbow zone V 20’ 15’ Refer to appliance specific GPV/PVA instructions for other venting configurations.
PAGE 6
INSTALLATEUR: CES INSTRUCTIONS DOIVENT ÊTRE GARDÉES PAR LE PROPRIÉTAIRE. VEUILLEZ COCHER LES CASES POUR INDIQUER QUE LES ÉTAPES CORRESPONDANTES ONT ÉTÉ COMPLÉTÉES. ENSEMBLE DE CONVERSION POUR LES MODÈLES LV38-1 / LV50-2 / LV62 Cet ensemble est utilisé pour des altitudes de 0 à 4 500 pieds.
PAGE 7
Figure 3 Figure 5 Figure 4 HOTTE DE DÉRIVATION DE FLAMME INJECTEUR DE VEILLEUSE PINCE À RESSORT Plaque d’indication 7. Installez la nouvelle tige de contrôle (fourni) par glissez la côté la plus petit à travers le passe-câble en caoutchouc par l’intérieur du chambre de combustion. Le passe-câble en caoutchouc doit être bien placer afin d’assurer que l’appareil est scellé correctement. 8.
PAGE 8
AVERTISSEMENT: LE RÉGLAGE DU VOLET D’AIR DOIT ÊTRE EXÉCUTÉ PAR UN TECHNICIEN OU INSTALLEUR QUALIFIÉ Plus le volet est fermé, plus la flamme est jaune et plus elle aura tendance à causer des dépôts de carbone. Plus le volet est ouvert, plus la flamme est bleue et plus elle a tendance à se détacher des orifices du brûleur. La flamme peut ne pas être jaune immédiatement; allouez de 15 à 30 minutes pour que la couleur finale de la flamme se stabilise.
PAGE 9
Configurations d’évacuation LV38-1 (P) V+H ≤ 40 pi. H ≤ 10 pi. (Pour les courses horizontales longueurs, un terminaison mécanique est requis). V + H sont mesurés du centre à partir du centre centre des coudes d’évents. Les coudes sont considérés comme 90º. Deux coudes de 45º = Une coude de 90º. Pour les configurations avec zéro coude, V est un minimum de 6 pi à un maximum de 40 pi.
PAGE 10
Configurations d’évacuation LV50-2 / LV62 (P) 40’ V+H ≤ 40 pi. H ≤ 4⅜ pi. (Pour les courses horizontales longueurs, un terminaison mécanique est requis). V + H sont mesurés du centre à partir du centre centre des coudes d’évents. Les coudes sont considérés comme 90º. Deux coudes de 45º = Une coude de 90º. Pour les configurations avec zéro coude, V est un minimum de 6 pi à un maximum de 40 pi.