T10 Narwal Robot Mop & Vacuum with Self-Cleaning Station User Manual Please read this product manual carefully before use and keep it properly. Due to continuous product renewal, please refer to the actual product.
Dear customer: Thank you for choosing Narwal Robot Mop & Vacuum, we are committed to providing you with hands-free cleaning experience. If you have any question, please contact: support@narwalrobotics.com For more details, please visit Narwal official website: www.narwalrobotics.com Wish you a happy experience of using Narwal. Yunjing Intelligence Technology (Dongguan) Co., Ltd. Room 508, Unit 1, Building 17, No.
Precautions This product is only used for floor cleaning in the home environment. Do not use it outdoors (such as open balcony), non-ground (such as sofa, window sill), elevated surface, commercial or industrial environment. 1 Do not use it in an elevated surface (such duplex floor or the top of furniture) without the barriers. 2 Do not place any objects (including humans and pets) on stationary or moving robots. 3 Do not put your hair, fingers, etc.
Precautions 4 Do not let the robot inhale hard or sharp objects. 5 Do not place the robot near heat and water sources (eg radiators and faucets). 6 Please use the following methods to move the robot if needed.
Warning 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. This product is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervisor instruction concerning use of the product by a person responsible for their safety. Children should be supervised to ensure that they do not play with the product.
Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
1. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. 2. The operating temperature of the EUT can’t exceed 40℃ and shouldn’t be lower than 5℃ . Hereby, Yunjing Intelligence Technology (Dongguan) Co., Ltd. declares that this product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU. This product is allowed to be used in all EU member states.
Table of content Introduction What's in the box About the robot & base station 01 02 Installation Base station installation Robot preparation 12 13 How to use Narwal Tips Basic operation Mapping Vacuum/Mop Cleaning path 14 16 18 19 20 Maintenance Robot Base station Accessories 22 26 30 Trouble shooting 33 Specifications 39 Warranty policy 40
What's in the box Robot x1 Mopping module x2 Base station x1 Mop x4 Sweeping module x1 Magnetic strip x1 Power cord x1 Side brush x2 Detergent x1 Bird knife x1 Filter sponge x2 01
About the robot & base station Reset button • Press and hold for 3 seconds to reset Power button • Press and hold for 2 seconds to turn on/off Start button • Short press to start/pause cleaning • Press and hold for 2 seconds to stop current task Circular indicator light • White —— standby • Purple —— working • Purple blink —— paused • Red blink —— malfunction Note: 1. Find the bird knife at the highlighted (blue) area. 2.
Filter Filter buckle Dust bin buckle Dust bin handle 03
About the robot Market Model: YJCC002-R Bumper Cliff sensor Omni-directional wheel Sweeping module mounting port Mopping module mounting shaft Suction inlet Main wheel Lidar 04 Battery
Bumper Speaker Air vent Wall sensor Obstacle avoidance sensor Charging electrode 05
Base station Market Model: YJCC002-B Power outlet Sewage tank inlet Pumping port Air inlet Clean water tank outlet Charging electrode Clean water spout Guide pulley Overflow sensor Sewage pumping port Air vent Washboard 06
Sewage tank float Water tank handle Water tank buckle Cover lid Sewage tank cover Sewage tank buckle Water inlet Clean water tank cover Clean water tank Sewage tank Filter sponge 07
Base station panel Base station screen & buttons OLED screen Home button • Short press to command the robot to return/exit the base station. • Press and hold for 2 seconds to reset the map and start mapping.
Screen icon Sweeping icon Indicates the current status is vacuuming. Charging icon Indicates that the robot and base station charging electrodes are connected successfully. Narwal icon Indicates that the base station/robot has been turned on/off Mopping icon Indicates the current status is mopping. Battery icon Indicates the current battery level. Child lock icon Indicates that the current base station panel is locked.
Cleaning modules Sweeping module Module lid Side brush 10 Suction inlet Mounting magnet Sweeping module mounting shaft
Mopping module Handle Mop velcro Mop Mopping module mounting port 11
Base station installation 1. Power-on 2.Base Station placement Connect the power cord to the back socket of the base station, plug it into the power outlet. Note: please fasten the power cord to avoid poor connection. Keep the base station on a flat surface, against a wall. Note: ensure to leave enough space to the charging station (0.5 meters on both sides, more than 1.5 meters in the front) 5m .,0.3 3 0. .,5m m .
Robot preparation 1. Turn on Press and hold the power button for 2 seconds to turn on the robot. Note: do not move the robot when it is starting. It can not be turned on when the battery is low. lease put the robot into the base station to charge. 2. Install & remove the sweeping module 3. Install & remove the mopping module Insert the protrusions under the sweeping module into the slot and press the sweeping module. The robot will automatically hold the module.
How to use Narwal tips 1. Please put away all wires on the ground (including the power cord of the base station) before using the robot to avoid any malfunction of the robot or damage of your belongings. 14 2. Do not move the base station after mapping, it will cause the robot fails to return to the base station. It has to rebuild the map after moving the base station. 3. Do not move the washboard when the robot is working, otherwise, the robot will not wash the mops.
4. The robot can go across the obstacles less than 1.5cm in height. 5. Please place the magnetic strip at the around areas you do not wish to clean before the robot starts to work. Magnetic strip 1.
Basic operation Robot basic operation Power on/off • Press and hold the power button for 2 seconds to turn on/off Start task • Short press the start button to start a new task. Pause/resume task • Short press the start button to pause/resume. End current task • Press and hold the start button current task and stand by. for 2 seconds to end the Factory reset • Press and hold the reset button for 3 seconds to reset the robot. Reset Wi-Fi • Press and hold power button seconds to reset Wi-Fi.
Base station operation Send home/exit base station • Short press the home button return/exit the base station. Start task • Short press the start button Pause/resume task • Short press the start button End current task • Press and hold the start button the current task and stand by. to command the robot to start a new task. to pause/resume.
Mapping 1. Long press the home button on the base station to start the mapping. 2. The robot scans all rooms along the contour of the room to create a map of the entire house. 3. After mapping, the robot will return to the base station for room division and charging. Note: 1. The robot needs to install the sweeping module for mapping. 2. The robot must be in the base station before mapping starts. 3.
Vacuuming Mopping 1. Install the sweeping module. 2. Short press the start button on the base station or on the robot to start vacuuming. 3. After vacuuming, the robot will automatically return to the base station for charging. 1. Install the mopping module. 2. Short press the start button on base station or robot to start mopping. 3. During mopping, the robot will automatically return to the base station to wash the mop to keep it clean. 4.
Cleaning path Vacuuming path Mopping path 2 1 3 The robot will clean from the room of base station for vacuuming by default. 20 2 3 1 To avoid secondary contamination, the robot will clean from the farthest room for mopping by default.
