User's Manual
National Electronics & Watch Co, Ltd.
BC10
• Press S3 to set the Low/High limit of the zone. You can still manually change the value by
pressing S1/ S5.
• Press S3 to the Zone Alarm ON or OFF. Press S1 or S5 to change setting.
• Press S7 to exit.
TIMER mode
Setting the TIMER:
Press and hold S11 until the Timer “1” digit starts to blink. Press S1/S5 to select the interval
timer “SEG 1 to 6”. Press S3 to set the hour, minute & second. Press S1/S5 to increase or
decrease the value. Press S7 to exit setting.
Note: If there is no key operation within 3-4 minutes in this mode, the watch will auto exit to
Time mode.
ALARM mode
Setting the ALARM:
Press S7 from TIMER mode to enter ALARM mode. The watch will display the alarm view.
Press and hold S11 until the Alarm “1” digit starts to blink. Press S1/S5 to select the Alarm 1
to 5. Press S3 to set the hour, minute, Time, Alarm and Chime.
For Chime, press S1/S5 to turn it ON or OFF. Also note when Chime is ON, the Key tone is
automatically ON and the Chime icon appears in all modes. Likewise, if Chime is OFF the
Key tone is automatically OFF.
Alarm setting in SET mode:
• Select ALARM then press S3
• Select ALARM 1 to ALARM 5 by pressing S1/S5 and then press S3 to enter.
• Set the HOUR. Press S1/S5 to change values. Press S3 to enter
• Set the MINUTE. Press S1/S5 to change values. Press S3 to enter
• Set the alarm time referred to T1 or T2. Press S1/S5 to change. Press S3 to enter
• Set the alarm ON or OFF. Press S1/S5 to change. Press S3 to enter
• Set the Chime ON or OFF. Press S1/S5 to change. Press S3 to enter
• Press S7 to exit alarm setting
SET mode
Press S7 from ALARM mode to SET mode. 1.5 seconds later the watch will display the
setting options: Press S5 the ff. Sequence are as follows; AUTO LAP, TIME, UNIT, USER,
HRM, HRM LINK, NIGHT, CONTRAST, CHIME, ALARM and TIMER. Press S3 to enter
selected option to set. Press S1/S5 to select then press S3 to enter. Press S7 to exit setting to
Time mode.
Setting the Auto Lap:
The same setting procedure applies in setting the time in Alarm setting mode.
Note: Alert sub-mode, press S3 to enter ALERT function. When alert is set to ON, there will
be a beep sound during taking auto lap. When it is set to OFF, there is no beep sound.
SETTING THE TIME:
TIME 1 setting:
You have two options in setting the watch, GPS or MANUAL. In manual setting, you can
manually set the time. If you select the GPS option, the watch will be automatically set
based on the data and time data from GPS satellites.
• Select TIME by pressing S1/S5 and then press S3 to enter.
• Select GPS or MANUAL setting by pressing S1/S5 and then press S3 to enter.
GPS setting:
¾ Select TIME ZONE by pressing S1/S5 and press S3 to enter.
¾ Select DST ON or OFF by pressing S1/S5 and press S3 to enter.
¾ Select 12H/ 24H format setting by pressing S1/S5. Press S3 to enter.
¾ Select M-D/ D-M format by pressing S1/S5 and press S3 to enter.
¾ The watch will go back to Time.
MANUAL setting:
¾ Set the HOUR by pressing S3 and press S1/S5 to change digit then press S3 to enter.
¾ Set the MIN by pressing S3 and press S1/S5 to change digit then press S3 to enter.
¾ Set the SEC by pressing S3 and press S1/S5 to change digit then press S3 to enter.
¾ Set the YEAR by pressing S3 and press S1/S5 to change digit then press S3 to enter.
¾ Set the MONTH by pressing S3 & press S1/S5 to change digit then press S3 to enter.
¾ Set the DATE by pressing S3 and press S1/S5 to change digit then press S3 to enter.
¾ Set the 12/24H by pressing S3 and press S1/S5 to change digit then press S3 to enter.
¾ Set the M-D/ D-M format by pressing S1/S5 to change the press S3 to enter.
¾ The watch will go back to Time.
TIME 2 setting:
You have two options in setting the watch, AUTO or MANUAL. In manual setting, you can
manually set the time. If you select the AUTO option, the watch will be automatically set
base on the data and time data from GPS satellites.
The procedure in setting time 2 is the same with time 1 setting.
Setting the UNIT:
Press S3 to enter. Press S1/S5 to select KM or Mi.
Setting the User’s information:
Press S3 when the USER option is highlighted. The sequence of setting is as follows: Gender
Æ Age Æ Weight Æ Height Press S1 or S5 to change values. Press S3 to set next parameter.
Press S7 to exit.