User's Manual

National Electronics & Watch Co, Ltd.
BC10
Setting the HRM:
Press S3 to enter. Press S1/S5 to select HRM zones. Then press S3 again to set Low and
High limit of the zone. Press S1/S5 to manually change the value. Press S3 to confirm setting.
Press S7 to exit setting.
Note: User has also an option to ON or OFF the zone Alarm.
HRM LINK:
Press S3 to enter. The watch will auto link and will display the Heart rate. Press S7 to exit.
Setting the DISPLAY (LCD contrast):
Press S3 to enter. Press S1 or S5 to change the setting. Press S3 to confirm setting and exit.
Setting the Chime:
Press S3 to enter. Press S1 or S5 to select ON or OFF.
Setting ALARM:
The same procedure applies in setting the Time.
Setting TIMER:
Press S3 to enter. Press S1 or S5 to select the Timer “SG 1 to 6”. Press S3 to set next
parameter. Press S7 to exit.
Setting the NIGHT mode:
Press S3 to enter. Press S1/S5 to select the following options: Night ON, 10 sec and 20 sec.
10 SECONDS – Press S11 will turn ON the Light for 10 seconds.
20 SECONDS – Press S11 will turn ON the Light for 20 seconds.
NIGHT ON – Light will continuously ON when CHRONO is running from 6:00 pm to 7:00 am.
But when CHRONO is stopped or reset from 6:00 pm to 7:00 am, press any key can turn ON
the light for about 10 seconds.
Press S3 to accept the selected setting. Press S7 to exit.
Battery:
Watch is using a rechargeable Lithium Ion battery that will require about 4.0 hours charging
time using the USB cable. While battery is charging, the watch cannot be used and all buttons
are disabled. User needs to recharge the battery when the watch indicates a “low battery”.
Note:
Battery Life (fully charge battery); 8 hrs minimum with GPS ON, CHRONO ON and HRM ON in
day time within the time period from 7 am to 6 pm.
While approx. 7 hours with GPS ON, CHRONO ON, HRM ON and Light ON within the time
period from 6 pm to 7 am. This means, after 7 or 8 hours continues activity such as running,
walking, etc., the battery power become low and the watch will display “LOW BATT”.
GPS watch troubleshooting guide:
PROBLEM
/
QUESTION SOLUTION/ ANSWER
How to turn off the GPS
Press and hold S9 for about 5 seconds from any view to
turn OFF the GPS.
I cannot get a GPS signal
Take your GPS watch outdoors and away from tress and
tall buildings. Remain stationary and try acquiring GPS
signal again. Be sure that the antenna is pointing towards
the sky for better signal reception.
Can I reset the watch?
You can reset the watch by pressing S1, S5, S7, and S11
together. The date and time will be reset to default
values. You can set it again manually or automatically thru
GPS.
Will my data and personal
settings be lost after watch
reset?
Your data and personal settings are saved in the flash
memory and will not be lost after watch reset.
The battery indicator does
not seem to be accurate
Allow your GPS watch to fully discharge and then fully
charge it without interruption. It is recommended to
regularly re-charge your battery every 1-2 months even if
it is not used to maintain good battery condition.
My heart rate data seems
inaccurate.
- Make sure the HR belt is snugly fit to your body
- Reapply water or electrode gel to the electrode of the
HR belt
- Clean the electrodes from possible contamination that
may interfere with heart rate signals
- Wear a cotton shirt or if possible, wet your cotton shirt.
Synthetic fabrics that rubs with your skin may create
static electricity and interfere with the heart rate signal
- Move away from strong electromagnetic fields and other
wireless sensors which can interfere with your heart rate
sensor. Possible sources of wireless interference may
include high voltage power lines, electric motors,
microwave ovens, cordless phones, and wireless LAN
or access points.