Installation & Assembly

Assembly Instructions
for NPSC 6200/6300/6400 stool series
Backrest & Adjustable Height models.
ADJUSTABLE HEIGHT
LEG ASSEMBLY
Mailing Address: 149 Entin Road, Clif
ton NJ 07014
| T
el 973-594-1100 | Fax 973-594-1500
Pl
ants in | Clifton, NJ 07014 | Memphis, TN 38106 | Chino, CA 91710
P
arts:
4
x Chrome plated adjustable height legs.
4 x Screws for adjustable legs
Turn stool upside down on a flat sturdy surface.
Gently pry the plastic glides off the bottom of each
leg.
Insert an “adjustable height leg” into a fixed leg.
Line up a hole on the “adjustable height leg” with
the hole on the fixed leg at the desired height.
T
ools needed:
P
hilips Head Screwdriver
Drive the supplied screw thru both holes & tighten
securely.
Repeat on remaining legs (be sure to align all legs
a
t the same height).
Adjustments to the height can be done by turning the
stool upside down, removing the screws & following
the above instructions from point 4.
BACKREST INSTALLATION
Turn stool upside down onto an elevated flat
sturdy surface.
Identify the four center holes closest to the X
(where the legs cross).
Place the “mounting plate” - flat side down - on
the point where the bars cross.
Align the four holes on the “mounting plate” with
the four holes mentioned above.
Drive supplied screws thru “mounting plate” into
crossbars.
Tighten securely.
Use the supplied “Alan wrench” to loosen the
black screw located on top of mounting plate.
Insert the shorter –blank end-of the backrest
“arm” into the opening of the “mounting plate”
with the ind
entation of the arm aligned with the
black screw. Use the “Alan wrench” to tighten the
black screw.
Screw the supplied “knob” into the threaded hole
in the center of the “mounting plate” and tighten
securely at the desired horizontal location.
Turn the stool back to its upright position.
Slide the “backrest” on to the backrest “arm”, so
that the slot on the “backrest” aligns with the
threaded hole in the top edge of the backrest
“arm”.
Drive the supplied “bolt & washer” thru the slot of
the “backrest” & into the threaded hole on the
backrest “arm”.
Tighten securely at the desired height.
Adjustments can be easily made by loosening the
backrest bolt or mounti
n
g plate knob then adjusti
n
g
& tightening the bolt or knob at the new desired
position.
Parts: 1 x Mounting plate
4 x Screws for mounting plate
1 x Plastic knob
1 x Backrest Arm
1 x Backrest
1 x Bolt & Washer for backrest
Tools needed: Philips Head Screwdriver
Pliers
13-32 Ratchet Driver
Note: Some screws & bolts may be slightly difficult to drive initially. In this case some extra force is
necessary. Since the screws are self-threading, this will rethread the tubing where necessary.
Dear Customer,
Thank you for your purchase. Although extreme care goes into manufacturing & packaging of this product,
mistakes are possible. If you encounter any missing parts or difficulty in assembly, etc. please call our customer
service
TOLL FREE at 1-800-261-4112 for courteous & immediate resolution to your problem.
CAUTION!
Doub
le check all scre
ws to be tightened securely
bef
ore use.
Check all scre
ws periodically
.
Failure to completely tighten the screws may result
in tipping & p
ossib
le injury!
6224HB
6324HB
6418HB
6224H
6
418
11/7/06

Summary of content (1 pages)