Instructions / Assembly

Each carton contains one top section, one
b
ottom section (larger trees include one or
more middle sections) and a tree stand.
1. Unfold the tree stand and insert the eye
bolt. Remove packing material from ends
of poles. Put bottom section pole into tree
stand making sure it is seated properly
(Figure 1). Tighten eye bolt until bottom
section is held securely.
2. Insert the top tree section into the green
plastic opening of the lower tree assembly.
This is the “pole cap” which keeps tree top
s
ection securely in place (Figure 2).
P
owerConnect® trees will not have a pole
cap. Center pole of top section simply
inserts into center pole of section below.
For larger trees with middle section,
carefully insert middle section pole(s) into
bottom section pole (Figure 3) as
instructed in SPECIAL NOTE ABOUT
GIANT TREES below. Then insert top
section into pole cap. Optional: You may
want to lubricate middle section pole ends
prior to assembly. This will make sections
easier to separate when disassembling for
storage.
3. (Figure 4) Each tree section has a light
string cord that will plug into a receptacle
on the section below. Note that the male
and female connectors are
keyed and will only connect
in one direction. After
connection, twist closed each
connector nut securely.
GIANT TREES that include
additional sections will also
have additional light string
cord connections.
4. SHAPING: Branches should
fall into place during
assembly. If any branches
remain upright, gently lower
them into proper position
(Figure 5). See IMPORTANT
NOTE below.
Each branch must be shaped
to a natural position by
spreading out the tips. Please
follow Shaping Instructions
on next page for proper
shaping technique.
MEMORY SHAPE
®
TREES do
not require branch shaping.
Branches should fall into
place during assembly. If any
branches remain upright,
gently lower them into proper
position.
Fig. 4
Important Note: When lowering branches be ex-
tremely careful not to tangle wire in gap between
branch and bracket.
Not all low voltage trees
include foot switch
Low Voltage LED Trees
3
Low Voltage LED Bulb Replacement Instructions
1. Unplug light string from power source.
2. Pull up on the Base Lock™ unlatching the bulb from the bulb socket.
Gently pull the bulb straight out.
3. Carefully insert new bulb into socket (bulb is keyed and only goes in one
way) and push down Bulb Lock until it snaps into place.
The foot switch operates the functions of the lights. There are nine
functions, each one is activated with the press of the foot switch.
Functions occur in the following order:
Steady warm white; Steady multicolor; Fading warm white;
Fading multicolor; Warm white fading to multicolor;
Flashing warm white; Flashing multicolor;
Flashing warm white to multicolor (slow);
Flashing warm white to multicolor (fast)
Light functions always follow this sequence.
Fig. 6
Low Voltage LED Trees with PowerConnect
®
(Figure 6) PowerConnect
trees do not require the
conection of light strings
between sections.
Electrical connections are
made when each section
is assembled.
Following assembly and
shaping, connect the light
the electrical cord at base
of tree into a power
supply.
During tree assembly or
disassembly, DO NOT
DISCONNECT any of the
factory connected light
strings that are located
on the center pole or
within the tree.
Fig. 1
Fig. 2
Fig. 3
Fig. 5
SPECIAL NOTE ABOUT GIANT TREES
Some of the larger trees in our product line will include more than one middle
section. If your tree contains more than one middle section, note that each
section will be numbered in ascending order. The tree bottom section (which
inserts into tree stand) will be number 1. The next section as you build up,
will be number 2. Section 3 will follow until assembly is completed by
inserting tree top section.
Not all low voltage trees
include foot switch
DUAL COLOR
®
TREE OPERATING INSTRUCTIONS