User Manual
Table Of Contents
- Title Page
- Disclaimer
- Contact
- Table of Contents
- Welcome to MASCHINE
- Quick Reference
- Basic Concepts
- Important Names and Concepts
- Adjusting the MASCHINE User Interface
- Common Operations
- Adjusting Volume, Swing, and Tempo
- Undo/Redo
- Focusing on a Group or a Sound
- Switching Between the Master, Group, and Sound Level
- Navigating Channel Properties, Plug-ins, and Parameter Pages in the Control Area
- Navigating the Software Using the Controller
- Using Two or More Hardware Controllers
- Loading a Recent Project from the Controller
- Native Kontrol Standard
- Stand-Alone and Plug-in Mode
- Preferences
- Integrating MASCHINE into a MIDI Setup
- Syncing MASCHINE using Ableton Link
- Browser
- Browser Basics
- Searching and Loading Files from the Library
- Overview of the LIBRARY Pane
- Selecting or Loading a Product and Selecting a Bank from the Browser
- Selecting a Product Category, a Product, a Bank, and a Sub-Bank
- Selecting a File Type
- Choosing Between Factory and User Content
- Selecting Type and Mode Tags
- Performing a Text Search
- Loading a File from the Result List
- Additional Browsing Tools
- Using Favorites in the Browser
- Editing the Files’ Tags and Properties
- Loading and Importing Files from Your File System
- Locating Missing Samples
- Using Quick Browse
- Managing Sounds, Groups, and Your Project
- Playing on the Controller
- Working with Plug-ins
- Plug-in Overview
- The Sampler Plug-in
- Using Native Instruments and External Plug-ins
- Using the Audio Plug-in
- Using the Drumsynths
- Using the Bass Synth
- Working with Patterns
- Audio Routing, Remote Control, and Macro Controls
- Controlling Your Mix
- Using Effects
- Effect Reference
- Working with the Arranger
- Arranger Basics
- Using Ideas View
- Using Song View
- Section Management Overview
- Creating Sections
- Assigning a Scene to a Section
- Selecting Sections and Section Banks
- Reorganizing Sections
- Adjusting the Length of a Section
- Clearing a Pattern in Song View
- Duplicating Sections
- Removing Sections
- Renaming Scenes
- Clearing Sections
- Creating and Deleting Section Banks
- Working with Patterns in Song view
- Enabling Auto Length
- Looping
- Playing with Sections
- Triggering Sections or Scenes via MIDI
- The Arrange Grid
- Quick Grid
- Sampling and Sample Mapping
- Appendix: Tips for Playing Live
- Troubleshooting
- Glossary
- Index
The parameters described below are presented as they appear in the Control area (Arrange view).
The same parameters are available in the Plug-in panel within the Plug-in Strip (Mix view). See
↑13.4, The Plug-in Strip for more information on this.
Main Page
Element Description
MAIN Section
Engine Selects the engine used in the Hi-hat Plug-in. If you change this
setting, please refer to ↑9.4, The Hi-hats.
Tune Adjusts the pitch of the cymbal played by the middle C, measured
as a percentage. Available values range from 0.0 % to 100.0 %
(default: 50.0 %). For more details see ↑9.1.5, Pitch Range,
Tuning, and MIDI Notes.
Decay Adjusts the duration of the sound, measured as a percentage.
Available values range from 0.0 to 100.0 % (default: 65.0 %). A
short decay produces a closed hat; a long decay gives an open hi-
hat or cymbal.
Gate When enabled, the decay of the cymbal is choked by the end of the
note. When disabled (default), the cymbal plays as a one-shot
sound, i.e. until the end of its tail, no matter when the note is
released, although the sound duration will still depend on the Decay
parameter (see above).
Source Selects the sampled timbre to be used as source. Six modes are
available — A (default), B, C, D, E, and F — each corresponding to
a different cymbal.
TONE Section
Color Adjusts the frequency curve of the sound, measured as a
percentage. Available values range from 0.0 to 100.0 % (default:
71.5 %). Higher settings produce a brighter sound; lower settings
produce a more boxy sound.
Using the Drumsynths
The Hi-hats
MASCHINE MIKRO - Manual - 367