Installation Instructions

INSTALLATION INSTRUCTIONS
3 3/8” Disposer Trim
w/Basket Strainer, DR340
To use with I.S.E., Kitchen Aid, Emerson and Kenmore disposers only.
1. Separate the top mounting ring from the lower mounting ring.
2. Loosen the three bolt mounting assembly until even with top of the
mounting ring.
3. Use a regular screw driver to pry off the snap ring.
4. Apply 100% Silicone
(non-water based)
under the rim of your
Note:
Make sure Silicone does not come in contact with the
top of your New Deluxe Disposer Flange.
5. Place flange into the drain and push firmly to make sure it sits evenly in the
putty.
6. From working under the sink, slip the fiber gasket and the metal back up
ring (flat side up) that came with your waste disposer up and over the sink.
Note: You may need someone to help hold down flange sleeve until it
pops into place in the groove on the sleeve.
7. Hold the fiber gasket and metal back up ring in place with one hand and
place the mounting ring with the three bolt assembly onto the flange
sleeve. Then push the fiber gasket, metal back up ring and the mounting
ring further up on the flange sleeve and slide the snap ring onto the flange
sleeve until it pops into place in the groove on the sleeve.
8. Tighten the bolts on the three bolt mounting system until the whole
mounting system is seated evenly and tightly against the sink.
Once the above is completed follow the next installation steps from your new
Waste Disposer installation and care manual which should be found in the box.
For replacing an existing waste disposer flange with a new Deluxe Flange and
Stopper.
1. First make sure power is turned off to the waste disposer unit before
removing the disposer from the three bolt mounting assembly ring. Once this
is accomplished follow the above steps 1 though 8 for installation. Note: Make
sure to clean away all old silicone from the existing sink hole area before installing
your new Deluxe flange.
W W W . N A T I V E T R A I L S . N E T
Remove all excess silicone around the drain after the drain has been installed
new disposer flange.
INSTALLATION INSTRUCTIONS
3 3/8” Disposer Trim
w/Basket Strainer, DR340
To use with I.S.E., Kitchen Aid, Emerson and Kenmore disposers only.
1. Separate the top mounting ring from the lower mounting ring.
2. Loosen the three bolt mounting assembly until even with top of the
mounting ring.
3. Use a regular screw driver to pry off the snap ring.
4. Apply 100% Silicone
(non-water based)
under the rim of your
Note:
Make sure Silicone does not come in contact with the
top of your New Deluxe Disposer Flange.
5. Place flange into the drain and push firmly to make sure it sits evenly in the
putty.
6. From working under the sink, slip the fiber gasket and the metal back up
ring (flat side up) that came with your waste disposer up and over the sink.
Note: You may need someone to help hold down flange sleeve until it
pops into place in the groove on the sleeve.
7. Hold the fiber gasket and metal back up ring in place with one hand and
place the mounting ring with the three bolt assembly onto the flange
sleeve. Then push the fiber gasket, metal back up ring and the mounting
ring further up on the flange sleeve and slide the snap ring onto the flange
sleeve until it pops into place in the groove on the sleeve.
8. Tighten the bolts on the three bolt mounting system until the whole
mounting system is seated evenly and tightly against the sink.
Once the above is completed follow the next installation steps from your new
Waste Disposer installation and care manual which should be found in the box.
For replacing an existing waste disposer flange with a new Deluxe Flange and
Stopper.
1. First make sure power is turned off to the waste disposer unit before
removing the disposer from the three bolt mounting assembly ring. Once this
is accomplished follow the above steps 1 though 8 for installation. Note: Make
sure to clean away all old silicone from the existing sink hole area before installing
your new Deluxe flange.
W W W . N A T I V E T R A I L S . N E T
Remove all excess silicone around the drain after the drain has been installed
new disposer flange.
INSTALLATION INSTRUCTIONS
3 3/8” Disposer Trim
w/Basket Strainer, DR340
To use with I.S.E., Kitchen Aid, Emerson and Kenmore disposers only.
1. Separate the top mounting ring from the lower mounting ring.
2. Loosen the three bolt mounting assembly until even with top of the
mounting ring.
3. Use a regular screw driver to pry off the snap ring.
4. Apply 100% Silicone
(non-water based)
under the rim of your
Note:
Make sure Silicone does not come in contact with the
top of your New Deluxe Disposer Flange.
5. Place flange into the drain and push firmly to make sure it sits evenly in the
putty.
6. From working under the sink, slip the fiber gasket and the metal back up
ring (flat side up) that came with your waste disposer up and over the sink.
Note: You may need someone to help hold down flange sleeve until it
pops into place in the groove on the sleeve.
7. Hold the fiber gasket and metal back up ring in place with one hand and
place the mounting ring with the three bolt assembly onto the flange
sleeve. Then push the fiber gasket, metal back up ring and the mounting
ring further up on the flange sleeve and slide the snap ring onto the flange
sleeve until it pops into place in the groove on the sleeve.
8. Tighten the bolts on the three bolt mounting system until the whole
mounting system is seated evenly and tightly against the sink.
Once the above is completed follow the next installation steps from your new
Waste Disposer installation and care manual which should be found in the box.
For replacing an existing waste disposer flange with a new Deluxe Flange and
Stopper.
1. First make sure power is turned off to the waste disposer unit before
removing the disposer from the three bolt mounting assembly ring. Once this
is accomplished follow the above steps 1 though 8 for installation. Note: Make
sure to clean away all old silicone from the existing sink hole area before installing
your new Deluxe flange.
W W W . N A T I V E T R A I L S . N E T
Remove all excess silicone around the drain after the drain has been installed
new disposer flange.
INSTALLATION INSTRUCTIONS
3 3/8” Disposer Trim
w/Basket Strainer, DR340
To use with I.S.E., Kitchen Aid, Emerson and Kenmore disposers only.
1. Separate the top mounting ring from the lower mounting ring.
2. Loosen the three bolt mounting assembly until even with top of the
mounting ring.
3. Use a regular screw driver to pry off the snap ring.
4. Apply 100% Silicone
(non-water based)
under the rim of your
Note:
Make sure Silicone does not come in contact with the
top of your New Deluxe Disposer Flange.
5. Place flange into the drain and push firmly to make sure it sits evenly in the
putty.
6. From working under the sink, slip the fiber gasket and the metal back up
ring (flat side up) that came with your waste disposer up and over the sink.
Note: You may need someone to help hold down flange sleeve until it
pops into place in the groove on the sleeve.
7. Hold the fiber gasket and metal back up ring in place with one hand and
place the mounting ring with the three bolt assembly onto the flange
sleeve. Then push the fiber gasket, metal back up ring and the mounting
ring further up on the flange sleeve and slide the snap ring onto the flange
sleeve until it pops into place in the groove on the sleeve.
8. Tighten the bolts on the three bolt mounting system until the whole
mounting system is seated evenly and tightly against the sink.
Once the above is completed follow the next installation steps from your new
Waste Disposer installation and care manual which should be found in the box.
For replacing an existing waste disposer flange with a new Deluxe Flange and
Stopper.
1. First make sure power is turned off to the waste disposer unit before
removing the disposer from the three bolt mounting assembly ring. Once this
is accomplished follow the above steps 1 though 8 for installation. Note: Make
sure to clean away all old silicone from the existing sink hole area before installing
your new Deluxe flange.
W W W . N A T I V E T R A I L S . N E T
Remove all excess silicone around the drain after the drain has been installed
new disposer flange.