V1.1-M 13Apri2020 3 User Manual WARNING Read carefully and understand all ASSEMBLY AND OPERATION,INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety,precautions may result in serious personal injury.
T an you for c oosin a Nature Po er Pro uct This product is designed for certain applications only. The distributor cannot be responsible for issues arising from modification. We strongly recommend this product not be modified and/or used for any application other than that for which it was designed. If you have a question relative to a particular application, do not use the product until you have first contacted the distributor to determine if it can or should be performed on the product.
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. 1. SAVE THESE INSTRUCTIONS. This manual contains important safety and operating instructions for power inverter 3000W .This manual will show you how to use your inverter safely and effectively. Please read, understand and follow these instructions and precautions carefully. 2. Keep out of reach of children. 3. Do not expose inverter to rain or snow. 4. Use of an attachment not recommended or sold by the unit manufacturer may injury to persons. 5.
FEATURES • High-speed cooling fan(2) To keep the inverter cool, the fan turn on depend on temperature in the inverter. The fans do not run when the inverter is turned off. • Positive Battery Cable Terminal (Red) • Negative Battery Cable Terminal (Black) • ON/OFF rocker switch • LED indicator Green indicates Power ON Red indicates Overload/Interruption in power • 12 Volt power cord • 120V standard AC outlets (4) • USB port(s) – 5V, 2.
6. Attach the other end of the wire to a properly grounded location: Vehicle: Connect to the chassis, unpainted frame part, or engine block of the vehicle. Fixed location: Connect to a ground rod or other appropriately rated ground. CONNECTING INVERTER CABLES TO THE INVERTER 1. Locate the Positive and Negative terminals on the inverter. 2. From the POSITIVE (RED) and the NEGATIVE (BLACK) terminals, remove 3. Place the POSITIVE (RED) ring connector onto the POSITIVE (RED) inverter terminal.
Page of 14
OPERATING INSTRUCTIONS After mounting and connecting your Inverter according to the instructions in this manual, use the ON/OFF/REMOTE switch to choose the Inverter’s operating mode. ON: When you set the switch to the ON (I) position, the Inverter provides AC power to connected equipment by converting DC power from your vehicle’s battery. The green LED will illuminate to indicate it is working. OFF: Set the switch to the OFF (O) position to shut down the Inverter completely.
6. indicating the Inverter is receiving power. 4. Switch the Inverter’s ON/OFF/REMOTE switch to the OFF (O) position. The green LED may flash briefly and/or the internal speaker may beep briefly. This is normal. 5. Make sure the device(s) to be operated is turned OFF. 6. Plug the device(s) into the Inverter’s AC outlet(s). 7. Switch the inverter’s ON/OFF/REMOTE switch to the ON (I) or REMOTE (II) positions.
LED INDICATOR AND SHUTDOWN PROTECTION The Green LED lights automatically when the inverter is plugged into a 12 volt DC power source and is turned on. The Red LED lights, the alarm sounds and the inverter automatically turns itself off under the following conditions: 1. When the power input from the vehicle’s battery drops to approximately 10.5 volts, the low voltage alarm will sound. When the voltage goes down below 10 VDC, the inverter shuts off. Recharge or replace the battery. 2.
IF THE INVERTER’S FUSE BLOWS i which should not have to be replaced under normal operating conditions. A blown fuse is usually caused by reverse polarity or a short circuit within the device or equipment being operated. If a fuse does blow, take the inverter to MAINTENANCE AND STORAGE INSTRUCTIONS 1. Before each use, ensure that all of the inverter’s components are in place and in good working condition. 2. After use and before performing maintenance, unplug and disconnect the inverter. 3.
TROUBLESHOOTING PROBLEM Low or no output voltage. Red LED is lit. POSSIBLE CAUSE Poor contact at terminals OVP/OLP. SOLUTION Disconnect and reconnect the 12V connections. Using incorrect type of voltmeter to test output voltage. The battery voltage is below 10 volts. Use a true RMS reading meter. Recharge or replace the battery. Use a higher capacity inverter or The equipment being operated is decrease the load or device on the drawing too much power.
SPECIFICATIONS Nominal input voltage ..................................................................................12.8-13.2 VDC Nominal output voltage ................................................................................115±10% VAC Output frequency ...................................................................................................60±3 Hz Operating input voltage ................................................................................10.0-15.
LIMITED WARRANTY Nature Power warrants our products to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from date of purchase. In the case of product defect, contact Nature Power customer service to receive troubleshooting. If defective part or unit should be returned, a Return Authorization Number must be issued by Nature Power and the defective part or unit should be returned to the authorized location at the purchasers’ expense.
Please contact Nature Power Products to acquire more information: 1-800-588-0590 info@naturepowerproducts.com www.naturepowerproducts.