Nature's Wind Turbine User Manual
Nature's Wind Turbine Contents Welcome Important Safety Instructions Warning Caution 1 1 2 Introduction Unpack Your Nature's Wind Turbine Get to Know Your Nature's Wind Turbine 3 3 4 Using Your Nature's Wind Turbine How to Choose the Location How to Choose the Tower How to Install your Nature’s Wind Turbine How to Connect your Nature's Wind Turbine to your Nature’s Generator 7 7 8 8 12 Maintenance 14 Troubleshooting 14 Technical Specifications 15 Limited Warranty 16 1
Welcome Congratulations on the purchase of your new Nature’s Wind Turbine, a state-of-art wind turbine that recharges your Nature’s Generator through the wind. Please read these instructions thoroughly prior to installation, then store this manual in a safe place for future reference. If at any time you are unclear about this product, or require additional assistance, please do not hesitate to contact our Customer Support line at 805-383-0003 or email us at support@naturesgenerator.com .
Safety check After completing any service or repair to this device, ask the service technician to perform routine safety checks to determine that your Nature's Wind Turbine is in correct operating condition. Servicing These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
Unpack Your Nature’s Wind Turbine 1. Nature’s Wind Turbine main body 2. Hub 3. Nose cone 4. Blades x 5 5. 100-foot-long wind turbine cable Visit NaturesGenerator.
. Controller box 7. This user manual 8. Accessory bag that includes. M6 bolt x 12 (2 spare pieces) M6 nut x 12 (2 spare pieces) M6 flat washer x 12 (2 spare pieces) M6 lock washer x 12 (2 spare pieces) M16 lock nut x 1 M16 lock washer x 1 Rubber pad x 1 Hex key 8mm Hex key 6mm Hex key 5mm Ground line Visit NaturesGenerator.
Get to Know Your Nature’s Wind Turbine Blade x 5 Hub Nose Cone M16 lock washer Main Body M6 flat washer x 10 M16 nut M6 lock washer x 10 M6 Bolt x 10 M6 Nut x 10 M8 Bolt x 4 M8 Nut x 4 Rubber Pad x 1 Controller box Pipe (not included) 100-foot-long wind turbine cable Nature’s Generator (not included) Complete Electrical System Your Nature’s Wind Turbine comes with 100 foot long wind turbine cable and controller box. It is a complete electrical system to recharge your Nature’s Generator.
Grounding Every wind turbine and turbine tower need to be grounded at the tower base. Grounding the tower at its base may help prevent shocks to persons touching the tower due to lightning or electrical faults. Please take the time to review the National Electrical Code (NEC) and local building and zoning regulations for complete requirements. Your Nature’s Wind Turbine has a grounding cable included for this purpose.
Using Your Nature’s Wind Turbine How to choose the location The wind speed has dramatic effects on your Nature’s Wind Turbine. The location shall be carefully considered to achieve the optimal performance of your Nature’s Wind Turbine, prior to the mounting of your Nature’s Wind Turbine. Each installation is unique and often a compromise among surrounding environment, distance between your Nature’s Wind Turbine and your Nature’s Generator, zoning requirements, budget and etc.
How to choose the tower Your Nature’s Generator is designed to mount on nominal 1.5 inch schedule 40 steel tubing or piping. The outside diameter of the tubing or piping shall be around 1.875 inch to 1.900 inch. The steel tubing or piping should be available through your local hardware store. Under no circumstances should plastic pipe be used to construct a tower. Towers must be capable of withstanding 160 pounds of load in the horizontal direction at the wind turbine.
Step 3: The rubber gasket that is stored inside of the yaw and the included rubber pad help to prevent the the yaw from contacting the pipe directly. The rubber gasket and rubber pad will assist in reducing the transmission of noise and vibration down the pipe. Slide the yaw shaft all the way down over the top of the pipe and be careful not to pinch the cable. There may be some slight variances of the thickness or size of the pipe from different makers or models.
Step 5: Place one of the blades on one of the hub socket. Place a lock washer and then a flat washer on the blot and then insert the bolt through the blade ad the socket. Place a nut on the other side of socket and tighten the bolt with the 5mm hex key. Repeat this process on all five blades. Make sure the lock washer and flat washer are placed in the right order. The blades will become loose if it is not installed properly.
Step 7: Insert the 8mm hex key into the rotor shaft. Hold the blade assembly and tighten the M16 nut by turning the 8mm hex key counter clockwise. If needed, please use the extender (not included) to extend 8mm hex key to tighten the lock nut. Finally, spin the blades slowly to be sure they turn freely and the hub does move in along the rotor shaft. Step 8: Place the nose cone over the center line of the blade assembly and snap the nose cone into place.
How to connect your Nature’s Wind Turbine to your Nature’s Generator Step 1: Connect the wind turbine cable to the round connector from one side of the controller box by pushing and twisting the connectors Step 2: Connector the square connector from the other side of controller box to your Nature’s Generator “WIND INPUT” port. Visit NaturesGenerator.
Step 3: When your Nature's Wind Turbine spins at certain speed, you will see the whole display on your Nature's Generator lights up, if your Nature's Generator main power is switched off. It means your Nature's Wind Turbine is recognized by your Nature's Generator, but it is not powerful yet to recharge your Nature's Generator. When your Nature's Wind Turbine spins at proper speed, you will see the wind turbine icon on the display illuminates and battery bar starts running.
MAINTENANCE Your Nature’s Wind Turbine has been designed to run for long periods without requiring any maintenance. Performance will be enhanced if you periodically inspect your system. Review the following simple maintenance procedures and implement every six months. Caution: Do not go near the wind turbine during operation. • Check blades for superficial damage. Replace blades if damaged.
Technical Specifications Material: Wind turbine blades: fiberglass nylon composite Wind turbine body: cast aluminum alloy with powder coating Wind turbine cable: 12AWG pure copper cable Connectors: Wind turbine cable connectors: weatherproof M19 3P connectors. Wind input connectors: Anderson connectors. Yaw: fits 1.
Limited Warranty One Year Limited Warranty HuntKey USA Inc. warrants to you, the original purchaser of this new product, that the product shall be free of defects in the original manufacture of the material or workmanship for a period of one (1) year from the original date of your purchase of the product (“Warranty Period”). This product must be purchased from an authorized dealer and packaged with this warranty statement. This warranty does not cover refurbished product.
What does the Warranty not Cover? This warranty does not cover: • Cosmetic damage • Damage due to acts of God, such as lightning strikes • Accident • Misuse • Abuse • Negligence • Commercial use • Modification of any part of the product • Damage due to incorrect operation or maintenance • Connection to an incorrect voltage supply • Attempted repair by anyone other than a facility authorized by Huntkey USA Inc.
V1.