NTV-DOC272 JH (rev 1.
Overview The BENTLEY-HUR allows you to install any (double din) after market head unit into Bentley GT / GTC / SPUR 2004-2011. Everything you need to install the after market head unit is contained within this kit. Kit Content *NOTE: For U.S.
Installation IMPORTANT NOTE: The original Navigation, CD changer and the Telephone kit must be disconnected (details shown in the following pages). REAR OF MAIN UNIT OEM HARNESS (32 WAY) NOT USED (FUTURE UPGRADES) OEM HARNESS (MINI ISO) OEM HARNESS (POWER) NOT USED (FUTURE UPGRADES) USB (PROGRAM ONLY) MAIN POWER HARNESS (3)* DIP SWITCH 12v+ FOR ACC SW CONTROLS OUTPUT (2) 3,1 &2/25 :+,7( PP -$&. 67((5,1* :+((/ 6LJQDO 1 RED %/$&. PP -$&.
Installation CONNECTIONS IMPORTANT NOTE: After all the connections are made and the BENTLEY-HUR is powered up, remove the key ensuring all doors, boot and bonnet are closed. Also ensure the lights are off. Lock the car wait until the cluster goes to sleep, and allow an extra minute for the CAN to go to sleep. Now unlock as normal and the BENTLEY-HUR panel is now ready to use. Make all connections from the BENTLEY-HUR to your aftermarket head-unit using the supplied harnesses.
Installation Take trim remover and pry the speaker grill up and remove Take hold of the trim panel and pull from the top and the bottom to remove Lift trim panel and disconnect the black connector Remove the 5 screws (t20 torx) as shown in photo Page 5
Installation Carefully remove the Bentley head unit Disconnect all connections to factory radio and remove from car. Disconnect the Navigation CD drive in the glovebox.
Installation Disconnect the CD Changer in the glovebox. Remove the fuse for the phone module.
Installation Remove the navigation drive and the CD changer to make it easier to run the supplied GPS extension lead.
Installation Remove the 4 x trim clip from original ZAB unit and clip into the supplied fasica For the after market microphone and possible DAB antenna (GT / SPUR: N/A for US vehicles) remove the A pillar trim Pry back trim next to door seal and use a feeder cable to get through to the glove box Page 9
Installation To remove the roof console you will require a right angled pick. Gently pry the OEM mic and alarm sensor out of the consol and remove the 2 x t20 torx screws behind, then pull down console. Non-US vehicles only: On GT / SPUR there are only certain locations where you can put the DAB antenna as the glass in the car is polarised and will affect reception. Top of the front screen is not polarised. Once you have completed all the above, refit the trim panel and test to ensure all functions.
Operation For full details on the operation of the BENTLEY-HUR fascia panel, please consult the USER GUIDE Troubleshooting 4 $ 6WHHULQJ ZKHHO FRQWUROV GRQ W ZRUN 3OHDVH FKHFN WKH GLS VZLWFKHV DUH VHW FRUUHFWO\ IRU \RXU FKRVHQ KHDG XQLW 4 7KH %(1TLEY +85 SDQHO LV QRW IXQFWLRQLQJ FRUUHFWO\ DIWHU LQLWLDO LQVWDOO $ 3OHDVH VHH ³LPSRUWDQW QRWH´ RQ SDJH 4 $ 1R *36 UHFHSWLRQ RQ DIWHU PDUNHW XQLW &KHFN FRQQHFWLRQ RI WKH *36 H[WHQVLRQ OHDG VXSSOLHG LQ WKH NLW 4 $ 7KH /&' VFUHHQ NH
