Operation Manual
Table Of Contents
- Section 1 - General information
- Section 2 - Basic operation and key functions
- Section 3 - Radio MENU SELECT options
- 3-1 Manage your waypoints list (WAYPOINT)
- Section 4 - Radio setup menu (RADIO SETUP)
- 4-1 Channel (UIC)
- 4-2 Channel names (CH NAME)
- 4-3 Ring volume (RING VOLUME)
- 4-4 Key beep volume (KEY BEEP)
- 4-5 Select units (UNITS)
- 4-6 Internal speaker connections (INT SPEAKER)
- 4-7 Set the priority channel (WATCH MODE)
- 4-8 Weather alerts (WX ALERT)
- 4-9 NMEA protocol (COM PORT)
- 4-10 Select the GPS source (GPS SOURCE)
- 4-11 Favourite channel setup - Wx key (FAV CH SETU)
- 4-1 Channel (UIC)
- Section 5 - DSC setup menu (DSC SETUP)
- 5-1 Enter or view your USER MMSI (USER MMSI)
- 5-2 Maintain your groups
- 5-3 Enter or check your ATIS MMSI (ATIS MMSI)
- 5-4 Enable ATIS functionality (ATIS SELECT)
- 5-5 Response to individual calls (INDIV REPLY)
- 5-6 Enable DSC functionality (DSC FUNC)
- 5-7 Response type to LL polling calls (LL REPLY)
- 5-8 Automatic channel switching (AUTO SWITCH)
- 5-9 DSC Test Reply (TEST REPLY)
- 5-10 Set the inactivity timer (TIMEOUT)
- 5-1 Enter or view your USER MMSI (USER MMSI)
- Section 6 - AIS setup menu (AIS SETUP)
- Section 7 - Wireless handset setup menu (HS SETTING)
- Section 8 - Sending and receiving DSC Calls
- 8-1 What is DSC?
- 8-2 Sending DSC Calls
- 8-3 Send an individual call (INDIVIDUAL)
- 8-4 Acknowledgement of an individual incoming call (INDIV)
- 8-5 Reply to the Last Call (LAST CALL)
- 8-6 Send a group call (GROUP)
- 8-7 Send an all ships call (ALL SHIPS)
- 8-8 Send using the call log (CALL LOG)
- 8-9 Send using the distress log (DIST LOG)
- 8-10 View sent call log (SENT CALL)
- 8-11 Request the LL position of a Buddy (LL REQUEST)
- 8-12 Track your Buddy (TRACK BUDDY)
- 8-13 Make a DSC test call (DSC TEST)
- 8-14 View user MMSI and GPS information
- 8-15 Receiving DSC calls
- 8-16 Receiving an all ships call (ALL SHIPS)
- 8-17 Receiving an individual call (INDIV)
- 8-18 Receiving a group call (GROUP)
- 8-19 Receiving a geographic area call (GEOGRAPH)
- 8-20 Receiving a polled position call (POSITION)
- 8-1 What is DSC?
- Section 9 - DISTRESS calls
- Section 10 - AIS functionality
- Section 11 - General functionality
- Section 12 - Wireless Handset functionality
Section 6 - AIS setup menu (AIS SETUP)
Hold down CALL/MENU key for about 1 second to access the following AIS SETUP options.
The following menu options are explained in this section.
AIS SETUP AIS FUNC Section 6-1
AIS DISPLAY Section 6-2
BAUD RATE Section 6-3
GPS REDIR Section 6-4
CPA ALARM Section 6-5
CPA Section 6-6
TCPA Section 6-7
5-9 DSC Test Reply (TEST REPLY)
You can respond to incoming DSC TEST calls with an automatic response or with a manual
response.
• MANUAL manual response is required, press ENT to confirm or press EXIT to cancel.
• AUTO automatically replies after a 10 second delay with an ACK to any incoming
DSC TEST call.
DSC SETUP
LL REPLY ▲
AUTO SWITC
►TEST REPLY
TIMEOUT
TEST REPLY
►AUTO
MANUAL
5-10 Set the inactivity timer (TIMEOUT)
You can set the inactivity timer with the following options:
• AUTOMATED you can set the inactivity timer to automatically timeout after a
period of inactivity for the following two categories: NON-DISTRESS or
DISTRESS.
Timeout options are:
DISTRESS: NO TIMEOUT; 5 MINS; 10 MINS (default is NO TIMEOUT)
NON-DISTR: NO TIMEOUT; 10 MINS; 15 MINS (default is 15 MINS)
• NON AUTO you can set the inactivity timer to exit any non-automated procedure
activity.
Timeout options are:
NO TIMEOUT; 10 MINS; 15 MINS (default is 10 MINS)
Note: If NO TIMEOUT is selected, then you must press the EXIT key to exit the procedure.
Example: to set a 10 minute TIMEOUT for non-automated functions:
1. Select TIMEOUT, then select NON AUTO
2. Select desired timeout period: NO TIMEOUT, 10 MINS or 15 MINS
NON AUTO
NO TIMEOUT
►10 MINS
15 MINS
TIMEOUT
►AUTOMATED
NON AUTO
DSC SETUP
LL REPLY ▲
AUTO SWITC
TEST REPLY
►TIMEOUT
In this example, 10 MINS has been selected, meaning the radio will exit any non-automated
procedure after a period of 10 minutes of non-activity.
Simrad - RS35 Operation InstructionsSimrad - RS35 Operation Instructions 4342
See sections 1-3 and 1-4 if you want to know how to move around the menu and enter, save
and change data.
6-1 Enable AIS functionality (AIS FUNC)
The AIS function can be turned ON or OFF. When AIS functionality is selected, the AIS symbol
AIS
is shown on the LCD.
AIS SETUP
►AIS FUNC
AIS DISPLAY
BAUD RATE
GPS REDIR
AIS FUNC
►ON
OFF
6-2 AIS data display format (AIS DISPLAY)
When viewing the AIS plotter screen, AIS targets can be displayed with the vessels name or
the vessels MMSI.
AIS SETUP
►AIS DISPLAY
BAUD RATE
GPS REDIR
CPA ALARM
AIS DISPLAY
►SHIP MMSI
SHIP NAME
6-3 AIS baud rate (BAUD RATE)
AIS data can be output to a compatible chart-plotter / MFD or PC via the NMEA port. The
NMEA port baud rate can be set to 4800 or 38400. The default setting is 38400. If 4800 is
selected, a warning that data may be lost is displayed.
AIS SETUP
►BAUD RATE
GPS REDIR
CPA ALARM
CPA
AIS SETUP
38400
►4800
AIS INFO
MAY BE LOST!
►NO
YES