Operation Manual
Table Of Contents
- Section 1 - General information
- Section 2 - Basic operation and key functions
- Section 3 - Radio MENU SELECT options
- 3-1 Manage your waypoints list (WAYPOINT)
- Section 4 - Radio setup menu (RADIO SETUP)
- 4-1 Channel (UIC)
- 4-2 Channel names (CH NAME)
- 4-3 Ring volume (RING VOLUME)
- 4-4 Key beep volume (KEY BEEP)
- 4-5 Select units (UNITS)
- 4-6 Internal speaker connections (INT SPEAKER)
- 4-7 Set the priority channel (WATCH MODE)
- 4-8 Weather alerts (WX ALERT)
- 4-9 NMEA protocol (COM PORT)
- 4-10 Select the GPS source (GPS SOURCE)
- 4-11 Favourite channel setup - Wx key (FAV CH SETU)
- 4-1 Channel (UIC)
- Section 5 - DSC setup menu (DSC SETUP)
- 5-1 Enter or view your USER MMSI (USER MMSI)
- 5-2 Maintain your groups
- 5-3 Enter or check your ATIS MMSI (ATIS MMSI)
- 5-4 Enable ATIS functionality (ATIS SELECT)
- 5-5 Response to individual calls (INDIV REPLY)
- 5-6 Enable DSC functionality (DSC FUNC)
- 5-7 Response type to LL polling calls (LL REPLY)
- 5-8 Automatic channel switching (AUTO SWITCH)
- 5-9 DSC Test Reply (TEST REPLY)
- 5-10 Set the inactivity timer (TIMEOUT)
- 5-1 Enter or view your USER MMSI (USER MMSI)
- Section 6 - AIS setup menu (AIS SETUP)
- Section 7 - Wireless handset setup menu (HS SETTING)
- Section 8 - Sending and receiving DSC Calls
- 8-1 What is DSC?
- 8-2 Sending DSC Calls
- 8-3 Send an individual call (INDIVIDUAL)
- 8-4 Acknowledgement of an individual incoming call (INDIV)
- 8-5 Reply to the Last Call (LAST CALL)
- 8-6 Send a group call (GROUP)
- 8-7 Send an all ships call (ALL SHIPS)
- 8-8 Send using the call log (CALL LOG)
- 8-9 Send using the distress log (DIST LOG)
- 8-10 View sent call log (SENT CALL)
- 8-11 Request the LL position of a Buddy (LL REQUEST)
- 8-12 Track your Buddy (TRACK BUDDY)
- 8-13 Make a DSC test call (DSC TEST)
- 8-14 View user MMSI and GPS information
- 8-15 Receiving DSC calls
- 8-16 Receiving an all ships call (ALL SHIPS)
- 8-17 Receiving an individual call (INDIV)
- 8-18 Receiving a group call (GROUP)
- 8-19 Receiving a geographic area call (GEOGRAPH)
- 8-20 Receiving a polled position call (POSITION)
- 8-1 What is DSC?
- Section 9 - DISTRESS calls
- Section 10 - AIS functionality
- Section 11 - General functionality
- Section 12 - Wireless Handset functionality
Section 11 - General functionality
11-1 Using the Fog Horn
An appropriate PA speaker must be connected to the Hailer wiring before the FOG HORN
function can be used. The FOG HORN will sound certain international standard fog horn
tones through the hailer speaker depending on the mode selected.
1. Press and hold the AIS/IC button for about 1 second to enter HAILER mode. Select FOG
HORN and press ENT.
2. There are 8 choices of internationally recognized fog horn sounds and timing:
• HORN (Horn) Manual operation
• UNDERWAY (Underway) One long tone
• STOP (Stop) Two long tone
• SAIL (Sail) One long, two short
• ANCHOR (Anchor) One long warble
• TOW ( Tow) One long, three short
• AGROUND (Aground) Warble sequence
• SIREN (Siren) Manual operation
3. Scroll through the menu to select a fog horn type, then press ENT to start the selected
fog horn sounding. All except HORN and SIREN will sound automatically.
4. The fog horn will sound automatically approximately every two minutes until you press
EXIT to cancel it. When the fog horn is not sounding, it is in LISTEN mode.
5. To change the volume, turn the Channel Select knob, or press + or – when the fog horn
is sounding.
6. To operate HORN or SIREN, once selected, press and hold ENT button. This will sound
as long as the ENT button is pressed. You can then also operate PTT to talk through the
Hailer.
HAILER
PA
►FOG HORN
INTERCOM
FOG HORN
►HORN
UNDERWAY
STOP
SAIL
▼
FOG HORN
UNDERWAY
▲
STOP
►SAIL
ANCHOR
▼
SAIL
OUTPUT
VOL
LO HI
Note: you cannot change the volume of the HORN or SIREN.
11-2 Using the PA (Public Address) Hailer
An appropriate Hailer speaker must be connected to the Hailer wiring before the PA function
can be used. The PA allows you to make an announcement at high volume to people or
vessels using the RS35 hand mic. The PA function also features a listen-back mode where the
speaker is used as a microphone to listen for a response.
1. Press and hold the AIS/IC button for about 1 second to enter HAILER mode. Select PA
and press ENT.
2. Press PTT to talk through the hailer. Turn the Channel Select knob, or press + or – to
change the volume. Volume can only be changed while the PTT is pressed.
3. Release PTT to LISTEN for a response.
HAILER
►PA
FOG HORN
INTERCOM
PA
OUTPUT
VOL
LO HI
PA
LISTEN
4. Press EXIT to return to operational mode.
Simrad - RS35 Operation InstructionsSimrad - RS35 Operation Instructions 6766