Operation Manual
Table Of Contents
- Section 1 - General information
- Section 2 - Basic operation and key functions
- Section 3 - Radio MENU SELECT options
- 3-1 Manage your waypoints list (WAYPOINT)
- Section 4 - Radio setup menu (RADIO SETUP)
- 4-1 Channel (UIC)
- 4-2 Channel names (CH NAME)
- 4-3 Ring volume (RING VOLUME)
- 4-4 Key beep volume (KEY BEEP)
- 4-5 Select units (UNITS)
- 4-6 Internal speaker connections (INT SPEAKER)
- 4-7 Set the priority channel (WATCH MODE)
- 4-8 Weather alerts (WX ALERT)
- 4-9 NMEA protocol (COM PORT)
- 4-10 Select the GPS source (GPS SOURCE)
- 4-11 Favourite channel setup - Wx key (FAV CH SETU)
- 4-1 Channel (UIC)
- Section 5 - DSC setup menu (DSC SETUP)
- 5-1 Enter or view your USER MMSI (USER MMSI)
- 5-2 Maintain your groups
- 5-3 Enter or check your ATIS MMSI (ATIS MMSI)
- 5-4 Enable ATIS functionality (ATIS SELECT)
- 5-5 Response to individual calls (INDIV REPLY)
- 5-6 Enable DSC functionality (DSC FUNC)
- 5-7 Response type to LL polling calls (LL REPLY)
- 5-8 Automatic channel switching (AUTO SWITCH)
- 5-9 DSC Test Reply (TEST REPLY)
- 5-10 Set the inactivity timer (TIMEOUT)
- 5-1 Enter or view your USER MMSI (USER MMSI)
- Section 6 - AIS setup menu (AIS SETUP)
- Section 7 - Wireless handset setup menu (HS SETTING)
- Section 8 - Sending and receiving DSC Calls
- 8-1 What is DSC?
- 8-2 Sending DSC Calls
- 8-3 Send an individual call (INDIVIDUAL)
- 8-4 Acknowledgement of an individual incoming call (INDIV)
- 8-5 Reply to the Last Call (LAST CALL)
- 8-6 Send a group call (GROUP)
- 8-7 Send an all ships call (ALL SHIPS)
- 8-8 Send using the call log (CALL LOG)
- 8-9 Send using the distress log (DIST LOG)
- 8-10 View sent call log (SENT CALL)
- 8-11 Request the LL position of a Buddy (LL REQUEST)
- 8-12 Track your Buddy (TRACK BUDDY)
- 8-13 Make a DSC test call (DSC TEST)
- 8-14 View user MMSI and GPS information
- 8-15 Receiving DSC calls
- 8-16 Receiving an all ships call (ALL SHIPS)
- 8-17 Receiving an individual call (INDIV)
- 8-18 Receiving a group call (GROUP)
- 8-19 Receiving a geographic area call (GEOGRAPH)
- 8-20 Receiving a polled position call (POSITION)
- 8-1 What is DSC?
- Section 9 - DISTRESS calls
- Section 10 - AIS functionality
- Section 11 - General functionality
- Section 12 - Wireless Handset functionality
Section 12 - Wireless Handset functionality
This radio can operate with up to two optional HS35 wireless handsets. When an HS35
wireless handset is successfully 'subscribed' to the radio, the button and screens on each
device will be mimicked.
Note: The HS35 must be subscribed to the RS35 base-station radio before it can be used. See
Section 7 on how to subscribe the wireless handset to the RS35.
Note: Maximum of two handsets can be subscribed to the RS35.
12-1 Using the Wireless Handset
Once the HS35 handset has been paired (subscribed) to the RS35, the screen and button
functionality are mimicked on each device.
Most functions that are provided for on the RS35 can be accessed by the HS35 with the
following differences:
• AIS: There is no AIS PPI on the HS35 screen
• SETUP: Some setup functions are not available on the HS35
When the HS35 is not in use, it should be placed back into the charger cradle. The HS35 is
charged when placed in the cradle via a contact-less inductive charging system.
12-2 Using the Intercom / Conference facility
The Intercom mode works ONLY when one or two optional HS35 handset(s) are installed.
Conference mode is only available when 2 handsets are connected and is used to connect all
3 units together. This disables the radio receiver except for incoming DSC calls.
1. Hold down AIS/IC key to enter INTERCOM or CONFERENCE mode.
HAILER
PA
FOG HORN
►INTERCOM
INTERCOM
PUSH TO TALK
2. The intercom calls the other unit.
3. Press PTT when invited.
4. Press ESC to exit the INTERCOM mode
Simrad - RS35 Operation InstructionsSimrad - RS35 Operation Instructions 6968