NL-6003P u-blox NEO-6P MD6/seriell Receiver Operation manual (62457)
1. Introduction The NL-6003P is a MD6/serial GNSS receiver with internal antenna and ublox NEO-6P GPS module. This module allows a positioning accuracy of under one metre through a combination of PPP (Precision point Positioning) and SBAS technologies. The MD6/serial interface enables connection to a notebook, UMPC, tablet or car PC. The receiver's bottom side is rubberized and magnetic, which allows for universal positioning.
2. Starting operation You may connect the NL-6003P either to the serial interface of your PC using an MD6 to DB9 adapter cable, or to the USB interface of your PC using an MD6 to USB adapter cable. MD6 to DB9: http://www.navilock.de/produkte/G_61265/merkmale.html?setLanguage=en MD6 to USB: http://www.navilock.de/produkte/G_61264/merkmale.html?setLanguage=en All values for the serial connection via DB9, such as COM Port, Baud rate etc., result from the settings of this interface on your PC.
If the NMEA protocol is displayed in u-Center, but you cannot find a receiver in the application software, the connection problem is not with the receiver, but with the selected software setting. In this case, the software manufacturer support center may be able to help you. 7 6 5 1 2 4 3 After starting the u-Center software, check the functionality of your NL-6003P. 1. Selecting the COM port 2. Selecting the baud rate 3. Downloading Assist GPS and updating the receiver 4.
6. EGNOS configuration with u-Center 7.xx NL-6003PU use EGNOS as default. In the configuration menu you can check these options. For detailed information please use the documentation from u-blox http://www.u-blox.com. 7. Assist GPS configuration with u-Center 7.xx The NL-6003P supports AssistNow! AssistNow is a standard A-GPS service, which increases the performance of the GNSS receiver, by calculating a position almost immediately, even under difficult reception conditions.
Further information to the u-Center can be found in the u-blox documentation under http://www.u-blox.com/products/u_center.html If you have any questions, please contact u-blox directly. Danger of explosion at contact with fire! Do not permanently expose the receiver to temperatures of over 60°C (140°F). 8. Possible sources of error and their elimination 8.1 The green LED doesn’t light up after the first connection to the USB port.
9. Specifications Chipset manufacturer/type u-blox NEO-6P GPS Channels: Sensitivity: Frequency: C/A Code: 50 channels -160 dBm L1, 1575.42 MHz 1.023 MHz Target precisions: GPS Position horizontal: SBAS + PPP < 1 m (2D, R50) SBAS + PPP < 2 m (3D, R50) Demonstrated under following conditions: 24 hours, stationary, first 600 seconds of data discarded. HDOP < 1.5 during measurement period, strong signals. Continuous availability of valid SBAS correction data during full test period.
11. Warranty period Your GPS receiver will be repaired free of charge within the legal warranty period, unless it was damaged due to external cases, humidity dropping or other damages due to improper usage. Your dealer is always ready to help you. Please send your unit for repairs directly to: Navilock Repair Center Beeskowdamm 13/15 D-14167 Berlin-Zehlendorf Postage must always be paid by the client. Please add a proof of purchase and a detailed error description.
Conformity declaration Please download the Declaration of Conformity from http://www.navilock.de/support/ in the conformity area. WEEE note The WEEE (Waste Electrical and Electronic Equipment) directive, which came into force on 13 February 2003, lead to a comprehensive change in the disposal of used electric products.
