WIND 3150 Installation and Operation Manual w w w. n a v m a n . c o m English ............. 2 Français ......... 16 Español .......... 29 Português ......
FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Contents 1 Introduction ..................................................................................................... 4 2 Operation ......................................................................................................... 5 2-1 Turn on and off ............................................................................................................ 5 2-2 The keys ......................................................................................................................
1 Introduction The WIND 3150 displays: Apparent wind angle and wind speed. True wind angle and wind speed (requires data from a boat speed instrument). Maximum wind speed. VMG, the component of boat speed parallel to the wind (requires data from a boat speed instrument). An installed WIND 3150 has two parts: The display unit. The masthead unit, which has devices for measuring wind speed and wind angle. The unit is powered from the boat’s power supply.
2 Operation 2-1 Turn on and off Turn the unit on and off with the auxiliary power switch on the boat. The unit does not have its own power switch. When the unit is turned on, the pointer rotates once as the unit performs a self-calibration. When the unit is turned off, any settings you have made are retained. If the word SIM flashes on the LCD display then the unit is in simulate mode (see section 2-5). 2-2 The keys The unit has four keys, labelled In this manual: and .
2-7 Key reference Turn alarm on or off Turn power on Hold Hold + 5 sec Set alarm Turn Simulate on or off Set Wind Speed alarm Reset memory Hold 2 sec Normal operation Return to normal operation (If the alarm is sounding) Mute the alarm Set Wind Damping Change wind mode (TRUE or APP [Apparent]) Calibrate Wind Angle + + Change LCD display (Wind speed, wind angle, VMG, Max wind speed) Adjust backlight (4 levels or off) Calibrate Wind Speed + Select Backlight Group + Set Speed Mode Hold 2 sec
3 Display apparent or true wind speed and angle Apparent wind speed and angle are the values measured by the masthead unit on the boat. True wind speed and angle are calculated values that allow for the relative speed of the boat. wind speed and angle.
4 Display wind angle The pointer shows wind angle in degrees (0 to 180° port or starboard). To display the numeric wind angle as well, press until the degrees symbol is displayed, for example: Wind angle Wind from 30° to starboard Degrees symbol If the WIND 3150 is connected to a boat speed instrument, press to display TRUE or APP (apparent) wind angle (see section 3). 4-1 Set wind damping Wind turbulence, gusts and mast motion cause the measured wind angle and speed to fluctuate.
6 Display maximum wind speed To display maximum wind speed, press until the maximum speed is displayed, for example: The maximum wind speed is the highest measured apparent wind speed since the maximum wind speed was reset or the unit was switched on. 6-1 Reset maximum wind speed Resetting starts calculating a new maximum: 1 Press 2 Hold until MAX speed is displayed. + for two seconds.
travel at maximum speed when there is no wind; the correct wind speed is then equal to the boat speed. Find the boat speed from a speed instrument in the boat or in another boat travelling at the same speed. 2 3 After two seconds, the display changes to display the apparent wind speed: 4 Press or to change the displayed apparent wind speed to the correct value. 5 Press .
10 WIND 3150 hardware 10-1 What comes with your WIND 3150 Standard configuration: WIND 3150 unit with protective cover. Masthead unit. 30 m (98 ft) Masthead cable. Masthead cable junction box. Warranty card. Mounting template. This Installation and Operation Manual. 10-2 Other parts required One or more 3100 series instruments will be connected to the boat 12 V DC power supply via: An accessory switch to turn the instruments on and off. A fuse. Use a 1 A fuse for between one and five instruments.
11 Installation and setup Correct installation is critical to the performance of the unit. It is vital to read this section of the manual and the documentation that comes with the other parts before starting installation. The WIND 3150 can: Side view of display unit mounting: Fixing hole 50 mm (2") 20 mm (0.75") maximum panel thickness Fixing nut Drive external beepers or lights for the alarm. Send and receive data from other NAVMAN instruments connected via NavBus.
box needs to be. Allow extra length for terminating the cable in the junction box. Cut the masthead cable to this length from the mounting block. Do not throw away the other piece of cable. 5 Lead the bare end of the masthead cable into the hole at the top of the mast, down the conduit in the mast and out the hole at the bottom of the mast. Fit a strain relief clamp or cable tie to the cable at the mast top. Fill both cable holes in the mast with sealant.
With several instruments, use the optional junction boxes to simplify wiring, as shown below: instrument that outputs speed through water and to an instrument that outputs speed over ground, then you can select which the WIND 3150 will use (see section 9): i Group 1 Junction box Press + several times until the Speed Mode screen is displayed: Power & data connections Power/data cables Group 2 NavBus cable Junction box Power & data connections ii After two seconds, the modeBacklight is displayed, flas
Appendix A - Specifications Physical Case size 111 mm (4.4") square. LCD display 27 mm (1.1") wide, 18 mm (0.7") high; twisted nematic. LCD digits 14 mm (0.55") high. Four operator keys, laser etched. Backlighting for display and keys, amber, four levels and off (the key backlight does not turn off). Operating temperature 0 to 50°C (32 to 122°F). Power cable length 1 m (3.25 ft). Masthead unit cable length 30 m (99 ft). Electrical Power supply 10.5 to 16.
Appendix C - How to contact us www.navman.com NORTH AMERICA ASIA MIDDLE EAST NAVMAN USA INC. 18 Pine St. Ext. Nashua, NH 03060. Ph: +1 603 577 9600 e-mail: sales@navmanusa.com China Peaceful Marine Electronics Co. Ltd. Hong Kong, Guangzhou, Shanghai, Qindao, Dalian. E210, Huang Hua Gang Ke Mao Street, 81 Xian Lie Zhong Road, 510070 Guangzhou, China. Ph: +86 20 3869 8784 e-mail: sales@peaceful-marine.com Website: www.peaceful-marine.
Lon 174° 44.535’E WIND 3150 Made in New Zealand MN000199B NAVMAN Lat 36° 48.
