To ensure safety while driving and to comply with laws, drivers should not watch video or operate the video device while driving.
Content Precaution...................................... 2 Basic Operation............................... 23 Safety Information......................... 3 Selecting Play Mode......................... 23 Disc Notes .................................... 4 On-Screen Display Function..............25 Installation .................................... 5 Digital Video Special Function........ 26 Electric Connection ...................... 9 Multi-Subtitle Language function....... 26 Remote Control .........
Precaution THANK YOU FOR PURCHASING THIS CAR DIGITAL VIDEO PLAYER . Before operating the unit, read this manual thoroughly and keep it handy for future reference . To avoid injury or accident , read the following precautions before installing and operating the unit . ON INSTALLATION DO NOT install any receiver in locations where; - it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.
Safety Information CAUTION: THIS DIGITAL VIDEO PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DIGITAL VIDEO PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE . HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DIGITAL VIDEO PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
DISC NOTES Disc formats supported by this player Digital Video Digital Video (although not enough to make it unusable) depending on your handling it and conditions in the usage environment. Note these scratches are not an indication of any problem with the player.
Installation NOTES: Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
Installation Installating the unit DASH BOARD METAL MOUNTING STRAP HEX NUT SPRING WASHER PLAIN WASHER CONSOLE TAPPING SCREW SLIDE BRACKET HOUSING HEX BOLT SCREWDRIVER TABS KEY PLATE PLASTIC TRIM OUT KEY PLATE If you want to take CHASSIS out of the SLIDE BRACKET HOUSING, first remove the PLASTIC TRIM OUT of the both sides away, then insert the two KEY PLATE into left and right side of chassis as above illustration.
Installation How To Remove And Install The Front Panel When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. Detaching The Front Panel Before detaching the control panel, be sure to turn off the power. 1).
Installation ATTACHING THE FRONT PANEL 1). First, insert the left side of the front panel into the main unit(SEE 1 ). (Note: the “Hollow ” point on the front panel must be attached into the “Bulge” point of the unit . ) 2). Gently push the right-down hand side of the front panel until you feel a “ Click” . (SEE 2 ) Bulge Hollow 1 2 Precautions Do not touch the contacts on the front panel or the unit body, since this may result in poor electrical contact.
Electric Connection WIRING CONNECTION REAR RCA OUTPUT CABLE RCH RED REAR CAMERA INPUT YELLOW SUBWOOFER GREY VIDEO IN YELLOW RCA CABLE LCH WHITE FRONT RCA OUTPUT CABLE FRONT RCA RED R VIDEO OUT YELLOW FRONT RCA WHITE L RADIO ANTENNA JACK ISO CONNECTOR PINK IGNITION SWITCH(B+) MEMORY BACK-UP(B+) RED BROWN YELLOW GROUND(B-) BLUE BLACK FRONT LCH SPK. REAR LCH SPK.
Remote Control 15 MODE 17 7 2 MUTE PLAY/PAUSE 16 STOP 3 REDIAL ANGLE MO/ST ZOOM 19 13 22 20 PAIR 1 LOUD MENU EQ CLK LO/DX 21 6 14 23 OSD 24 18 BAND 9 ENTER TITLE/PBC A/PS TOP RPT INT 1 2 3 4 5 6 SEL 7 8 9 SETUP GOTO +10 0 VOL 11 10 4 VOL 12 RDM 8 Ref # Button 5 27 26 25 Function 1 CLK Press it briefly to view the clock time .
Remote Control Ref # Button 8 GOTO 9 / Function Press this button to begin playback at a moment in the program you designate. Use number buttons to enter the data that is needed. In BT menu, it serves as the asterisk button on your mobile handset. Press these buttons to skip ahead or back one track.
Remote Control Function Ref # Button 23 This button is used to confirm selections and settings within many ENTER of the menus in the OSD system. In DISC mode, press it to reverse rapidly 24 Use to input numerical values during programming, with the GOTO button, or to directly select a track to play . 25 0-9 26 +10/ This button is used with the other number buttons for use with two-digit number entries. In BT menu, it serves as the hash button on your mobile handset.
Basic Operation POWER ON/OFF Touch the “ ” ICON on screen to turn the unit off . Press the“ ” onthe front panel to turn It on, press it again to turn off . FIG.2 LOADING/EJECTING A DISC Loading a Disc 1. Press the POWER ( ) button on the front pane to turn the device on . Adjusting the viewing angle . When the monitor does not move, you press button on the panel to turn the monitor upward or downward at fine steps to get a desired viewing angle . 2.
Basic Operation When the monitor turns downward to a certain angle, it will draw in . Touch the “ ” ICON on touch screen to enter the setting mode, the message will display like following : FIG.6 Contrast Color TFT Monitor Adjustment Tint 16 In Radio mode, touch the“ ” icon or In media mode , touch the range to enter the home menu, the message like following as below.
Basic Operation SETTING WALLPAPER in wallpaper mode, you can select the among of “AUTO, GREEN, YELLOW, RED, LIGHT BLUE, BLUE, PINK ” . When you select the “AUTO” item, the player will change the background automatically . BASS: -7 to +7 Adjust bass level . BALANCE: R 0-10 to L 0-10 . Adjust sound balance between left and right speakers . FADE: F 0-10 to R 0-10 Adjust sound balance between front and rear speakers .
Basic Operation Setting Audio Mode In any modes, touch the “EQ” range on the touch screen (or press the EQ button on remote control) to select one of the preset sound modes: ROCK/POP/ JAZZ/CLASSIC/USER . The information will display in the monitor as follow : ROCK POP JAZZ USER CLASSIC It`s depend on your habit to select the Audio mode . Reset Factory Settings RESET button is placed on the housing and must be activated with either a ballpoint pen or thin metal object.
Control Panel UNIT KEYS 11 3 5 9 + 18 6 2 10 4 12 15 19 7 8 14 1 13 Control Panel 16 17 Sliding Pl ate di agram af ter remo ving Co ntrol Panel 1. OPEN or BUTTON To slide the monitor out and stand it up or into the monitor slot, press this button; To adjust the angle of the monitor, long press this button . 2. VOL KNOB & SEL BUTTON In normal mode, the VOL knob is used to increase or decrease the volume.
Control Panel 4/10. |<< and >>| BUTTONS In radio mode, Long pressing |<< or >>| button can automatically search down or up for an available station beginning from the current frequency; Briefly pressing |<< or >>| button can manually search down or up for a your desired station beginning from the current frequency.
Control Panel 11. (EJECT) BUTTON During disc playback, press this button to eject the disc. After the diss is ejected, press this button to draw the disc in again. 12. IR sensor 13. USB PORT and COVER 14. AUX IN JACK 15. LCD display 16. SD/MMC card slot 17.
Touch Screen Operation RADIO OPERATION Start Searching For a Station Listening to Radio Manual Search During Radio mode, briefly touch “ ” to increase frequency by one step of channel spacing. Briefly touch “ ” to decrease frequency by one step of channel spacing. Automatic Search During Radio mode, touch and hold (for more than 2 seconds ) either “ / ” ICONS to start search for a radio station automatically.
Touch Screen Operation >Keep the desired memory key pressed in until the station is heard again after a brief interruption . - Retrieve a preset station Touch the 1-6 ranges briefly to retrieve a station which had been stored in the memory in advance the chose number is shown on display . Automatic Memory Storing & Program Scanning DX ST USER SWF FM1 107.00 MHZ 5 CH 1 87.50 4 86.60 2 90.00 5 107.00 3 98.00 6 106.
Touch Screen Operation Media Operation In any modes, repeatedly press MOD button on front panel to enter the media play mode . The message will display as below : (When Parking Brake is applied .) To search the disc with numbers MENU PBC In Digital Video mode, touch to display the root menu. In VCD mode, touch to switch the PBC ON and PBC OFF.
Touch Screen Operation BASIC OPERATION Note: when the JPEG disc playback, in normal mode, you can use the cursor buttons to rotate the picture . Press UP to invert an image . Press DOWN to mirror an image . Press LEFT to rotate an image to left . Press RIGHT to rotate an image to right . Stopping Play Touch ICON to stop the unit playback. Touch to start play. Pause (still picture) Touch during playback to temporarily pause play. Touch again to return to normal playback.
Touch Screen Operation seconds part of each track/chapter on disc. (Touch it again to cancel this mode) FOR VCD : Touch the screen of the “INT” section (or longer press the 3/INT button on the remote control ).
Touch Screen Operation ON-SCREEN DISPLAY FUNCTION OSD During playback, touch the screen of the OSD section, it will display the following as below : 1. Digital Video: A.Touch or Press OSD for first time: 2.Example for VCD/SVCD/CD: A.Touch or Press OSD for first time: VCD TRK 1/19 A PBC C 0:01:36 B.Touch or Press OSD for second time: VCD TRK 1/19 A PBC C -0:06:06 Digital Video TT 01/01CH 04/31 C 0:02:06 C.
Touch Screen Operation Digital Video Special Function 1. Multi-subtitle Language Function (for Digital Video Only) 3. Multi-Angle Function (for Digital Video Only) During Digital Video playback. Touch the SUBTITLE section on touch screen(or press the SUBTITLE on the remote) . Each time the button is pressed or touch, number of the subtitle language changes in sequential order. During Digital Video playback, touch the ANGLE button on the touch screen .
Touch Screen Operation SYSTEM SETUP MEDIA SETUP MENU USING THE MENU SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE DEFAULT SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE DEFAULT NTSC PAL AUTO EXIT EXIT 1. IN disc model Touch the screen of “ ” range or press the SETUP button on remote . 2.The SETUP menu is displayed. 3.Touch directly the desired item to select the preferred item . Or by using the / / / buttons . 4. Touch the EXIT section to clear the setup menu or press the SETUP on the remote control .
Touch Screen Operation SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE DEFAULT 4:3PS 4:3LB 16:9 EXIT 16:9 4:3 Letter Box 4:3 Pan Scan TV TYPE SETUP This is to select the appropriate TV aspect (4:3 or 16:9) according to the connected TV set. Normal/PS (For 4:3 TV) Played back in the PAN & SCAN style. (If connected to wide-screen TV, the left and right edges are cut off.) Normal/LB (For 4:3 TV) Played back in LETTER BOX style.
Touch Screen Operation SYSTEM SETUP LANGUAGE SETUP ENGLISH GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG TV SYSTEM SCREEN SAVER TV TYPE DEFAULT RESTORE EXIT EXIT DEFAULTS Selecting the DEFAULT item and confirming RESTORE will return ALL personal settings you have made, including radio and TV presets, to the factory default settings. AUDIO LANGUAGE SETUP Select the preferred AUDIO soundtrack language by touching directly the desired language .
Touch Screen Operation VIDEO SETUP LANGUAGE SETUP OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG ENGLISH GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN 12 10 8 6 4 2 0 BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS EXIT EXIT DISC MENU LANGUAGE SETUP Select the preferred DISC MENU language by touching directly the desired language . CONTRAST- the contrast of the video signal (the dark portions of pictures).
Touch Screen Operation DIGITAL SETUP VIDEO SETUP 12 10 8 6 4 2 0 BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS DIGITAL SETUP DYNAMIC RANGE FULL 6/8 4/8 2/8 OFF EXIT EXIT SATURATION- the saturation of the video signal (the vividness of the color) all above can be adjusted to your tasters . DYNAMIC RANGE CONTROL Select DRC and adjust the dynamic range of a Dolby Digital encoded program. There are 8 steps between full compression and off compression.
Touch Screen Operation AUX Operation On the front panel of this unit, there is an AUX IN jack, follow the diagram below to connect analogue replay devices(only for the Audio connect, if you want to connect the Video, please plug the RCA
Touch Screen Operation BT OPERATION IMPORTANT: 1. “Pair” To Your BT Phone Prior to using the Car Kit for the fist time, you must pair it with a BT-enabled mobile handset. The following steps describes pairing the instruction for a typical BTenabled mobile handset. 1). Place the Car Kit and mobile handset in 3 meters apart. 1). If the pairing can not be completed within approximately 2 minutes , whiles the pairing mode is activated, and you will need to reattempt pairing (See steps 2-5 above) . 2).
Touch Screen Operation ANSWER A CALL After you hear the ring tone, a incoming telephone number will display on the TFT monitor . Touch the screen of “ ” range to listen or press the “PAIR/ ” button shortly on the remote control . PLAY BT MUSIC In BT mode, repeatedly the MOD on the panel to select the “BT MUSIC” Mode .
Touch Screen Operation Changing From DISC to USB Playback Mode If the disc present in the player is an Digital Video or VCD or MP3/WMA or MP4 disc, touch the screen of the “ ” range to enter the home menu, then touch the “USB” ICON to enter the USB mode . USB OPERATION Following the diagram below, connect your USB device to the front panel USB port . If it is properly connected, the device will be mounted and start playing automatically.
Touch Screen Operation SD/MMC card OPERATION The unit can support playback MP3/WMA/JPEG/MP4 and Divx format which are stored into SD and MMC memory card . Please read below before you start the operation of memory card . INSERTING THE SD OR MMC CARD . Label side facing upward Press REL button to detachable the panel Insert the memory card into slot with label side facing upward . Note: the mini card slot for GPS only. Press in till heard a “CLICK” REMOVING THE SD OR MMC CARD .
Touch Screen Operation MP3/WMA/JPEG/MPEG4 PLAY The unit is support MP3/WMA/JPEG/MPEG4 . When a disc is inserted into player, the following picture will appear on the monitor . The unit will play the first track automatically . You can touch to directly others mode (MP3/JPEG /MPEG4) to play . EX. : when the MP3 mode is selected . 2 1 Current type (highlighted bar) . [MP3] ITLE / SONG: TRACK 03 / 2 Current track (ID3 TAG display) . 001 WMA 002 1 Mp3 003 3 The current play mode(MP3).
Specification Generall : Supply Voltage: Current Consumption: Signal System: Discs Played: 12V DC (11V-15V) Less than10 A Compositive video 1.
Trouble Shooting Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. SYMPTOM No power CAUSE SOLUTION The car ignition switch is not on The fuse is blown If the power supply is properly connected to the car accessory terminal,switch the ignition key to "ACC" Replace the fuse Presence of disc inside the Remove the disc in the player, then put a new one player.
