Please read this manual carefully before operation PRECAUTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER ( OR BACK ), NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ! The lightning flash with arrowhead symbol within an equilateral triangle Is intended to alert the user to the presence of uninsulated “dangerous” Voltage “within the product’enclosure that may be of sufficient magnitude To constitute a risk of electric shock.
PRECAUTIONS Follow the advice below for safe operations. ON PROTECTION AGAINST LASER ENERGY EXPOSURE • As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the casing. • Stop operation immediately if any liquid or solid object should fall into the cabinet. • Do not touch the lens or poke at it. If you do, you may damage the lens and the player may not operate properly. • Do not put anything in the safety slot.
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions - All the safety and operating instructions should be read before the appliance is operated 2. Keep these instructions - The safety and operating instructions should be kept for future reference. 3. Heed all warnings - All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow all instructions - All operation and use instructions should be followed. 5.
COMPLIANCE WITH FCC REGULATIONS This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules . These limits are designed to provide reasonable protection against harmful interference in a residential installation .This equipment generates , uses ,and can radiate radio frequency energy and ,if not installed and used in accordance with the instructions , may cause harmful interference to radio communication .
CD CARE & MAINTENANCE Handling CDs Holds a CD by its edges .Avoid touching the recorded side of the disc .To remove a CD from its storage case , press down on the center retention mechanism of the case and lift the disc , Cleaning the CDs Use a dry cloth to wipe off any fingerprints and dusts from the playing surface of the disc .Wipe in a straight line radially from the center to the outside edge of the disc . Small dusts particles light stains will not affect playback quality .
20. RIGHT SPEAKER JACK 21. LEFT SPEAKER JACK 22. WALL MOUNTING SLOT FUNCTIONS AND CONTROLS Remote Control 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. POWER TRACK+10 ID3 MENU ENTER► STOP PROGRAM PLAY MODE FM.
CONNECTIONS Speakers ◆ Connect the black wire of the left speaker to the black terminal marked “L-“on the rear of the main unit . ◆ Connect the white wire of the left speaker to the red terninal marked”L+” on the rear of the main unit. ◆ Connect the black wire of the right speaker to the black terminal marked “R-“ on the rear of the main unit . ◆ Connect the white wire of the right speaker to the red terminal marked”R+” on the rear of the main unit. Power This unit runs on AC 120V power . 1.
Basic Operation 1. Press FUNCTION repeatedly to select CD mode. 2. To open the CD Door ,press the CD open button on the top of the unit. Insert a CD with its label facing up.Close the CD Door (it will click into place) 3. The CD will automatically play after reading the disc. CD Functions Play/Pause/Stop ◆ Press ENTER ► during playback to pause .Press ENTER ► again to resume playback . ◆ Press STOP during playback to stop the disc . Scan through the current track ◆ Press and hold FM.
DRM-encrypted WMA files are not supported. Basic Operation ◆ Press FUNCTION to select USB or SD CARD mode . ◆ Connect a USB drive containing MP3/WMA files to the USB port or SD/MMC CARD to the SD/MMC CARD slot on the bottom side of the unit. Playback will start automatically. ◆ Press ENTER ► to pause playback or press STOP to stop playback completely . Press ENTER ► again to resume playback . ◆ Press FM.ST or BAND to select the previous or next track ,respectively .
PROGRAM PLAY OPERATION Program a sequence of up to 20 tracks to be played . IN CD disc mode 1. Press STOP to make sure playback is stopped . 2. Press PROGRAM PLAY MODE button to enter program mode .The LCD screen will display 『MEMORY』, 『P01』and flashing 『00』. 3. While 『00』is blinking , press FM.ST or BAND to select a track number ,and then press PROGRAM PLAY MODE button to store it in memory . The LCD will display 『P02』. 4. Repeat the previous step untill you have selected up to 20 tracks .
MENU FUNCTION TIMER (AUTOMATICAL POWER ON ) 1. Press MENU on the remote control repeatedly until the LCD screen displays “TIMER” , press ENTER ► to enter to set the TIMER . Press FM.ST or BAND to select the TIMER ON, then press ENTER ► to set the timer . . 2.. Hour digit will flash , press FM.ST or BAND to set the hour . press ENTER ► to confirm . 3. The minute digit will flash , press FM.
Basic Operation 1. Use a 3.5mm male to male line in cable (included) to connect the Line-out or Headphone out jack of an audio device to this system Auxiliary Line-In jack. 2. Press POWER to turn the player on . 3. Set the FUNCTION Mode switch to the “AUX” position . 4. Start playback on the external audio device. ◆ You must use the external audio device to control playback. ◆ To avoid distortion, do not set the volume from the external audio device to very high levels.
Playback is “skipping” ◆ Ensure that the CD is not damaged ,scratched ,or dirty. ◆ Ensure that the unit has been installed in a stable location to avoid vibration and shock . The player will only play one track ,repeatly . ◆ Ensure that REPEAT mode is off (press REPEAT to cancel ). The function mode is not working . ◆ Ensure that the CD Compartment Lid is closed . The Function mode is not working . ◆ Ensure that the CD Compartmetn Lid is closed .