User Manual

Page 6
FREQ.-UMSCH.
TAST TAST TAST
NOT-RUF
T T0
I
T T0
®
MA DE I N GE R MA NY
®
ZULASSUNG - TYPE APPROVAL - AGREMENT - HOMOLOGATION
I
SYSTEM
NON EU COUNTRIES:
AUS
CDN
CH
CZ
H
IS
KO
N
EU COUNTRIES:
X0560
no approval necessary
2634 231 116A /
2634 231 116
BAKOM 95.0720.K.P
45251983
MÜ-40.039-083/96
IS-3236-00
93335
NO96000433-R /
NO95000545-R
1027/ 96
YK33-9806
K9VPOC90 T001 /
K9VPNN3-5R001 /
O5RS-DE96AO
3K43D/3R1B9/
SPLS/RX-439/98
PL
TJY
USA
ZA
1
2
3
4
5
TYPE:
SERIAL NO.:
HF MODULE:
FREQUENCY:
PNN -BUS -3
999 899 4990
S-EM01A0
BAND F
7. FUNCTION CHECK
Frequency change Pocket-V-3 :
Frequency change Pocket-V-3 :
Frequency change Pocket-V-9:
ACCIDENT RISK!
STOP EMERGENCY STOP check
Checking theLED's at thereceiver PNN-BUS-3:
LED1:
LED2:
LED3:
LED4:
LED5:
-Version1
By unlocking the button switch the power supply of the transmitter is released. To change
the frequency, press the switch "HORN/FREQUENCY CHANGE" briefly in the direction of
thesymbol"FREQUENCY CHANGE".
After about 8 seconds the frequency change can be checked by pressing the switch
"HORN/FREQUENCY CHANGE" in thedirectionof thesymbol"HORN":
If the receiver locks into the new frequency, a horn signal is given (if present) and the unit
tobe controlled is readyfor operation.*
-Version2
By unlocking the button switch the power supply of the transmitter is released. The unit to
be controled is switched on by the switch "ON/HORN". With this a horn signal (if present)is
released at the unit to be controlled and the unit is ready for operation.
To ch ange the frequency, press th e switch "ON /HORN/ FREQUENC Y CHAN GE" brie fly in
thedirectionof thesymbol "FREQUENCYCHANGE".
After about 8 seconds the receiver has to be made ready to operate by pressing the
switch "ON/HORN/FREQUENCY CHANGE" in the direction of the symbol "ON/HORN" and
checked ifthe frequencyhas beenchanged:
If the receiver locks into the new frequency, a horn signal is given (if present) and the unit
tobe controlled is ready for operation.*
To change the f requency, press the swi tch "FR EQUEN CY C HAN GE".
After about 8 seconds the frequency change can be checked by pressing the switch
"HORN/EMERGENCY CALL":
If the receiver locks into the new frequency, a horn signal is given (if present) and the unit
tobe controlled is readyfor operation.*
*Pleaseobservetheparticularpostalapprovalregulationsoftheconcernedcountry.
To m ain tain operatio nal safety, a regular fu ncti on ch eck of the NBB radio remote control is
necessary. In single-shift day-to-day operation, we recommend performing this check at
least once a week. Checking is possible using the display lights provided on the receiver.
To do so, the transmitter mus t be s et to the ready-to-o per ate state.
First connect just the receiver - the transmitter remains switched off.
Activate the transmitter by unlocking the EMERGENCY STOP switch, resp. pres-
sing the key "ON/HORN" (Pocket-A, -B).
Now check the commands (always start with the lowest stage) and check for cor-
rect reaction of the unit to be controlled.
Ensure in particular that there is nobody in the danger area.
,resp. .PresstheEMERGENCYSTOPswitchat
the transmitter until the switch engages, resp. press the STOP key. Then observe
if the unit to be controlled is switched off (time to switch off according to the appli-
cation).
POWER ON. If LED fails to come on, check the power supply.
If the power lead is OK, call in the after-sales service.
HF PRESENT. Steady light when transmitter is switched on
(insignificant for scanner operation).
Flashes evenly during fault-free operation.
Irregular flashing means that the HF channel is probably at fault -
please set another channel.
If this LED comes on, the HF channel is at fault.
Charge condition display of battery (only present when charger is
integrated). Steady light when charging a battery.
LED flashes: The battery is charged, the charging process is finished.
%
%
%
%
%
%
%
%
%
%