Quick Start Guide

ManualsBrandsNec ManualsDigital Signage DisplaysMultiSync V984Q 98" LED-backlit LCD display 4K - for digital signage

NEC Display Solutions of America, Inc.

V984Q/C981Q Installation Guide [Ver.1.0]

www.necdisplay.com V984Q/C981Q Page 1 of 12

Contents:

Product Description and Notes Page 1

Rotation Page 1

Ventilation Recommendations Page 2

Carrying Handle Positioning Page 2

Display Dimensions

Front, Top, Right Side, Left Side, Bottom Page 3

Back Side Page 4

Display Dimensions with stand Page 5

Optional Stand Dimensions Page 6

Optional Wall Mount Dimensions Page 7

Optional Speaker Dimensions (SP-TF1) Page 8

Compute Module Integration Page 9

Input Panel Page 10

ASCII Commands Page 10

Control Codes Page 11

Cable Connection Page 11

Browser Control Page 12

Product Description:

Type: LCD Display

Resolution: 3840 x 2160 Dimensions without stand: 86.4” (W) x 49.2” (L) x 3.7” (D)

Aspect Ratio: 16:9 Dimensions with stand: 86.4”(W) x 50.6”(H) x 23.9”(D)

EMI: Class B Weight without stand: 204.8 lbs. / 92.9kg

Power Consumption: 525W (Max C981Q), 650W (Max V984Q) Weight with stand: 214.5 lbs. / 97.3kg

BTU’s: 1791.37 BTU/hour (C981Q), 2217.89 BTU/hour (V984Q)

NOTES:

• This document is intended to be used as a reference guide to supply useful information for a design or installation. It is not intended to be

a step-by step procedure for installation.

• Any ceilings or walls must be strong enough to support the monitor and the installation must be in accordance with any local

building codes. All mounts should make secure contact to wood studs.

• Distances are in inches, for millimeters multiply by 25.4.

• Distances may vary ±5%.

Tilt Angle and Rotation:

• Below is the maximum angle the monitor can be tilted. Note that the monitor can only be tilted in the landscape position.

Summary of content (12 pages)

PAGE 1
NEC Display Solutions of America, Inc. V984Q/C981Q Installation Guide [Ver.1.
PAGE 2
NEC Display Solutions of America, Inc. Ventilation Recommendations: Dimensions below are minimum required for proper ventilation. NOTE: • The ventilation space should not be covered or closed off at the front of the opening. If for some reason the opening needs to be covered, other means of ventilation will need to be incorporated into the design. Contact NEC for design review and recommendations. Carrying Handle Positioning: www.necdisplay.
PAGE 3
NEC Display Solutions of America, Inc. Display Dimensions: www.necdisplay.
PAGE 4
NEC Display Solutions of America, Inc. Display Dimensions (cont.): NEC strongly recommends using size M8 screws (15-17mm + the thickness of the bracket and washers in length). If using screws longer than 15-17mm, please check the depth of the hole. www.necdisplay.
PAGE 5
NEC Display Solutions of America, Inc. Display Dimensions (with optional ST-801 stand): www.necdisplay.
PAGE 6
NEC Display Solutions of America, Inc. Table Top Stand Dimensions (ST-801): www.necdisplay.
PAGE 7
NEC Display Solutions of America, Inc. Optional Large Wall Mount (WMK-6598): Optional Standard Wall Mount (WMK-3257): www.necdisplay.
PAGE 8
NEC Display Solutions of America, Inc. Optional Speaker Dimensions (SP-TF1) www.necdisplay.
PAGE 9
NEC Display Solutions of America, Inc. Compute Module Integration: • • Door on the back of the display can be opened by loosening captive screws. Separate IO Board is necessary to accompany RPi Compute Module in unit www.necdisplay.
PAGE 10
NEC Display Solutions of America, Inc. Input Panel: Bottom Side (Rotated) ASCII Common Commands: • This monitor supports common ASCII control commands with many other NEC projectors. For more information on this, please see our website. www.necdisplay.
PAGE 11
NEC Display Solutions of America, Inc. Control Codes: NOTE: Contact your NEC representative for codes not listed. Cable Connection Communication Protocol: Interface: Communication System: Baud Rate: Data Length: Parity: None Stop Bit Communication Code: 1 bit ASCII Interface: Communication System: Communication Layer: IP Address: Port Number: Ethernet (CSMA/CD TCP/IP (Internet Protocol Suite) Transport layer (TCP) 192.168.0.10 (default out of box) 7142 (Fixed) www.necdisplay.
PAGE 12
NEC Display Solutions of America, Inc. Browser Control: Information and control can also be available through the HTTP browser control menu. In order to accomplish this, type: http:///pd_index.html Note that the LAN Power needs to be turned on in order for the display to be controlled while the units are off. All displays are set to the IP address 192.168.0.10 out of the box Communicating network PC needs to be on the same subnet as display that is being communicated with www.