MultiSync 97F Flat MultiSync 77F /97F ® MS77F97F112701.
Index Warning .................................................................................................. 1 Contents ............................................................................................... 2 Quick Start ...........................................................................................3 Controls ................................................................................................ 5 Recommended Use .............................................................
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
Contents Your new NEC MultiSync® monitor box* should contain the following: • MultiSync Monitor MultiSync 77F or 97F • Power Cord • Captive Signal Cable • User’s Manual Captive Signal Cable Power Cord User’s Manual MultiSync 97F Flat MultiSync 77F /97F ® TM TM * Remember to save your original box and packing material to transport or ship the monitor. 2 MS77F97F112701.
Quick Start To attach the MultiSync® monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. If necessary, install the display card into your system. For more information, refer to the display card manual. 3. For the PC: Connect the 15-pin mini D-SUB of the captive signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws.
Quick Start –continued Mac Adapter (Not Included) 15-pin mini D-SUB Captive Signal Cable Figure B.1 Power Outlet Power Cord Figure C.1 Figure D.1 Power Button 4 MS77F97F112701.
Controls OSM™ (On-Screen Manager) control buttons on the front of the monitor function as follows: SELECT Enters and exits the OSM menu. CONTROL –/+ Selects one of the controls and increases or decreases the adjustment. RESET Resets the highlighted control to the factory setting. Press –/+ at the same time for approximately one second. Adjusts the overall image and background screen brightness. Adjusts the image brightness in relation to the background.
Controls –continued Increases or decreases the curvature of the sides either to the left or right. Rotates the entire display clockwise or counterclockwise. Degauss Control: Eliminates the buildup of stray magnetic fields that alter the correct scan of the electron beams and affect the purity of the screen colors, focus and convergence. When activated, your screen image will jump and waver a bit as the screen is demagnetized.
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC® COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water.
Recommended Use –continued CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 12 inches and no further away than 28 inches from your eyes. The optimal distance is 18 inches.
Specifications Monitor Specifications MultiSync® 77F Monitor Picture Tube Diagonal: Viewable Image Size: Input Signal Video: Sync: Display Colors Synchronization Range 17 inch 16.0 inch 90° deflection, 0.21-0.25 mm variable horizontal dot pitch, 0.24-0.28 mm variable diagonal dot pitch, medium short persistence phosphor, multi-layered, anti-static screen coating, semi-tint screen, Invar Shadow Mask and OptiClear® screen. ANALOG 0.7 Vp-p/75 Ohms Separate sync. TTL Level Horizontal sync.
Specifications –continued Monitor Specifications MultiSync® 97F Monitor Picture Tube Diagonal: Viewable Image Size: Input Signal Video: Sync: Display Colors Synchronization Range 19 inch 18.0 inch 90° deflection, 0.20-0.24 mm variable horizontal mask pitch, 0.24-0.28 mm variable diagonal mask pitch, medium short persistence phosphor, multi-layered, antistatic screen coating, semi-tint screen, Invar Shadow Mask and OptiClear® screen. ANALOG 0.7 Vp-p/75 Ohms Separate sync. TTL Level Horizontal sync.
Features Flat Dot Pitch CRT: Delivers an unparalleled viewing experience with a virtually flat image, eliminating distortion and reducing glare so that what you see onscreen is what you get on your printed output. OptiClear® Screen Surface: Reduces reflection and glare and increases contrast without sacrificing focus level, clarity or brightness. Along with the flat square technology CRT, a high contrast screen delivers crisp, clean text and graphics.
Troubleshooting No • • • • picture Display card should be completely seated in its slot. Power Button and computer power switch should be in the ON position. Signal cable should be completely connected to display card/computer. Check connector for bent or pushed-in pins. Image is scrolling or unstable • Signal cable should be completely attached to the computer. • Check pin assignments and signal timings of the monitor and your display card with respect to recommended timings and pin assignments.
References • BBS (978) 742-8706 NEC-Mitsubishi Electronics Display of America Remote Bulletin Board System is an electronic service accessible with your system and a modem. Communication parameters are: 300/1200/2400/9600/14.4k/28.8k/33.
Limited Warranty NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit which proves defective for a period of one (1) year from the date of first consumer purchase. Spare parts are warranted for ninety (90) days.
AVERTISSEMENT AFIN D’ÉVITER TOUT RISQUE D’INCENDIE OU D’ÉLECTROCUTION, NE PAS EXPOSER CET APPAREIL À LA PLUIE OU À L’HUMIDITÉ. NE PAS UTILISER LA FICHE D’ALIMENTATION POLARISÉE AVEC UNE PRISE DE CORDON DE RALLONGE OU AUTRE PRISE SAUF SI LES BROCHES PEUVENT ÊTRE ENTIÈREMENT INTRODUITES. NE PAS OUVRIR LE BOÎTIER, LEQUEL CONTIENT DES COMPOSANTS À HAUTE TENSION. CONFIER TOUS TRAVAUX À DU PERSONNEL TECHNIQUE QUALIFIÉ.
Contenu La boîte* de votre nouveau moniteur NEC MultiSyncMD contient : • Moniteur MultiSync MultiSync 77F au 97F • Cordon d'alimentation • Câble de signal captif • Manuel de l'utilisateur Câble de signal captif Cordon d'alimentation Manuel de l’utilisateur MultiSync 97F Flat MultiSync 77F /97F ® TM TM * Ne pas oublier de conserver la boîte et le matériel d'emballage d'origine pour transporter ou expédier le moniteur. 16 MS77F97F112701.
Mise en marche rapide Pour raccorder le moniteur MultiSyncMD au système, suivre les directives ci-après : 1. Mettre l'ordinateur hors tension. 2. Si nécessaire, installer la carte vidéo dans le système. Pour plus d'informations, se reporter au mode d'emploi de la carte vidéo. 3. Pour le PC : Connecter la mini-fiche D-SUB à 15 broches du câble de signal captif au connecteur de la carte vidéo du système (Figure A.1). Serrer toutes les vis.
Mise en marche rapide (suite) Adaptateur Mac (non fourni) Mini-fiche D-SUB à 15 broches Câble de signal captif Figure B.1 Prise de courant Cordon d’alimentation Figure C.1 Figure D.1 Bouton d’alimentation 18 MS77F97F112701.
Commandes Les touches de commandes OSMMC (Gestionnaire à l'écran) à l'avant du moniteur fonctionnent comme suit : SELECT Entre et quitte le menu OSM. CONTROL –/+ Déplace la barre dans le sens – ou + pour augmenter ou diminuer le réglage. RESET Réinitialise la commande en surbrillance au réglage d’usine. Appuyez simultanément sur les boutons – et + pendant environ 1 seconde. Règle la luminosité de l'image générale et de l'écran d'arrière-plan. Règle la luminosité de l'image en function du fond.
Commandes (suite) Commande Degauss : Élimine l'accumulation de champs magnétiques parasites qui modifieraient le balayage correct du faisceau d'électrons et affecteraient la pureté des couleurs de l'écran, la netteté et la convergence. Lorsque l'image d'écran est activée, celle-ci saute et tremble un peu pendant la démagnétisation de l'écran. Attention : Prière de laisser s'écouler un minimum de 20 minutes entre chaque utilisation de la commande Degauss.
Usage recommandé Consignes de sécurité et de maintenance POUR UN FONCTIONNEMENT OPTIMAL, PRIÈRE DE NOTER CE QUI SUIT POUR LE RÉGLAGE ET L'UTILISATION DU MONITEUR COULEUR MultiSyncMD : • NE PAS OUVRIR LE MONITEUR. Aucune pièce intérieure ne nécessite l'intervention de l'utilisateur, et l'ouverture ou la dépose des couvercles peut exposer à des risques de décharges dangereuses ou d'autres risques. Confier tous travaux à du personnel technique qualifié.
Usage recommandé (suite) LA MODIFICATION DE LA POSITION ET DU RÉGLAGE DU MONITEUR PEUT RÉDUIRE LA FATIGUE DES YEUX, DES ÉPAULES ET DE LA NUQUE. OBSERVER LES DIRECTIVES CI-APRÈS LORS DU POSITIONNEMENT DU MONITEUR : • Régler la hauteur du moniteur de sorte que le dessus de l'écran soit au niveau ou légèrement en-dessous du niveau des yeux. Les yeux doivent regarder légèrement vers le bas lorsque l'on regarde le milieu de l'écran.
Fiche techniques Caractér. techn. du moniteur Tube cathodique Diagonal : Format de l'image visible : Signal d'entrée Vidéo : Sync : Horizontale: Verticale : 17 po 16,0 po Déflexion de 90°, espacement entre pixels variable horizontal 0,21mm - 0,25 mm; espacement entre pixels variable diagonal 0,24mm - 0,28 mm; luminophore à persistance moyenne-courte; revêtement d’écran multicouche antistatique; masque perforé d'invar et surface d’écran OptiClear ®.
Fiche techniques (suite) Caractér. techn. du moniteur Tube cathodique Diagonale : Format de l'image visible : Signal d'entrée Vidéo : Sync : Horizontale: Verticale : 19 po 18,0 po Déflexion de 90°, 0,20-0,24 mm masque variable horizontal tangue; 0,24-0,28 mm masque variable diagonal tangue; luminophore à persistance moyenne-courte; revêtement d’écran multicouche antistatique; masque perforé d'invar et surface d’écran OptiClear ®. Nombre illimité de couleurs Dépend de la carte vidéo utilisée.
Fonctions CRT de Point Plat Tangue: Assure une qualité de visualisation inégalée avec une image quasiplate, éliminant la distorsion et réduisant les reflets de sorte que ce que vous voyez à l’ecran est identique à ce qui est imprimé sur paper. Surface d'écran OptiClear® : Réduit la réflexion et l'éblouissement et augmente le contraste sans sacrifier le niveau de netteté, la clarté ni la luminosité.
Dépannage Pas d'image • La carte vidéo doit être complètement introduite dans sa fente. • La touche d'alimentation et le commutateur d'alimentation de l'ordinateur doivent être en position ON (Marche). • Le câble de signal doit être bien connecté à la carte vidéo /l'ordinateur. • Vérifier si le connecteur n'est pas plié ou si les broches ne sont pas renfoncées. L'image défile ou est instable • Le câble de signal doit être bien fixé à l'ordinateur.
Références • BBS (978) 742-8706 Le système de babillard électronique NEC-Mitsubishi Electronics Display of America, Inc. est un service électronique accessible avec votre système et un modem. Les paramètres de communication sont : 300/1200/2400/9600/1,4 k/28,8 k/33,6 k bps, pas de parité, 8 bits de données, 1 bit d'arrêt • Service à la clientèle/ Assistance technique (800) 632-4662 Télécopieur (978) 742-7049 • Canaux électroniques: Internet (e-mail): tech-support@necmitsubishi.com Site internet ftp: ftp.
Garantie limitée NEC-Mitsubishi Electronics Display of America, Inc. (ci-après «NMD-A») garantit que ce produit est exempt de vice de fabrication et de main-d’oeuvre et, selon les conditions énoncées ci-dessous, accepte de réparer ou remplacer, à sa discrétion, toute pièce de l’appareil concerné qui s’avérerait défectueuse et ce, pendant une période de une (1) ans à partir de la date d’achat initial. Les pièces de rechange sont garanties pendant quatre-vingt dix (90) jours.
MD Série Flat Enterprise NEC Série MultiSync NEC AVIS DE PROPRIÉTÉ EXCLUSIVE ET DE DÉGAGEMENT DE RESPONSABILITÉ Les informations contenues dans ce document, y compris tous les designs et matériel s'y rapportant, sont la propriété de NEC-Mitsubishi Electronics Display of America et/ou ses concédants.
NEC MultiSync® Series PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC-Mitsubishi Electronics Display of America and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use and sales rights thereto, except to the extent said rights are expressly granted to others.