User’s Manual E552 E462 E422 E322
Index Precautions And Reminders ���������������������������������������������������������������� English-1 Important Safety Instructions ��������������������������������������������������������������� English-2 Safety Instructions ������������������������������������������������������������������������������� English-4 Important Information �������������������������������������������������������������������������� English-5 Declaration Of Conformity ����������������������������������������������������������
Do not place the display in confined spaces or in a box when in use. Maintain ample ventilation for the display when in use. Do not open the display cabinet. Call a NEC certified service personnel for any internal service needed for your display. Keep the display away from direct sunlight, dust, humidity, and smoke. Unplug immediately if any foreign object is put in the display or if the display falls.
Important Safety Instructions Read before operating equipment The lamps in this product contain mercury. Please dispose according to state, local or federal law. Follow all warnings and instructions marked on this display. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8.
NOTE: To the display system installer: This reminder is provided to call attention to Article 820-44 of the National Electric Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the facility, as reasonably close to the point of cable entry as possible Power source This LCD display operates on 120 volts 60 Hz, AC current. Insert the power cord into a 120 volts 60 Hz outlet.
Safety Instructions FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications.
English Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
Batteries installed warning Caution - Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
English Installed with stand 11 7/8 inches 30 cm 4 inches 10 cm 4 inches 10 cm Leave at least this space around the set. 4 inches 10 cm Never install the TV set where Air circulation is blocked. Objects and ventilation holes Never push objects of any kind into the TV through the cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or an electric shock. Do not place any objects on the TV.
Declaration Of Conformity This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: Address: Tel. No.: Type of Product: Equipment Classification: Model: NEC Display Solutions of America, Inc.
If necessary, the user should contact the dealer or an experienced radio/ television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio-display Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4. Windows is a registered trademark of Microsoft Corporation.
Preparation IMPORTANT: Do not apply pressure to the screen display area which may compromise the integrity of the display. The manufacturer’s warranty does not cover user abuse or improper installations. Preparing Your LCD Display For Wall Mounting We suggest that you keep your display at least 2.36 inches (60 mm) from the wall to prevent cable interference. Before mounting your display on the wall, you need to remove the base.
E322 / E422 / E462 English Attaching the Base E552 1. Place the display face down on a soft and flat surface to prevent scratching and damage. 2. Carefully align the base to the stand and fasten the screws with a crosshead screwdriver. CAUTION: The base of the stand is very heavy. Install with care to avoid injury such as dropping the base onto one's foot. Place The Display On A Solid Surface Ensure that the LCD display is placed in a position to allow free flow of air.
Battery Installation and Replacement The remote control is powered by two 1.5V AAA batteries. To install or replace batteries: 1. Open the battery cover of the remote control by pushing and pulling it in the direction of the arrow. 2. Insert two new “AAA” size batteries for the remote control. When replacing old batteries, push them towards the springs and lift them out. 3. Match the batteries to the (+) and (-) marks in the battery compartment. 4.
The display should be installed close to an easily accessible power outlet. Fully insert the prongs into the power outlet socket. A loose connection may cause image degradation. If there is power to the display, the front LED at the bottom of the display will be either blue or red. A blue LED means the display is powered on. A red LED means the display is in standby mode.
Source Connection Guide E322/E422/E462 E322/E462 E422 AC POWER 7 3 8 9 1 ® 2 5 4 6 1 English-14
English E552 AC POWER 6 7 5 4 8 1 2 9 1. HDMI – Connect the primary source for digital video such as a DVD multimedia player or set top box through this all digital connector. 2. RGB/AUDIO – Connect the video and audio cables from a computer here. 3. AV – Connect the primary source for composite video devices, such as a VCR or video game. Use the white and red connectors to connect the external audio from the same source. 4.
8. USB/SERVICE – Insert USB storage device to view photos and listen to the music. /This USB slot is for future software upgrades. 9. RS-232C – Input from external equipment such as a PC or AV control system in order to control RS-232C functions. Once your AV device is connected, press the Source button on the remote control to select the relevant source to view. (ex: Press COMP button to select “Component” if you have connected a source to the Component input.
E322/E422/E462 English Operating Instructions E552 1 2 5 6 3 1 4 2 5 3 6 4 7 7 Using The Side Panel Controls 1. VOL + Press to increase the volume. Press this key to shift Right in the OSD menu. 2. VOL - Press to decrease the volume. Press this key to shift Left in the OSD menu. 3. CH ▲/ Press to increase the channel number. Press this key to shift up in the OSD menu. 4. CH ▼/ Press to decrease the channel number. Press this key to shift down in the OSD menu. 5.
Using The Remote Control Power Press to turn On/Off (standby) the power. (Note: To completely turn off the power, unplug the AC cord from the power outlet.) COM P TV Press to choose ATSC/NTSC tuner source mode. AV Press to choose Composite source mode. PRE CH COMP Press to choose Component source mode. HDMI/PC Press repeatedly to choose PC IN or HDMI source mode. 0 ─ 9 / - number Press to enter the tuner channel number to select channel (Press ‘-’ to choose the sub-channel).
EPG Press to display the Electronic Program Guide in TV mode. It shows the current channel name, program name, time, rating, and summary, depending on the information provided by the broadcaster. Freeze Press to freeze the displayed picture. MTS Press to activate the NTSC tuner sounds such as Stereo, SAP, Monotone, and languages of the digital tuner. Wide Press to choose the display aspect ratio: Wide Screen/4:3/Panorama/ Zoom/Automatic/Dot by Dot. (Ratio availability varies by video inputs.
Navigating The On-Screen Menu Press the Menu button to display and Exit to close the main menu. Use the Navigation Ring to navigate, select, adjust or confirm an item on the OSD (On Screen Display) menu. Note: Some features may only be available in a particular source mode. Video Menu This menu adjusts video items.
Audio Menu The Audio menu provides an audio adjustment for user to modify the audio setting. Video Audio TV Setup Parental Balance 0 Bass 50 Treble 50 Equalizer Off Speaker On SPDIF Type Auto Volume Control PCM Off USB OK Enter Select EXIT Exit 1. Balance Audio balance adjustment, the tuning range is -50 ─ 50. 2. Bass Control the bass tone from 0 ─ 100. (The default of 50 is enabled) 3. Treble Control the treble tone from 0 ─ 100. (The default of 50 is enabled) 4.
TV Menu The channel menu sets your signal source options. Video Audio Tuner Mode Cable Setup Menu The Setup menu in TV mode is shown below. According to various requirements in different source modes, certain features could be hidden (disabled) on the menu. Channel Scan Channel Skip TV Setup MTS Stereo Audio Language English Video Parental Audio USB TV Enter Select EXIT Exit Parental 1. Tuner Mode Select TV source signal from the air (antenna) or cable (CATV). 2.
• Window Color: Choose one of the display windows color. • Window Opacity: Select one of the display windows color. 6. Location Select from Store or Home mode. Store mode is recommended for displaying in a retail showroom, and Home mode is recommended for normal home use for Energy Saving. 7. Version Info Display the software information. 8. Reset Restore all the default Setup settings. English-23 English [Sleep Timer] Set a time when the TV switches to standby automatically.
Parental Menu User has to key in the four digit password before entering the Parental Control sub-menu. User can modify the restricted table after entering the parental sub-menu. While exiting the sub-menu, the parental control function is activated. Video Password **** Audio TV Setup Parental USB EXIT Back 1. Password Enter the password to access the parental sub menu. Note: • The default password is [0000].
This feature is useful for viewing still pictures and listening to the music on USB Drives via the USB slot on the side your NEC display. You can access the USB menu by pressing Source button on the remote control. This can also be accessed through the OSD main menu under the category “MultiMedia”. Note: • 1. Basic Operation Using the remote control’s cursor, navigate through thumbnails to individually select pictures you would like to view.
2. View Photos Use the navigation cursor to select the photo and press OK to view a full screen image. • Buttons for enlarged photo display operation 4. USB device compatibility Buttons Descriptions OK Play or pause the slide show CH +/Go to the previous/ next photo in the same directory. Red Open the photo submenu Green Select the slide show duration. Yellow Select the slide show transition effect. Exit Return to the previous operation. 3.
Care Of The Screen Do not rub or strike the screen with anything hard as this may scratch, mar, or even damage the screen permanently. Unplug the power cord before cleaning the screen. Dust the display by wiping the screen and the cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean, damp cloth. Do not use liquid cleaners, aerosol cleaners, or solvents of any kind.
Product Specification This model complies with the specifications listed below. Reorient or relocate the receiving display. Designs and specifications are subject to change without notice. This model may not be compatible with features and/or specifications that may be added in the future.
E322 E422 E462 E552 188 W 365 W 2 x 10 W 2 x 10 W POWER Power Consumption 105 W Standby < 1W Power AC 120V, 60Hz 180 W AUDIO POWER Power Consumption 2 x 5W 2 x 10 W OPERATING ENVIRONMENT Temperature 0°C ─ 40°C / 32°F ─ 104°F Humidity 10% ─ 85% Height 3000m STORAGE ENVIRONMENT Temperature -10°C ─ 50°C / 14°F ─ 122°F Relative Humidity 5% ─ 85% Absolute Air Humidity 1─25 g/m3 Max. Change of Temp. 0.5°C/min (max.
Before Calling Service Please make these simple checks before calling service. These tips may save you time and money as charges for receiver installation and adjustments of customer controls are not covered under your warranty. Symptoms Items To Check And Actions To Follow “Ghost ” or double image when using the tuner • This may be caused by an obstruction to the antenna due to high rise buildings or hills. Using a highly directional antenna may improve the picture.
HDTV HDTV displays are technically defined as being capable of displaying a minimum of 720p or 1080i active scan lines. HDMI Inputs High-Definition Multimedia Interface Audio / Video Inputs are located on the rear of the receiver. These connectors are used for the input of audio and video signals. Designed to receive higher picture resolution and offer sound connection options. Menu An on-screen listing of features shown on the display screen is made available for user adjustments.
Limited Warranty NEC Display Solutions of America, Inc. (hereinafter “NEC DISPLAY SOLUTIONS”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NEC DISPLAY SOLUTIONS’ sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase.
NEC Monitor Customer Service & Support Customer Service and Technical Support Parts and Accessories (800) 632-4662 (888) 634-4662 Fax (800) 695-3044 Warranty Information www.necdisplay.com Online Technical Support www.necdisplay.com Sales and Product Information Sales information Line (888) 632-6487 Canadian Customers (866) 771-0266, Ext#: 4037 Government Sales (800) 284-6320 Government Sales email gov@necdisplay.com Electronic Channels http://www.necdisplay.com Product Registration http://www.necdisplay.