User’s Manual E461 E551
Index Precautions And Reminders...............................................................English-1 Important Safety Instructions..............................................................English-2 Safety Instructions..............................................................................English-4 Important Information.........................................................................English-5 Declaration Of Conformity..................................................................
Do not place the display in confined spaces or in a box when in use. Maintain ample ventilation for the display when in use. Do not open the display cabinet. Call a NEC certified service personnel for any internal service needed for your display. Keep the display away from direct sunlight, dust, humidity, and smoke. Unplug immediately if any foreign object is put in the display or if the display falls.
Important Safety Instructions Read before operating equipment Follow all warnings and instructions marked on this display. 1. Read and keep these instructions. 2. Obey all warnings. 3. Follow all instructions. 4. Do not use equipment near water. 5. Clean with dry cloth. 6. Do not block any of the ventilation areas. Install in accordance with the manufacturer’s instructions. 7. Do not install near heat sources, including radiators, heat registers, stoves, or any other apparatus that creates heat. 8.
NOTE: To the display system installer: This reminder is provided to call attention to Article 820-44 of the National Electric Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the facility, as reasonably close to the point of cable entry as possible Power source This LCD display operates on 120 volts 60 Hz, AC current. Insert the power cord into a 120 volts 60 Hz outlet.
Safety Instructions FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications.
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not supplied with this equipment, please contact your supplier. Plug Type North America Plug Shape Region Voltage U.S.A./Canada AC 120 V Apparatus shall not be exposed to dripping, splashing or any objects filled with liquids. Batteries installed warning Caution - Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type.
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: NEC Display Solutions of America, Inc. Address: 500 Park Boulevard, Suite 1100 Itasca, Illinois 60143 Tel. No.
• Increase the separation between the equipment and display. • Connect the equipment into a different outlet than the receiver. • Consult your dealer or an experienced radio/display technician for assistance. If necessary, the user should contact the dealer or an experienced radio/ television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and Resolve Radio-display Interference Problems.
IMPORTANT: Do not apply pressure to the screen display area which may compromise the integrity of the display. The manufacturer’s warranty does not cover user abuse or improper installations. Preparing Your LCD Display For Wall Mounting We suggest that you keep your display at least 2.36 inches (60 mm) from the wall to prevent cable interference. Before mounting your display on the wall, you need to remove the base.
Antenna Connection Unless your LCD display is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best television performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient. When using a 75-Ohm coaxial cable system, connect the CATV coaxial cable to the AIR/CABLE (75-Ohm) terminal.
The display should be installed close to an easily accessible power outlet. Fully insert the prongs into the power outlet socket. A loose connection may cause image degradation. If there is power to the display, the front LED at the bottom of the display will be either blue or red. A blue LED means the display is powered on. A red LED means the display is in standby mode.
USB/ SERVICE Source Connection Guide RGB RGB AC POWER R L VIDEO S-VIDEO HDMI 3 HDMI 4 AUDIO E461/E551 AV 2 HDMI – Connect the primary source for digital video such as a DVD multimedia player or set top box through this all digital connector. 2. RGB/AUDIO – Connect the video and audio cables from a computer here. 3. AV/S-VIDEO – Connect the primary source for composite video devices, such as a VCR or video game. Use the white and red connectors to connect the external audio from the same source.
VOL 1 2 CH 3 4 MENU 5 INPUT 6 E.SAVE 7 POWER 8 Using The Side Panel Controls 1. VOL + Press to increase the volume. 2. VOL - Press to decrease the volume. 3. CH + Press to increase the channel number. 4. CH - Press to decrease the channel number. 5. MENU Press to open or exit the OSD (On-Screen Display) menu. 6. INPUT Press to select the input source. 7. E-SAVE Press to set power consumption reduction based on three levels (Min, Medium, Max). 8.
Using The Remote Control Power Power Press to turn On/Off (standby) the display. (Note: To completely remove power from the display, remove the AC cord from the display.) Video Video Press repeatedly to choose AV1/AV2 source mode. Comp Press repeatedly to choose Component 1/Component 2 source mode. Comp PC/HDMI TV 1 2 3 4 5 6 7 8 9 0 PREV CH Sleep Freeze MTS/SAP Fav PC/HDMI Source EPG Mute Press repeatedly to choose VGA or HDMI source mode.
Switch the sound On/Off. Press to show the information about the input source, tuner channel, display resolution and current time. Press to choose the display aspect ratio: Auto/4:3/16:9/Full/Zoom1/ Zoom2. (Ratio availability varies by video inputs. Refer to the Picture Format Table below for details.) CH- / CH + V-Chip Info Press + or - to browse through the tuner channels (or input sources when in source mode). VOL- / VOL+ Press to temporarily lock the parental control.
Navigating The On-Screen Menu 1. Press the Menu/Exit button to display or close the main menu. 2. Use the Navigation Ring to navigate, select, adjust or confirm an item on the OSD (On Screen Display) menu. Press the Menu/Exit button to enter/ exit the main OSD. Adjust the items including Video, Audio, Setup, Channels and Multimedia. NOTE: Some features may only be available in a particular source mode. Video Menu This menu adjusts video items.
The Audio menu provides an audio adjustment for user to modify the audio setting. Video Audio Sound Mode Standard Treble 32 Bass 32 Setup Balance Channels Preferred Language 0 Audio Language Multimedia Move Digital Output ENT Select MENU Return English English 1 PCM EXIT Exit 1. Sound Mode Adjust the sound mode by choosing one of the preset sound modes: Custom, Standard, Movie, or News. 2. Treble Control the treble tone from 0 ~ 63. (The default of 32 is enabled) 3.
3. Sleep Timer Select the auto turn off time from 5 minutes to 4 hours. 4. Parental Controls Provides the parental control (V-chip) function setting. Before entering the Parental Control submenu, user must first key in the password. Enabling the Parental Locks feature allows the user to modify the restriction table as it relates to MPAA or TV ratings. Once the user adjusts and exits the sub menu the parental control function activates.
[Retail] mode is intended for showroom or shop use. Any adjustment in this mode will not be saved even when display’s AC power is lost. [Off-Timer] – Turns off the display if no remote control functions are recieved in a three hour period. 11. Light Control [Power LED] – Allows for the power LED to be turned off in low ambient light environments. 12. Transparency: Adjust the transparency of the on-screen menu from 0 to 10. 13.
Channel Menu Multimedia The channel menu sets your signal source options. This feature is useful for viewing still pictures on USB Drives via the USB slot on the side your NEC display. Upon inserting a USB drive into the USB slot, you will be prompted to view these photos with the JPEG viewer feature. This can also be accessed through the OSD main menu under the category “multimedia”. Using the remote control’s cursor, navigate through thumbnails to individually select pictures you would like to view.
English Tips Care Of The Screen Do not rub or strike the screen with anything hard as this may scratch, mar, or even damage the screen permanently. Unplug the power cord before cleaning the screen. Dust the display by wiping the screen and the cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean, damp cloth. Do not use liquid cleaners, aerosol cleaners, or solvents of any kind.
Product Specification This model complies with the specifications listed below. • Reorient or relocate the receiving display. • Designs and specifications are subject to change without notice. • This model may not be compatible with features and/or specifications that may be added in the future.
Power Consumption 210 W 240 W Standby <1W Power AC 120V, 60Hz AUDIO POWER 2 x 15 W ENVIRONMENTAL TEMPERATURE 0°C - 40°C / 32°F - 104°F STORAGE ENVIRONMENT Temperature -10°C - 50°C / 14°F - 122°F Relative Humidity 5% ~ 85% Absolute Air Humidity 1 ~ 25 g/m3 Max. Change of Temp 0.5°C/min (max. 10°C/30min) Air Pressure 700~1060 mbar (70~106Kpa) Raditiation Solar Heat 700 W/m2 PACKAGE CONTENTS Supplied Accessories 1x TV Unit 1x Power Cord 1x Stand Base 1x Remote Control 2x 1.
Before Calling Service Please make these simple checks before calling service. These tips may save you time and money as charges for receiver installation and adjustments of customer controls are not covered under your warranty. Symptoms Items To Check And Actions To Follow “Ghost ” or double image when using the tuner * This may be caused by an obstruction to the antenna due to high rise buildings or hills. Using a highly directional antenna may improve the picture.
HDTV HDTV displays are technically defined as being capable of displaying a minimum of 720p or 1080i active scan lines. HDMI Inputs High-Definition Multimedia Interface Audio / Video Inputs are located on the rear of the receiver. These connectors are used for the input of audio and video signals. Designed to receive higher picture resolution and offer sound connection options. Menu An on-screen listing of features shown on the display screen is made available for user adjustments.
Limited Warranty NEC Display Solutions of America, Inc. (hereinafter “NEC DISPLAY SOLUTIONS”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NEC DISPLAY SOLUTIONS’ sole option) any part of the enclosed unit which proves defective for a period of two (2) years from the date of first consumer purchase.
NEC Monitor Customer Service & Support Customer Service and Technical Support Parts and Accessories (800) 632-4662 (888) 634-4662 Fax (800) 695-3044 Warranty Information www.necdisplay.com Online Technical Support www.necdisplay.com Sales and Product Information Sales information Line (888) 632-6487 Canadian Customers (866) 771-0266, Ext#: 4037 Government Sales (800) 284-6320 Government Sales email gov@necdisplay.com Electronic Channels http://www.necdisplay.com Product Registration http://www.
Manuel d’utilisation E461 E551
Index Consignes de sécurité......................................................................Français-1 Déclaration de conformité ...............................................................Français-2 Informations importantes .................................................................Français-4 Mises en garde et rappels................................................................Français-6 Importantes consignes de sécurité...................................................
DÉCLARATION DE LA FCC Cet équipement a été testé et déclaré conforme aux limites de la Classe B d’appareils numériques, selon l’alinéa 15 de la réglementation de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nocives en milieu résidentiel. Cet équipement génère et utilise, et peut émettre de l’énergie de fréquence radio et, s’il n’est pas installé et utilisé selon les instructions, peut produire des interférences nuisibles aux communications radio.
Déclaration de conformité Cet appareil est conforme à l'alinéa 15 des réglementation de la FCC. Son utilisation est soumise aux deux conditions suivantes. (1) Cet appareil ne doit pas produire des interférences nuisibles et (2) cet appareil doit accepter toute interférence reçue, notamment toute interférence pouvant affecter son fonctionnement. Responsable États-Unis : NEC Display Solutions of America, Inc. Adresse : 500 Park Boulevard, Suite 1100 Itasca, Illinois 60143 Tel. No.
• • • Réorienter ou déplacer l’antenne de réception. Accroître la distance entre l’équipement et l’écran. Connecter l’équipement à une prise sur un circuit différent de celui auquel le récepteur est connecté. • Consulter le revendeur ou un technicien radio/écran expérimenté pour obtenir de l’aide.. Si nécessaire, l'utilisateur doit s'adresser au revendeur ou à technicien radio/télévision expérimenté pour obtenir des conseils supplémentaires.
Informations importantes AVERTISSEMENT POUR PRÉVENIR LES INCENDIES OU CHOCS ÉLECTRIQUES, N'EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À L'HUMIDITÉ. DE PLUS, N'UTILISEZ PAS LA FICHE POLARISÉE DE L'APPAREIL AVEC UNE RALLONGE, UNE EMBASE OU D'AUTRES PRISES À MOINS QUE LES BROCHES PUISSENT ÊTRE TOTALEMENT INSÉRÉES. ABSTENEZ-VOUS D'OUVRIR LE COFFRET CAR CELUI-CI CONTIENT DES COMPOSANTS À HAUTE TENSION. FAITES APPEL À UN TECHNICIEN QUALIFIÉ POUR LES RÉPARATIONS.
Type de prise Amérique du Nord Forme de prise Région Tension U.S.A./Canada CA 120 V Ne pas exposer l’appareil à des gouttes, des éclaboussures ou à tout objet rempli de liquide. Avertissement concernant l’installation des batteries Mise en garde - Danger d’explosion si les batteries ne sont pas remplacées correctement. Ne les remplacez que par des batteries identiques ou de type équivalent. N’exposez pas les batteries à une chaleur excessive sous risque d’explosion.
Mises en garde et rappels Placez l'écran sur une surface solide et plane. Débranchez l'écran immédiatement en cas de chute. Ne recouvrez et ne bloquez pas les évents ou ouvertures. Une ventilation inadéquate peut raccourcir la durée de vie de l'écran et provoquer une surchauffe Débranchez l'appareil immédiatement en cas de dysfonctionnement, par exemple, la perte du signal audio/vidéo, la présence de fumée, ou si une mauvaise odeur se dégage de l'écran. Interdisez/Évitez d'ouvrir le boîtier de l'écran.
À lire avant d'utiliser l'équipement Follow all warnings and instructions marked on this LCD display. 1. Lisez ces instructions. 2. Conservez ces instructions. 3. Respectez tous les avertissements. 4. Suivez toutes les instructions. 5. N'utilisez pas cet équipement près de l'eau. 6. Nettoyez cet équipement uniquement avec un chiffon sec 7. Ne bloquez pas les ouvertures de ventilation. Installez l'équipement selon les instructions du fabricant. 8.
17. Une antenne extérieure ne doit pas être située à proximité de lignes électriques aériennes ou d'autres circuits électriques. 18. Si une antenne extérieure est connectée au récepteur, assurez-vous que le système d'antenne est mis à la terre pour fournir une protection contre les surtensions et l'accumulation de charges statiques. L'article 810 du Code électrique national, ANSI/NFPA No.
IMPORTANT : n’appliquez pas de pression sur la zone d’affichage de l’écran, ce qui pourrait compromettre l’intégrité de l’affichage. La garantie du fabricant ne couvre pas les abus de l’utilisateur ou les installations inadaptées. Préparation de votre écran LCD à un montage mural Nous vous recommandons de maintenir l’écran à au moins 2,36 pouces (60 mm) du mur pour prévenir les interférences de câble. Avant de monter l’écran sur le mur, vous devez retirer le pied.
Connexion de l’antenne À moins que votre écran LCD soit connecté à un système de TV par câble ou à un système d’antenne centralisé, une bonne antenne de télévision couleur extérieure est recommandée pour obtenir les meilleurs résultats possibles. Cependant, si vous êtes situé dans une zone de réception de signal exceptionnellement bonne, qui est dépourvue d’interférence et d’images fantômes multiples, une antenne intérieure peut suffire.
L’écran doit être installé à proximité d’une prise de courant facilement accessible. Insérez entièrement les broches dans la prise de courant. Une connexion lâche peut entraîner une dégradation de l’image. Si l'écran est alimenté, le voyant avant situé au bas de l'écran est bleu ou rouge. Le voyant est bleu lorsque l'écran est allumé. Le voyant est rouge lorsque l'écran est en veille.
USB/ SERVICE Guide de connexion à une source RGB RGB AC POWER ALIMENTATION SECTEUR R L VIDEO S-VIDEO HDMI 3 HDMI 4 AUDIO E461/E551 AV 2 HDMI : branchez la source vidéo numérique principale (par ex. lecteur DVD multimédia ou boîtier décodeur) à l'aide de ce connecteur 100 % numérique. 2. RVB/AUDIO : sert à brancher les câbles vidéo et audio d'un ordinateur. 3. AV/S-VIDÉO : branchez la source principale de dispositifs vidéo composite, comme un magnétoscope ou un jeu vidéo.
VOL 1 2 CH 3 4 MENU 5 INPUT 6 E.SAVE 7 POWER 8 Utilisation des commandes du panneau latéral 1. VOL + Appuyez pour augmenter le volume. 2. VOL - Appuyez pour diminuer le volume. 3. CH + Appuyez pour augmenter le numéro de canal. 4. CH - Appuyez pour diminuer le numéro de canal. 5. MENU Appuyez pour ouvrir ou quitter le menu OSD (affichage sur l’écran). 6. INPUT Appuyez pour sélectionner la source d’entrée. 7.
Utilisation de la télécommande POWER Appuyez pour allumer/éteindre (veille) l’écran. (Remarque : pour couper complètement l’alimentation de l’écran, débranchez le cordon CA de l’appareil.) Power Video Video Appuyez plusieurs fois pour choisir le mode de source AV1/AV2. Comp Appuyez plusieurs fois pour choisir le mode de source Component 1/ Component 2 (Composante 1/ Composante 2. PC/HDMI Appuyez plusieurs fois pour choisir le mode de source VGA ou HDMI.
“<”,“>”,“”,“v”, ENTER” Appuyez pour régler les diverses fonctions du menu. Cette fonction n’est pas prise en charge. Mute Sert à mettre ou enlever le son. Info Appuyez pour afficher les informations sur la source d’entrée, le canal du syntonisateur, la résolution de l’affichage et l’heure actuelle. CH- / CH + Appuyez sur + ou - pour parcourir les canaux du syntonisateur (ou les sources d’entrée en mode source). VOL- / VOL+ Appuyez sur + ou - pour régler le volume.
Navigation dans le menu à l’écran 1. Appuyez sur le bouton Menu/ Exit pour afficher ou fermer le menu principal 2. Utilisez l’anneau de navigation pour naviguer, sélectionner, régler ou confirmer un élément sur le menu OSD (Affichage sur l’écran). Appuyez sur le bouton Menu/Exit pour entrer dans le menu OSD principal. Réglez les paramètres tels que Vidéo, Audio, Configuration, Canaux et Multimédia. REMARQUE : certaines fonctions ne sont parfois disponibles que dans un mode de source particulier.
Il permet à l'utilisateur de modifier la configuration audio. Video Audio Sound Mode Standard Treble 32 Bass 32 Setup Balance Channels Preferred Language 0 Audio Language Multimedia Move Digital Output ENT Select MENU Return English English 1 PCM EXIT Exit 1. Sound Mode Réglez le mode de son en choisissant l’un des modes de son présélectionnés : Personnalisé Standard, Film ou Actualités. 2. Treble Réglez les aigus de 0 à 63. (La valeur par défaut de 32 est activée) 3.
[Mode horaire] : choisissez Auto ou Manuel. [Fuseau horaire] : établissez le fuseau horaire actuel. [Heure d’été] : choisissez On ou Off. 3. Sleep Timer Sélectionnez le délai d’arrêt automatique de 5 minutes à 4 heures. 4. Parental Controls Permet de configurer la fonction de contrôle parental (V-chip). Pour entrer dans le sous-menu de contrôle parental, l’utilisateur doit d’abord taper le mot de passe.
[Background Opacity] :(Opacité de l’arrière-plan) Automatique/Continu/Clignotant/ Transparent/Translucide. [Edge Effet] : (Effet de bord) Automatique/Aucun/ Surélevé/ Abaissé/Uniforme/Ombre à gauche/Ombre à droite. [Edge Color] : (Couleur de bord) Automatique/ Rouge/Vert/ Bleu/Jaune/Magenta/Cyan/Noir/ Blanc. 10. Energy Options Profitez des fonctions d’économie d’énergie de cet écran.
Menu Canal Le menu Canal configure vos options de source de signal. Video Audio Source Cable Signal Strength New Channel Scan Setup Add Channels to List Channels Channel List Channel Labels Multimedia Move Favorite Channels ENT Select MENU Return EXIT Exit 1. Source Sélectionnez le signal de la source TV entre antenne et câble (CATV). 2. Signal Strength Montre l’intensité du signal de syntonisateur numérique reçu. 3.
Entretien de l’écran Ne frottez pas l’écran avec un objet dur, car cela pourrait rayer, marquer ou même endommager l’écran de manière permanente. Débranchez le cordon d’alimentation avant de nettoyer l’écran. Époussetez l’écran et le coffret avec un chiffon propre et doux. Si l’écran nécessite un nettoyage supplémentaire, utilisez un chiffon propre humide. N’utilisez jamais de produits nettoyants, d’aérosols ou de solvants.
Caractéristiques du produit Ce modèle est conforme aux caractéristiques indiquées ci-dessous. • Réorienter ou déplacer l'antenne de réception. • Les conceptions et caractéristiques sont sujettes à des modifications sans préavis. • Ce modèle pourra ne pas être compatible avec des fonctions et/ou caractéristiques éventuelles ajoutées à l'avenir.
Consommation électrique 210 W Veille <1W Alimentation CA 120 V, 60 Hz 240 W Puissance audio 2 x 15 W Température ambiante 0 °C - 40 °C / 32 °F - 104 °F Environnement d’entreposage Température -10 °C - 50 °C / 14 °F - 122 °F Humidité relative 5% ~ 85% Humidité absolue de l’air Changement maxi de température Pression atmosphérique Chaleur solaire de rayonnement 1 ~ 25 g/m3 0.5°C/min (max.
Avant d’appeler le service d’assistance Veuillez faire les simples vérifications suivantes avant d’appeler le service après-vente. Ces conseils peuvent vous permettre d’économiser du temps et de l’argent, puisque les frais d’installation de récepteur et de réglage des commandes du client ne sont pas couverts par votre garantie.
Entrée S-Vidéo Vous pouvez brancher votre écran à une source vidéo haute résolution (par ex. un magnétoscope Super VHS, un lecteur de disques laser ou un système de cinéma maison DVD) afin de fournir le meilleur affichage possible. Entrées HDMI Les entrées Audio / Vidéo High-Definition Multimedia Interface sont situées à l’arrière du récepteur. Ces connecteurs sont utilisés pour l’entrée des signaux audio et vidéo.
Limited Warranty NEC Display Solutions of America, Inc. (ci-après « NEC-DISPLAY SOLUTIONS ») garantit ce Produit contre les vices de fabrication et de matière et, conformément aux conditions citées ci-après, s’engage à réparer ou à échanger (à la seule discrétion de NEC-DISPLAY SOLUTIONS) toutes les pièces de l’appareil concerné reconnues comme étant défectueuses durant une période de deux (2) an, à partir de la date du premier achat. Les pièces de rechange sont garanties quatre-vingt dix (90) jours.
NEC Monitor Customer Service & Support Service à la clientèle et assistance technique du moniteur NEC Pièces et accessoires (800) 632-4662 (888) 634-4662 Fax (800) 695-3044 Informations sur la garantie www.necdisplay.com Assistance technique en ligne www.necdisplay.com Informations commerciales et produit Ligne d’informations commerciales (888) 632-6487 Clients au Canada (866) 771-0266, Poste 4037 Ventes au gouvernement (800) 284-6320 E-mail du service de ventes au gouvernement gov@necdisplay.