Desktop Monitor MultiSync EA245WMi User’s Manual Please find your model name in the label on the backside of monitor.
Index Warning, Caution ..........................................................................................................................English-1 Registration Information ...............................................................................................................English-2 Recommended use ......................................................................................................................English-3 Safety Precautions and Maintenance ................................
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
Registration Information FCC Information 1. Use the attached specified cables with this monitor so as not to interfere with radio and television reception. (1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A., and meet the following condition. Power supply cord Non shield type, 3-conductor Plug shape U.S.A (2) 2. Please use the supplied shielded video signal cable.
Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 40 cm (15.75 inches) and no further away than 70 cm (27.56 inches) from your eyes.
English Contents For contents, please refer to the contents sheet. Quick Start To attach the Base to the LCD stand: 1. Place monitor face down on a non-abrasive surface (Figure 1). 2. Please rotate the stand 90 degrees as shown in Figure 1. NOTE: Handle with care when pulling the stand. 3. Attach the base to the stand and lock screw at the base’s bottom (Figure 2). NOTE: Reverse this procedure if you need to re-pack the monitor.
3. Place hands on each side of the monitor to tilt the LCD panel 30-degree angle and lift up to the highest position. 4. Connect all cables to the appropriate connectors (Figure C.1). When using the USB cable, connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the computer (Figure C.1a). If using the cord from a USB device, plug into the downstream port of the monitor.
NOTE: Please refer to Caution section of this manual for proper selection of AC power cord. 8. Turn on the computer and the monitor by touching the power key on the front bezel (Figure E.1). 9. No Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup.
Tilt and Swivel Grasp the top and bottom sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1). Figure TS.1 NOTE: Handle with care when tilting the monitor screen. Do not insert hand into tilt cover when adjusting the monitor screen tilt. Flexible Arm Installation This LCD monitor is designed for use with a flexible arm. To prepare the monitor for alternate mounting purposes: • Follow the instructions provided by the manufacturer of the display mount.
This LCD monitor is designed for use with a flexible arm. 1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand. 2. Using the specified 4 screws, attach the arm to the monitor (Figure F.1). Spring washer 12 mm Flat washer Thickness of Bracket (Arm) 2.0~3.2 mm 100 mm 100 mm Weight of LCD assembly: 4.2 kg Figure F.1 Caution: Use ONLY 4 pieces M4 sized specified screws when mounting to avoid damage to the monitor and stand.
ControlSync 1. Connect the master monitor with a sub monitor via a ControlSync cable (ø 2.5) into ControlSync IN/OUT. 2. Follow the steps of DATA COPY. When the setting of the master monitor is adjusted, it will be copied and sent to the connected sub monitor(s) automatically. 3. Up to 24 sub monitors can be daisy-chained via ControlSync. NOTE: Connect the master monitor via ControlSync OUT connector. ControlSync icon The ControlSync icon will appear on the upper left of the OSD menu in the sub monitor.
You can connect multiple monitors by using DisplayPort daisy-chain connection. For using as multiple monitors in MST (multi-stream transport) mode, setting should be DP OUT MULTISTREAM “AUTO” at each connected monitor. Please change the monitor setting which is connected to a computer last in the connected monitors. If monitors have no image, turn off the monitor who is connected to a computer then turn it on. Some DisplayPort configuration may be required. Please refer below and set as required.
Recovering from no image If monitors have no image after setting DP OUT MULTISTREAM, please set as follows: 1. Turn off the computer. 2. Touch the “MENU” key to show the No Signal OSD menu. 3. Touch the “ ” key to show VIDEO INPUT menu. 4. Touch “ ” or “ ” to show to set the DisplayPort switch menu. 5. Select DP VER “1.1” to switch the DisplayPort setting. 6. Touch MENU to close the OSD menu. 7. Turn on the computer.
OSD (On-Screen Display) control keys on the front of the monitor function are as follows: To access OSD menu, touch any of the control keys. To change signal input, touch the SELECT key. NOTE: Exit OSD in order to change signal input. 1 Ambient Light Sensor Human Sensor Detects the level of ambient lighting and the presence of a user, allowing the monitor to make adjustments to various settings resulting in a more comfortable viewing experience. Do not cover this sensor.
ECO MODE Decreases the amount of power consumption by reducing the brightness level. OFF: No function. 1: Sets brightness variable range from 0% to 60%. This setting can adjust brightness to a range in which power is reduced by 20% compared to the maximum brightness setting. 2: Sets brightness variable range from 0% to 30%. This setting can adjust brightness to a range in which power is reduced by 35% compared to the maximum brightness setting.
Adjusts the threshold level of human sensing. When the human icon is located on the right side of the white color bar or vermilion color wave, a person is not detected. NOTE: Once the OSD has been closed, Human sensor starts to work. START TIME (HUMAN SENSING) Adjusts the wait time of entering to low brightness mode or power saving mode when Human Sensor detects no person. DV MODE Dynamic Visual Mode allows you to select from the following settings: STANDARD: Standard setting.
FINE (Analog input only) Improves focus, clarity and image stability by increasing or decreasing this setting. If the “Auto Adjust” function and the “H.SIZE” function do not give you a satisfactory picture setting, a fine tuning can be performed by using the “FINE” function. For this a Moiré test pattern could be used. If the Fine value is wrongly calibrated, the result would look like the left drawing. The image should be homogeneous. When FINE value is wrong. When FINE value is correct.
Color Control System: Color presets are available for adjusting color settings. (sRGB and NATIVE color presets are standard and cannot be changed). 1, 2, 3, sRGB, 5: Increases or decreases Red, Green or Blue color depending upon which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown by the bars. sRGB mode dramatically improves the color fidelity in the desktop environment by a single standard RGB color space.
POWER SAVE TIMER POWER SAVE TIMER allows the monitor to turn off automatically after continuing power saving mode for 2 hours. LED BRIGHTNESS You can adjust the blue LED brightness. DDC/CI This function allows the DDC/CI function ON or OFF. USB POWER Selects a power relation of USB. AUTO: Power is supplied to USB downstream port depending on related power condition. ON: Power is always supplied to USB downstream port even when in power save mode or power OFF.
To initiate data copy from the master monitor to the sub monitor(s), select “DATA COPY” and touch “SELECT”. A “PROCEEDING...” indicator will appear on the screen. NOTE: This function is only intended for the master monitor in ControlSync. All of the settings specified in the ControlSync chart (see page 10) will be copied from the master monitor to the sub monitor(s). CUSTOMIZE SETTING Store the current settings for easy recovery. To store current settings: Touch “SELECT”.
Specifications Monitor Specifications MultiSync EA245WMi Notes LCD Module 61.13 cm/24 inches 61.13 cm/24 inches 1920 x 1200 Active matrix; thin film transistor (TFT) liquid crystal display (LCD); 0.270 mm dot pitch; 300 cd/m2 white luminance; 1000:1 contrast ratio (typical), (5000:1 Contrast ratio, Dynamic). Digital RGB DisplayPort Complies with Standard V1.
DisplayPort: DisplayPort is designed to be the future-ready and scalable solution for high performance digital display connectivity. It enables the highest resolutions, the fastest refresh rates and deepest color depths over standard cables. DisplayPort OUT: This monitor has a DisplayPort out connector for daisy-chain connection. Multiple monitors can be connected without complicated cable management.
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • The monitor does not support DisplayPort converter adapter. • When you use DisplayPort signal, check to make sure not to plug the input signal cable in DisplayPort out connector. • Power Switch and computer power switch should be in the ON position.
• Make certain the computer is not in a power-saving mode (touch the keyboard or mouse). • Some display cards do not output video signal when monitor is turned OFF/ON or disconnect/connect from the AC power cord under low resolution with DisplayPort. • When using an HDMI input, please change “OVER SCAN”. No Sound • Make sure the speaker cable is proper connected. • Check to see if mute is activated. • Check the volume in the OSD menu.
Using the Zoom Function Allows you to use the entire screen area, significantly expanding the size. Allows the picture displayed in the center to expand. SETUP 1. Select FULL or ASPECT in EXPANSION to activate the Zoom function (see page 16). EXPANSION OFF 2. Set a resolution via H.RESOLUTION or V.RESOLUTION (see page 16). Vertical expansion Horizontal expansion 3.
English Human sensing function Human sensing function reduces power consumption by detecting the movement of a person. The HUMAN SENSING has following two settings: MODE HUMAN SENSING SETTING No person in front of the monitor LIGHT 1 BRIGHTNESS 0% DEEP 2 Power saving mode Image of human sensing operation A. When the sensor detects no person in front of the monitor, the monitor stays on for a period of time which is set at HUMAN SENSING > START TIME (see page 15). B.
Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient lighting within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions.
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentallyfriendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).
