MultiSync EA294WMi User’s Manual
Index Warning, Caution ..........................................................................................................................English-1 Registration Information ...............................................................................................................English-2 Recommended use ......................................................................................................................English-3 Contents ..........................................................
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
Registration Information Canadian Department of Communications Compliance Statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information 1. Use the attached specified cables with the MultiSync EA294WMi (L292VK) monitor so as not to interfere with radio and television reception.
Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 40 cm (15.75 inches) and no further away than 70 cm (27.56 inches) from your eyes.
English Contents Your new NEC monitor box* should contain the following: • MultiSync monitor with a tilt/swivel/pivot/height adjust stand • Power Cord*1 • Video Signal Cable (DVI-D to DVI-D cable)*2 • Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) • USB Cable • Audio Cable (ø 3.5 stereo mini plug) • ControlSync Cable (ø 2.
Quick Start To attach the Base to the LCD stand: 1. Place monitor face down on a non-abrasive surface (Figure 1). NOTE: Handle with care when monitor facing down, for avoiding damage to the front control keys. 2. Please rotate the stand 90 degrees as shown in Figure 1. NOTE: Handle with care when pulling the stand. Figure 1 3. Attach the base to the stand and lock screw at the base’s bottom (Figure 2). NOTE: Control keys Screws Reverse this procedure if you need to re-pack the monitor.
4. Connect all cables to the appropriate connectors (Figure C.1). When using the USB cable, connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the computer (Figure C.1a). If using the cord from a USB device, plug into one of the downstream ports of the monitor. NOTE: Incorrect cable connections may cause abnormal operation, damage display quality/components of LCD module and/ or shorten the module’s life.
8. Turn on the computer, then turn on the monitor by pressing the power sign on the front bezel (Figure E.1). 9. No Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup. For further adjustments, use the following OSD controls: • AUTO CONTRAST (Analog input only) • AUTO ADJUST (Analog input only) Refer to the Controls section of this User’s Manual for a full description of these OSD controls.
Grasp the top and bottom sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1). Figure TS.1 NOTE: Handle with care when tilting the monitor screen. Flexible Arm Installation This LCD monitor is designed for use with a flexible arm. To prepare the monitor for alternate mounting purposes: • Follow the instructions provided by the manufacturer of the display mount.
Mount Flexible Arm This LCD monitor is designed for use with a flexible arm. 1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand. 2. Use the 4 screws removed from the stand to attach the arm to the monitor (Figure F.1). Caution: Use ONLY the screws (4 pcs) that were removed from the stand to avoid damage to the monitor or stand.
OSD (On-Screen Display) control keys on the front of the monitor function are as follows: To access OSD menu, touch any of the control keys. To change signal input, touch the SELECT key. NOTE: Exit OSD in order to change signal input. 1 AmbiBright Sensor Human Sensor Detects the level of ambient lighting, allowing the monitor to make adjustments to various settings resulting in a more comfortable viewing experience. Do not cover this sensor. 2 LED Indicates that the power is on or off.
ECO TOOLS BRIGHTNESS Adjusts the overall image and background screen brightness. If ECO MODE is set to 1 or 2, a bar for CARBON FOOTPRINT will appear. CONTRAST Adjusts the overall image and background screen brightness by input signal level. ECO MODE Decreases the amount of power consumption by reducing the brightness level. OFF: No function. 1 (ENERGY STAR SETTING): Sets brightness variable range from 0% to 60%.
The human sensor on the front side of the monitor detects the movement of a person by using the HUMAN SENSING function. The HUMAN SENSING has three settings: OFF: No HUMAN SENSING. 1 (LIGHT): After it is detected that there is no person after a period of time, the monitor shifts to low brightness mode automatically to reduce the power consumption. When a person comes near the monitor again, the monitor will automatically return to normal mode. START TIME adjusts the wait time to react.
FINE (Analog input only) Improves focus, clarity and image stability by increasing or decreasing this setting. If the “AUTO ADJUST” function and the “H.SIZE” function do not give you a satisfactory picture setting, a fine tuning can be performed by using the “FINE” function. For this a Moiré test pattern could be used. If the FINE value is wrongly calibrated, the result would look like the left drawing. The image should be homogeneous. When FINE value is wrong. When FINE value is correct.
Color Control System: Color presets select the desired color setting. 1, 2, 3, 5: Increases or decreases Red, Green or Blue color depending upon which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown by the bars. NATIVE: Original color presented by the LCD panel that is unadjustable. sRGB: sRGB mode dramatically improves the color fidelity in the desktop environment by a single standard RGB color space.
RESPONSE IMPROVE Turns the Response Improve function on or off. Response Improve may reduce blurring that occurs in some moving images. OFF TIMER Monitor will automatically power down when you have selected a pre-determined amount of time. Before powering off, a message will appear on the screen asking if you want to delay the turn off time by 60 minutes. Touch any OSD key to delay the power-down time.
To initiate data copy from the master monitor to the sub monitor(s), select “DATA COPY” and touch “SELECT”. A “PROCEEDING...” indicator will appear on the screen. NOTE: This function is only intended for the master monitor in ControlSync. All of the settings specified in the ControlSync chart (see page 26) will be copied from the master monitor to the sub monitor(s). CUSTOMIZE SETTING Store the current settings for easy recovery. To store current settings: Touch “SELECT”.
Specifications Monitor Specifications MultiSync EA294WMi Notes LCD Module 73.02 cm/28.7 inches 73.02 cm/28.7 inches 2560 x 1080 Active matrix; thin film transistor (TFT) liquid crystal display (LCD); 0.263 mm dot pitch; 300 cd/m2 white luminance; 1000:1 contrast ratio (typical), (25000:1 Contrast ratio, Dynamic). DisplayPort Connector: Digital RGB DisplayPort Complies with Standard V1.
DisplayPort: DisplayPort is designed to be the future-ready and scalable solution for high performance digital display connectivity. It enables the highest resolutions, the fastest refresh rates and deepest color depths over standard cables. MHL: MHL (Mobile High Definition Link) is designed for a mobile audio/video interface for directly connecting portable consumer electronics to high-definition displays.
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • The monitor does not support DisplayPort converter signal. • Front Power Switch and computer power switch should be in the ON position. • The monitor will automatically turn off by “POWER SAVE TIMER” function when continuing power save mode for 2 hours. Please touch the power key.
• Make certain the computer is not in a power-saving mode (touch the keyboard or mouse). • Some video cards do not output video signal when monitor is turned OFF/ON or disconnect/connect from the AC power cord under low resolution with DisplayPort. • When using an HDMI input, please change “OVER SCAN”. No Sound • Make sure the speaker cable is proper connected. • Check to see if mute is activated. • Check the VOLUME in the OSD menu.
Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions. The Auto Brightness function is set to 1 by default.
This monitor can display split screens from two sources by using any one of the input combinations shown on page 15. NOTE: Please see PBP MODE (page 15) and PBP TYPE (page 15).
Using the Zoom Function Allows you to use the entire screen area, significantly expanding the size. Allows the picture displayed in the center to expand. NOTE: When in PBP MODE, the sub picture is expanded or reduced automatically. SETUP 1. Select FULL or ASPECT in EXPANSION to activate the Zoom function (see page 14). EXPANSION OFF 2. Set a resolution via H.RESOLUTION or V.RESOLUTION (see page 14). Vertical expanding Horizontal expanding 3.
To enlarge the split images: use the following procedures to reduce the black area and enlarge the split images. 1. In case A, a priority image is set to be on the right side. The size of the black area can be reduced by adjusting the resolution (see page 14). 2. Move the priority image to the left side. English-25 English B. The left image is set to be the main one. In this case, the priority image is set to be on the left side. The size of the image on the right side with black area is reduced.
ControlSync 1. Connect the master monitor with a sub monitor via a ControlSync cable (ø 2.5) into ControlSync IN/OUT. 2. Follow the steps of DATA COPY. When the setting of the master monitor is adjusted, it will be copied and sent to the connected sub monitor(s) automatically. 3. Up to 5 sub monitors can be daisy-chained via ControlSync. NOTE: Connect the master monitor via ControlSync OUT connector. The ControlSync icon will appear on the upper left of the OSD menu in the sub monitor.
Congratulations! This product is TCO Certified – for Sustainable IT TCO CertiÞed is an international third party sustainability certiÞcation for IT products. TCO CertiÞed ensures that the manufacture, use and recycling of IT products reßect environmental, social and economic responsibility. Every TCO CertiÞed product model is veriÞed by an accredited independent test laboratory. TCO CertiÞed Edge is a supplemental certiÞcation recognizing best in class products in a speciÞc sustainability attribute.
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentallyfriendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).
