Windows Server™ 2003 with SP1 Installation Guide Version 1 855-900550-200 1
CONTENTS WINDOWS SERVER™ 2003 WITH SP1................................................................................................................ 1 INSTALLATION GUIDE ..................................................................................................................................... 1 SOFTWARE INSTALLATION AND CONFIGURATION NOTES ............................................................................... 3 Before setting.............................................................
Software Installation and Configuration Notes Before setting z Partition size Minimum size of the partition can be calculated from the following formula. 1635MB + paging file size + dump file size 1635MB = required for installation Paging file size (recommendation) = installed memory size x 1.5 Dump file size = installed memory size + 12MB 重要. Paging file size is required to collect debug information (memory dump).
BIOS Setting Before you install the Windows 2003 Server, confirm the BIOS setting. Regarding the System Interruption mode Confirm the BIOS setting of the system interruption mode corresponding to the OS type. Regarding the BIOS setting, refer to the Hardware Guide; "System Hardware -> Shrink total number of interrupt vectors". If the setting is not correct, set the correct setting as follows.
6. Input "fs0:」after Shell>, press Shell>fs0: Command prompt will change to fs0:＼ 7. Input 「setupldr」 after fs0:＼>, press fs0:＼>setupldr When a SCSI/RAID adapter needs a driver other than OS standard driver, Please use the driver diskette appended to the adapter, or the driver diskette which copied the driver files of EXPRESSBUILDER inclusion, and execute OS installation in the following procedures. For details, refer to the document appended to the adapter, or included on EXPRESSBUILDER.
(6) Press when the reading from the Driver FD device is finalized, continue setup. When following dialog is shown, press [OK] and continue 8. Continue set up following the message and complete installation. When following message is shown, press [Enter] and continue. "System partition can not be found" At the initial set up, Hard disk configuration is as follows. Please do not delete "Partition 1[FAT] " and "Partition 2[reserved]".
Installation and setup of the drivers This section describes installation and setup of the standard devices' drivers. After completion of the driver setup, go to "Setup for the trouble shooting" section. The device developed by NEC Installation of the driver for the device developed by NEC is executed from "Software Setup Menu" of NEC EXPRESSBUILDER. 1. Insert the NEC EXPRESSBUILDER CD-ROM in the CD-ROM drive. The NEC EXPRESSBUILDER Master Control Menu appears. 2. Select the “Setup”.
1. 2. 3. 4. 5. Click Start menu, Click [Settings] and Click [Network Connections]. The [Network Connections] dialog box appears. Right-click [Local Area Connection] and click [Properties] from pop-up menu. The [Local Area Connection Properties] dialog box appears. Click [Configure]. The property dialog box for network adapter appears. Select [Advanced] tab and set the [Link Speed & Duplex] value the same as the value specified for HUB. Click [OK] on the property dialog box for network adapter.
Setup for the trouble shooting In order to recover the system from the unexpected trouble, please finish the following setup in advance. When you finish the following setup, please go on with the section of "Installation of Management utility". Here is the procedure, provided it is indicated in the described way. - Select "taskbar's properties" and "Start Menu" tab, click "Classic Start menu". - Select "explorer's folder options", click "Show common tasks in folders".
Here is the procedure of Memory Dump Setup. 1. Click the "Control Panel" from the start menu. The "Control Panel" window appears. 2. Double click the "System" icon in the window of "Control Panel". The window of "System Property" appears. 3. Click the "Advanced" tag. 4. Click the "Setting " tag of the "Startup" box. 5. Enter the debug information into the text box for text input, and click "OK". For example, if you want to record your information into the file of MEMORY.DMP under D drive, input D:\MEMORY.
6. Click the "Setting" tag of the "Performance" box. The window of "Performance Option" appears. 7. Click the "Detailed Setup" tag of the "Performance Option" window. 8. Click the "Change" tag of the "Virtual Memory" box.
9. Change the "Initial Value" larger than the recommended value in the "Paging File Size of the Selected Drive", and Click the "Set" tag. Please set the "Initial Value" of the paging file to about 1.5 times of the equipped memory. z z z z Please be sure to create the paging file in the OS partition. Correct information might not be collected if the initial size is set smaller than the recommended value. Please set the paging file again according to the new memory capacity when memory is enhanced.
Dr. Watson “Dr Watson” is the debugger for Application error. When an application error is detected, it diagnoses the server and logs the diagnosis information. To extract the diagnosis information, set up as follows. Dr. Watson is set up when you buy the server or re-set up the server. 1. Click [Run.] in Start menu. 2. Input “drwtsn32.exe” in the name box. 3. Specify the location where the diagnosis massages will be saved in [Log File Path] (L). Network Path can not be specified.
Remote Desktop Following is the explanation for the validation of the remote desktop connection and the connection method from the client. The validation of remote desktop connection on the server Set as follows. 1. Select [Control Panel] in Start menu. Then Control Panel Window is displayed. 2. Double Click [System] in the window. 3. Click [Remote] tab. 4. Check [Allow users to connect remotely to this computer].
5. When the following message is displayed, Click [OK] and set the password of the user who executes the remote desktop connection.
Sharing Setup Folder of the remote client To execute the remote desktop connection from Windows95, Windows 98, Windows NT 4.0 or Windows 2000, the installation of Remote Desktop Client is needed. The client software is available from the following folder on the server. %SystemRoot%\System32\Clients\Tsclient\win32 In order to install the client easily to other computer, make a shared folder on the server with following procedure. 1. Move to the below folder by Window Explorer.
Client of Remote Desktop connection feature ”Remote Desktop connection feature” have been installed as default at Windows XP and all version of Windows Server 2003. The installation will be started by connecting above feature when you use Microsoft Windows 95, Microsoft Windows 98, Microsoft Windows Millennium Edition (Me), Microsoft Windows NT 4.0 and Microsoft Windows 2000. Connect to above feature. The share name is “\\Server‘s_name\TSC Client”.
3. Check the ［Accept the license Agreement］, and click the [Next] 4. Type the [User name] and [Organization] at ［User Information］ dialog box. And click [Next]. 5.
Click [Install] when the [completion of program installation] is displayed.
How to connect to Server from the Remote Desktop Client This is displayed. 1. Select [Program] -> [Accessories] -> [Communications] -> [Remote Desktop Connection] from startup menu. 2. [Remote Desktop Connection] is started. IP address or computer name should be typed. Recovery of System The Recovery console should be used for system repair when the system cannot to bootup by something.
Trouble shooting When the Windows Server 2003 does not work well, please check the following check list before you will ask maintainer to repair the PC. When the PC’s condition has been matched to items, obey to the confirmation and the transactions. But it does not work well, please call maintenance service after the display messages should be written down. A hard disk drive cannot be initialized. The Windows DiskManager of Windows Server 2003 have been stalled.
➞ Ｍｅｓｓａｇｅs ｏｆ ＯＳ ｅｖｅｎｔ ｌｏｇ Type Warning Warning Warning Source PNPMEM Event ID 0 User NA description Failed to add memory range starting at 0x7F000000 for 0x300000 bytes. This operation exceeded the maximum memory capacity of the operating system or the server is not configured to support dynamic memory operations. Failed to add memory range starting at 0x140000 for 0x30000 bytes.
NEC EXPRESSBUILDER The CD-ROM that comes with your server contains a setup utility called "NEC EXPRESSBUILDER." When you have first installed the server or append features to the server, use the NEC EXPRESSBUILDER to set up your server. The major functions of the NEC EXPRESSBUILDER are: To install the utilities. It installs the management utilities. To install device drivers. To read the online documents. It opens the online document files (".pdf" files or “.html” files).
(c)NEC Corporation 2003-2006 To use Master Control Menu, click [Online Document], [Setup] or [Quit]. These items are as follows: z Online Document You can refer to installation guides and online document on each utility. z Setup You can install utilities. For installation procedure and detailed explanations on each utility, please refer to the online document. z Quit Master Control is closed. IMPORTANT: 24 Do not remove the NEC EXPRESSBUILDER CD-ROM while NEC EXPRESSBUILDER is running.
Troubleshooting problems When the Windows Server 2003 does not work well, please check the following check list before you will ask maintainer to repair the PC. When the PC’s condition has been matched to items, obey to the confirmation and the transactions. But it does not work well, please call maintenance service after the display messages should be written down.
→ The Master Control menu is supported by Windows NT 4.0 or later and Windows 98 SE or later. The target OS of the EXPRESSBUILDER is Windows Server 2003 or Windows 2000/XP or later. (2)Is Shift pressed? → Setting the CD-ROM with Shift pressed down cancels the Autorun feature. (3) Did you install the HTML browser on your server? →Master Control Menu is “.html” file. Please install the HTML browser on Windows in advance. (4) Is “.html files or .
ESMPRO/ServerAgent (Windows) ESMPRO/ServerAgent(Windows) lets a system administrator manage remote servers across a network. ESMPRO/ServerAgent monitors server hardware and software configurations, failures, and performance. With log data collected by NEC ESMPRO, a system administrator can track long-term and short-term performance, monitor server usage, create graphs to record trends, and check server failure rates.
document. About the Memory Bank In DataViewer, [Module Information] on "Memory Bank" shows that the total size of memory mounted in CELL as one module. In case one CELL mounts 32GB or more memories, [Module Size] shows "0KB." and [Bank Size] shows the sum of each [Module size].
