MultiSync ® ® LCD400 LCD2000 ™ ™ User’s Manual Contents Quick Start Controls Recommended Use Specifications Features Troubleshooting References Limited Warranty 78132391 1 1 2-3 4-5 6-7 8-9 10 11 12 13 10/29/99, 8:42 AM
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
Contents Your new NEC Technologies MultiSync® LCD monitor box* should contain the following: • MultiSync LCD Monitor with tilt/swivel base MultiSync LCD400™ monitor, LA-1421JMW or MultiSync LCD2000™ monitor, LA-2031JMW • Power Cord • Video Signal Cable (LCD400) • 15-pin VGA to BNC Cable (LCD2000) • User’s Manual • Registration Card MultiS ync LC D ync LC MultiSync LCD400 monitor with Video Signal Cable MultiSync LCD2000 monitor with 15-pin VGA to BNC Cable Xtra View Mu l L tiS LC CD40 ync Us D 0 2 PR
Quick Start To attach the MultiSync® LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC: Connect the 15-pin mini D-SUB of the appropriate signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the Mac: Connect the MultiSync LCD400™ or MultiSync LCD2000™ Macintosh cable adapter to the computer (Figure B.1).
Quick Start Figure C.1 H/CS VS R G/Sync B Figure D.1 MultiSync LCD400 monitor MultiSync LCD2000 monitor Figure E.1 MultiSync LCD400 monitor MultiSync LCD2000 monitor 15-pin mini D-SUB Power Switch Power Switch Figure F.
Controls OSM™ (On-Screen-Manager) Controls The OSM controls on the front of the monitor function as follows: Control EXIT Main Menu Exits the OSM controls. Sub-Menu Exits to the OSM controls main menu. Moves the highlighted area up/down to select one of the controls. Moves the highlighted area up/down to select one of the controls. CONTROL –/+ Has no function. Moves the bar in the + or – direction to increase or decrease the adjustment.
Controls AccuColor™ Control System Color presets select the desired color setting. If a setting is adjusted, the name of the setting will change to Custom. Color Gain (Red, Green, Blue): Increases or decreases Red, Green or Blue color depending upon which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown by the color bars. OSM™ Location You can choose where you would like the OSM control image to appear on your screen.
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC® LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Allow adequate ventilation around the monitor so that heat can properly dissipate.
Recommended Use CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 16 inches and no further away than 28 inches from your eyes.
Specifications MultiSync® LCD400™ Monitor Monitor Specifications LCD Module Diagonal: Viewable Image Size: Native Resolution (Pixel Count): Input Signal Video: Sync: Display Colors Synchronization Range 14.1 inch 14.1 inch 1024 x 768 Active matrix; thin film transistor (TFT) liquid crystal display (LCD); 0.28 mm dot pitch, XtraView™ technology; 180cd/m2 white luminence; 100:1 contrast ratio, typical ANALOG 0.7 Vp-p/75 Ohms Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync.
MultiSync® LCD2000™ Monitor Monitor Specifications LCD Module Diagonal: Viewable Image Size: Native Resolution (Pixel Count): Input Signal Video: Sync: Display Colors Synchronization Range 20.1 inch 20.1 inch 1280 x 1024 Active matrix; thin film transistor (TFT) liquid crystal display (LCD); 0.31 mm dot pitch, XtraView™ technology; 150cd/m2 white luminence; 100:1 contrast ratio, typical ANALOG 0.7 Vp-p/75 Ohms Separate sync. TTL Level Horizontal sync. Positive/Negative Vertical sync.
Features Analog Advantage: Capable of displaying unlimited colors in a continuous spectrum, providing a truer representation of color. The monitor’s high contrast LCD enhances color vibrancy and improves focus with no geometric distortion. Wider Compatibility: Because the MultiSync LCD monitor is analog through and through, it does not require special analog to digital display or interface cards but can accept RGB input directly.
Troubleshooting No • • • • picture The signal cable should be completely connected to the display card/computer. The display card should be completely seated in its slot. Power Switch and computer power switch should be in the ON position. Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and your display card with respect to compatibility and recommended settings.
References • BBS (508) 635-4706 NEC Technologies’ Remote Bulletin Board System is an electronic service accessible with your system and a modem. Communication parameters are: 300/1200/2400/9600/14.4k/28.8k/33.3k bps, no parity, 8-data bits, 1 stop bit • Customer Service/ Technical Support Fax (800) 632-4662 (508) 635-4298 • Electronic Channels: Internet e-mail: tech-support@nectech.com Internet ftp site: ftp.nectech.com CompuServe: go NECTECH America Online: keyword NECTECH World Wide Web: http://www.
Limited Warranty NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace any part of the enclosed unit, other than the LCD backlight, which proves defective for a period of three (3) years from the date of first consumer purchase. The LCD backlight is warranted for a period of one (1) year. Spare parts are warranted for ninety (90) days.
NEC LCD Series PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Technologies and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use and sales rights thereto, except to the extent said rights are expressly granted to others.
