User’s Manual LED Module [Models for indoor use] LED-FC009i LED-FC012i LED-FC015i MODELS: LED-FC009i, LED-FC012i, LED-FC015i
Table of Contents Important Information ...................................................................English-1 Contents .........................................................................................English-5 Related Items for Installation ........................................................English-6 Parts Name and Functions ..............................................................English-7 Wiring ......................................................................................
Important Information Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LED DISPLAY SYSTEM: About the Symbols To ensure safe and proper use of the product, this manual uses a number of symbols to prevent injury to you and others as well as damage to property. The symbols and their meanings are described below. Be sure to understand them thoroughly before reading this manual.
● Be sure to read the following before using the product to use it correctly and safely. WARNING Do not apply vibrations or shocks to the product. Install the product so that the vents are not obstructed. Make sure there are enough people available to ensure safety (at least two people) when installing or moving the product. Otherwise, it may lead to an injury. Do not install the product to unstable locations or locations subject to vibrations. Always ask a technician to perform the installation.
CAUTION When connecting the power cord to the product’s AC IN terminal, make sure the connector is fully and firmly inserted. Do not damage the power cord. Do not put heavy objects on it, place it near heaters, pull it with excessive strength, or apply a strong force on it while it is bent. A damaged power cord may cause a fire or an electrical shock. Do not install the product in narrow places where heat tends to build up. Do not use or store the product in the following places.
Recommended Use & Maintenance About the LED lamps The surface of the pixel card is vulnerable to shocks, so do not press or hit the surface. LED lamps are sensitive to static electricity and surge voltage, which may damage their components and decrease their reliability. Take measures against static electricity during the installation. Do not touch the LED display areas. The LED lamps may absorb and hold moisture during the LED module installation or if not used for a long time.
Contents The supplied parts are as follows. In case one of these parts is missing or damaged, contact the retailer. CAUTION Depending on the system you ordered, there is a cabinet without the upper connector.
Related Items for Installation The items required when installing the system are shown below. Contact your retailer for more details. [Power cord] To connect the LED module to the power distributor [LAN cable] To connect two LED modules together (120 mm for vertical connection, 1000 mm for horizontal connection) [Cabinet alignment bracket] [Connection screw for LED modules] [USB drive] Contains the data, the user’s manual (this document), and the control software for the product you have purchased.
Parts Name and Functions ⑥ ② ④ ⑫ Front Rear ⑪ ① ③ ⑦ ⑩ ⑧ ⑤ ⑨ Name Interface connectors Description Input and output connectors for the signal and AC power. 12 Signal input/output To input the signal from the LED controller or the previous LED module. When a signal is input into 1, the signal is output from 2. When a signal is input into 2, the signal is output from 1. 34 Signal input/output Not functioning with this product.
There are two types of cabinets. Power hub board (1) Type A The connectors are equipped on the top and bottom sides. There are guide pins on the top. Receiving card Power unit Power hub board (2) Type B There are no connectors on the top side. There are no guide pins. Receiving card Power unit Power hub board [When assembling a 6 x 6 frame set using FC009i] It is necessary to connect a LAN cable in the middle of the installation work.
Wiring (1) Maximum number of signal connections The maximum number of connections per LAN cable is shown below. Product name Maximum number of connections LED-FC009i 2 modules LED-FC012i 5 modules LED-FC015i 7 modules CAUTION The maximum number of connections may differ depending on the connected LED controller. Therefore, check the specifications of the LED controller you are using. Ask a technician or your retailer for more details.
Specifications LED-FC009i LED configuration LED-FC012i LED-FC015i Flip chip COB (chip size : 4mil*8mil) Pixel pitch Number of displayed pixels (resolution/module) 0.95 mm 1.26 mm 1.58 mm 640 × 340 480 × 270 384 × 216 800 cd/m2 Brightness Contrast ratio 20000:1 Brightness adjustment range 0 to 100% (256 increments) Gamma correction 1.0 to 4.0 (default setting: 2.
Diagram LED-FC009i / LED-FC012i / LED-FC015i 48.5 342 608 Rear 4 x M8 18.
WEEE Mark (European Directive 2012/19/EU and amendments) Disposing of your used product: In the European Union EU-wide legislation as implemented in each Member State requires that used electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes LED Poster and electrical accessories, such as signal cables or power cords.
