MD302C6
Disclaimer * Windows and MS-DOS are trademarks and/or registered trademarks of Microsoft Corporation in the United States and/or other countries. * VESA is a trademark of the Video Electronics Standard Association. * All other products and company names are trademarks of their respective owners.
English
Index Registration Information ...............................................................................................................English-2 Intended Use ................................................................................................................................English-4 Recommended use ......................................................................................................................English-5 Contents ........................................................
This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. CAUTION This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. Protective earth terminal marked. Stand by. AC Input. Main Power On. Main Power Off.
Registration Information Declaration Declaration of the Authorized Representative NEC Display Solutions Europe GmbH declares that the product listed is in conformity with the essential requirements and provisions of the Council Directive 93/42/EEC, including the amendments of the Council Directive 2007/47/EC, and conforms to the applicable clauses of the following standards: Means of Conformity Device Classification: Class I, non-measuring function Applicable Rules: Annex IX, Rules 1.
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION THIS APPARATUS MUST BE EARTHED BECAUSE OF CLASS I EQUIPMENT. TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
Intended Use The MD302C6 color monitor is intended to be used for displaying and viewing of digital images by trained physicians. Caution: The MD302C6 color display cannot be used for a life-support system. This device is designed as component of a final system which is in compliance to IEC 60601-1-1 requirements. Contraindications: None known. Safety Precautions This device is designed for exclusive interconnection with IEC 60950-1 certified equipment outside of patient vicinity.
Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONITOR: WARNING: Do not modify this equipment without authorization of the manufacturer. WARNING: To disconnect this product from the mains supply disconnect the mains plug from the socket outlet. WARNING: To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth. WARNING: No modification of this equipment is allowed.
Image Persistence: Image persistence exists, when a residual or “ghost” image of a previous image remains visible on the screen. Unlike with CRT monitors, image persistence on LCD monitors is not permanent, but constant images being displayed for a long period of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed.
English Contents Your new NEC monitor box* should contain the following: • MD302C6 monitor with tilt/swivel/height adjust stand • Power Cord • Video Signal Cable (DVI-D to DVI-D cable)*1 x 2 • Video Signal Cable (DisplayPort to DisplayPort cable) x 2 • USB Cable • Quick Reference Guide Power Cord*2 DisplayPort cable x 2 Quick R eferenc e Guide Quick Reference Guide USB Cable DVI-D to DVI-D cable*1 x 2 * Remember to save your original box and packing material to transport or ship the mon
Connecting the cables To connect the LCD monitor to your system, please follow these instructions: NOTE: Make sure to read “Recommended Use” before installation. In order to display the maximum resolution, a display controller that can output a resolution of 3280 x 2048 is needed. 1. Turn off the computer. 2. DVI connection: Connect the supplied digital signal cables between the display’s DVI and the computer’s DVI connector.
English Caution For connection to the DVI input(s), make sure to use a DVI Dual Link cable. Dual-link • Single-link Precautions to display two 3MP screens from one computer (Figure D): A display controller model, which has two outputs of the same signal type (either DVI + DVI or DisplayPort + DisplayPort) is recommended. Using two outputs with different signal types, (i.e. DVI + DisplayPort) of the same display controller is not recommended.
When using a USB hub... This display has a USB 2.0 compliant hub. By connecting the supplied USB cable to a USB 2.0 port of the computer or another USB 2.0 hub, USB devices can be connected to the display directly. With the computer and the display turned on, connect the supplied USB cable between the display’s USB upstream port and the computer’s USB 2.0 downstream port.
English Controls Power On/Off Press and hold the switch to turn on/off the display. NOTE: Wait at least 10 seconds between on/off actions. MINUS button Without displaying the OSD on the screen, press this button to switch the input source of INPUT 1 to DisplayPort 1 or DVI 1. (This function is available only when “ENABLE FUNCTIONS” setting of the direct OSD menu setting is set to “Enable Switching Input Source” or “Enable Both Functions” (see page 26)).
DisplayPort 1 DVI DOWN UP DVI 2 POWER DisplayPort AC IN AC Inlet: Connect the supplied Power cord. Main power switch: Main power supply switch. INPUT1 of DisplayPort-1: Digital video signal input port. Connect the supplied DisplayPort cable. INPUT1 of DVI-1: Digital video signal input port. Connect the supplied DVI cable. INPUT2 of DisplayPort-2: Digital video signal input port. Connect the supplied DisplayPort cable. INPUT2 of DVI-2: Digital video signal input port.
Two methods to switch signal inputs are available, input port switching and input source switching. Press the appropriate buttons located on the front bezel of the display as follows. Input port switching “Input port” here means a combination of the input sources of DisplayPort and DVI. There are two input ports, INPUT 1 and INPUT 2. See the following table and figure for the difference between input port and input source.
The following shows an example of the case when the resolution of QXGA (1536 x 2048) is selected for both INPUT1 and INPUT 2. By pressing the MENU button and switching a port, both screens are active when INPUT 1 + INPUT 2 is selected. INPUT 1 INPUT 2 INPUT 1 + INPUT 2 The following shows an example of the case when the resolution of 3072 x 2048 is selected for INPUT 1 and QXGA (1536 x 2048) is selected for INPUT 2.
The following shows an example of the case when Displayport is selected for the input source of both INPUT 1 and Input 2, and the input source of INPUT 2 is switched to DVI. NOTE: Using INPUT 1 and INPUT 2 with different input sources (DVI + DisplayPort) is not recommended for standard applications. It may result in slight differences of luminance and color between left and right screen and/or a frame skip (See page 9).
Display information Press the appropriate button located on the front bezel of the display to see display information or change settings. 1. Displaying the OSD menu Press and hold the MENU button for 2 seconds. The following OSD menu appears. MENU I N F ORMA T I ON PRE S ENT STATE D I C OM C O N F O R M A N C E ME NU S E L E C T I ON EX IT OSD menu TEST See the following pages for all display information items.
The OSD full menu structure and a brief explanation for each menu item is listed as follows. The highlighted items are shown in the Reference Menu. The other items are only shown in the Full Menu. • INFORMATION ........................................................................ Shows display information • PRESENT STATE .................................................................... Shows luminance and gamma correction information • DICOM CONFORMANCE TEST ...........................................
Displaying information Various display information can be checked by selecting from the OSD menu. 1. Displaying the OSD main menu Press and hold the MENU button for 2 seconds. The OSD menu appears. Press either + or - button to move the cursor “ ” and select “INFORMATION”. Reference Menu Full Menu 2. Information window Press the MENU button and the information submenu appears.
NOTE: This function is available only when the display has been calibrated to DICOM GSDF. Performing a DICOM conformance test ensures DICOM conformance of the display by measuring and checking the display properties. The DICOM conformance test is recommended to be performed after 60 minutes of continuous active backlight time of the LCD panel.
4. Performing the DICOM conformance test Press either + or - button to select “Yes” for START TESTING. (DICOM conformance test starts immediately). Screen that shows the test is in execution It takes between 30 seconds to 1 minute to complete the test. To cancel the test, press either + or - button to select “Yes” for CANCEL TESTING. 5. Showing the test results When the test has completed, the results are shown similar as below.
Different menu contents can be shown for the menu screen by switching between “Reference Menu” and “Full Menu”. Full Menu allows setting changes. Select “MENU SELECTION” for switching menu contents. 1. Displaying the OSD main menu Press and hold the MENU button for 2 seconds. The OSD main menu appears. Press either + or - button to move the cursor “ ” and select “MENU SELECTION”. Reference Menu Full Menu 2. Switching the OSD menu Press the MENU button. The MENU SELECTION window appears.
2. Switching EDID sub menu Press the menu button and the SWITCHING EDID submenu appears. Press either + or - button to move the cursor “ ” and select the preferred mode. See below for selectable resolutions. Press the MENU button again to store the preferred EDID. Switching EDID NOTE: The OSD menu disappears in 15 seconds. EDID 6MP+ (3MP+x2) Explanation “Full pixel mode”, using the complete area of the LCD panel: The display is used with a resolution of either 3280 x 2048 or 2x 1640 x 2048.
The model MD302C6 can save up to three different Luminance - Gamma - Color Tint configuration settings within the display. These settings are selectable by a configuration number, which is shown in the PRESENT STATE submenu. The following three configuration settings were saved prior to shipping, with configuration 1 as the default setting. Configuration number 1 2 3 Luminance (cd/m2) Maximum Minimum Ambient 400 0.8 0.0 400 0.8 0.0 300 0.8 0.
3. Confirming the configuration change Press the MENU button and return to the full main menu, same as in step 1. Press either + or - button to move the cursor “ ” and select “PRESENT STATE”. Full Menu Press the MENU button and the PRESENT STATE submenu with the selected configuration number appears. The following picture shows the case when configuration 2 was selected. PRESENT STATE Configuration number NOTE: The OSD menu disappears in 15 seconds.
The direct OSD setting menu allows function setting to be enabled or the mode setting to switch an input signal. Follow the instructions below. By default, this function is disabled. Functions to be enabled 1. Displaying the OSD main menu Press and hold the MENU button for 2 seconds. The OSD main menu appears. Press either + or - button to move the cursor “ ” and select “DIRECT OSD SETTING MENU”. Direct OSD Setting Menu 2.
Enable Functions Explanation Disables both input signal switching and input port switching. (When you try disabled switching operation, the menu will show “LOCKED”). Disable Enables input source switching only. (When you try input port switching, the menu will show “LOCKED”). Enables input port switching only. (When you try input source switching, the menu will show “LOCKED”). Enables both input signal switching and input port switching.
Press the MENU button and the INPUT SOURCE BUTTON MODE submenu appears. INPUT SOURCE BUTTON MODE Press either + or - button to move the cursor “ ” and select either mode. INPUT SOURCE BUTTON MODE Separate Mode* Concurrent Mode Explanation To change the input signal of INPUT 1 and INPUT 2 separately by pressing the + or the - button. To change the input signal of INPUT 1 and INPUT 2 simultaneously by pressing the + or the - button. * “Separate Mode” is the factory default.
Specifications Monitor Specifications MD302C6 LCD panel color Clear Base Notes LCD 30.0-inch (76.8 cm), color, TFT, Active matrix type, normally black Anti-glare Pixel pitch (H x V) 0.197 x 0.197 mm Display area (H x V) 645.5 x 403.05 mm Pixel (H x V) 3280 x 2048 Display colors 8 bit:16.77 million out of 68 billion* 10 bit: 1.07 billion out of 68 billion* Backlight LED backlight LCD Optical characteristics (typ.
The tilt and swivel stand, as shipped with the display, is interchangeable with commercially available wall mounts or multi-display mounting arms that: • Come with a mounting plate with 6 slotted screw holes at 100 mm x 200 mm, and • Bear the total weight of the LCD panel (without the stand) and the cables connected to it. For more information ask your mounting arm supplier. Note: Use the original screws to use the LCD panel back on its original tilt stand.
Antitheft Security Slot The display is equipped with the security slot for use with the MicroSaver Security Lock System by Kensington Technology Group. The MicroSaver locks are available at PC supply stores. DOWN UP DVI 2 POWER DisplayPort AC IN DVI 1 DisplayPort Note: Kensington is the registered trademark of Kensington Technology Group.
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentallyfriendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization).
NEC Display Solutions, Ltd. 4-28, Mita 1-chome, Minato-ku, Tokyo, Japan NEC Display Solutions of America 500 Park Blvd. Suite 1100 Itasca, Illinois 60143 USA Phone: +1-630.467.3000 Fax: +1-630.467.3010 NEC Display Solutions Europe GmbH Landshuter Allee 12-14 D-80637 Muenchen Germany Phone: +49(0)89/99699-0 Fax: +49(0)89/99699-500 Vol.
