NEC Professional Series User’s Manual
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
Contents 2 Packaging 3-5 Quick Start Introduction Screen Technology CROMACLEAR™ CRT Dynamic Beam Focus OptiClear® Screen Surface Plug and Play ErgoDesign® Features Power Manager Reduced Emissions Multiple Frequency Technology MultiCable™ Connection System OSM™ (On-Screen Manager) Controls Controls Control Panel OSM Elements OSM Controls Menu Main Menu 6-8 6 6 6 7 7 7 7 7 7-8 8 8 9-12 9 9 9 10 Brightness/Contrast Controls Size and Position Controls Color Control/AccuColor® Control System Geometry Contro
Packaging 2 Contents of Package Congratulations on your purchase of the MultiSync® P750™ Is the color monitor! computer a Macintosh The following listsII all of the items included with your MultiSync or LC monitor package: computer? 1. MultiSync P750 (JC-1744UMA) monitor with tilt/swivel base 2. Power cord 3. MultiCable™ connection system 4. User’s manual 5. Registration card: Please fill out and return this card as soon as possible.
Quick Start No Is the monitor a MultiSync® P750™ monitor? Attach the MultiCable™ connection system or BNC cable to the display card first and then to the monitor. Yes Is the BNC Input being used? Yes Set the BNC/DSUB switch to the out position. 3 No If necessary, use the OSM™ controls to adjust the image to personal preference. Is the image correct? Set the BNC/DSUB switch to the in position. Connect one end of the power cable to the MultiSync monitor and the other end to a power outlet.
4 Quick Start Connection To Your Personal Computer For the PC: Your system has one of two configurations: – the video controller is built into the computer – the video controller is in the form of a display card (sometimes referred to as the graphics card, video adapter or graphics board) Both configurations have a video connector (or a CRT PORT on laptop computers). If you are not sure which port is the video connector, please consult your computer or display card manual.
4. Make sure the BNC/D-SUB Switch on the front of the monitor is set to the D-SUB (in) position. For the PC: Connect the 15-pin mini D-SUB (the smaller connector) end of the MultiCable™ connection system to the connector of the display card in your system. Connect the 15-pin D-SUB (the larger connector) end of the MultiCable connection system to the monitor. For the Mac: Connect the 15-pin D-SUB (the larger connector) end of the MultiCable connection system to the connector of the display card.
6 Introduction Congratulations on your purchase of NEC’s MultiSync® P750™ color monitor! The MultiSync P750 monitor delivers superior image quality for all your demanding application needs. The MultiSync P750 monitor delivers the power you need for today’s high-end applications. The MultiSync P750 monitor features the latest advancements in display technology, allowing you to take advantage of all your sophisticated applications.
Plug and Play Plug and Play is the new Microsoft® solution with Windows®95 to provide automatic peripheral connections without confusing and time-consuming setup. When used with a Plug and Play system and display card, the MultiSync® P750™ monitor automatically tells the system its identification and capabilities. The system will then select its highest resolution and refresh rate to take advantage of your MultiSync monitor.
8 Introduction Increased refresh rates at all resolutions provide a flicker-free image which is easier on your eyes and extends your viewing time.
Controls OSM Elements Control Panel EXIT PROCEED RESET BNC/D-SUB CONTROL OSM control buttons on the front of the monitor function as follows: ™ EXIT CONTROL / CONTROL +/– PROCEED RESET NOTE: 9 Main Menu Exits the OSM controls. Moves the highlighted area up/down to select one of the controls. Moves highlighted area left/right to select one of the controls. Has no function. Resets all the controls within the highlighted menu to the factory setting. Sub-Menu Exits to the OSM controls main menu.
10 Controls Main Menu The icons control the following: Brightness/Contrast Controls Brightness: Adjusts the overall image and background screen brightness. Contrast: Adjusts the image brightness in relation to the background. Degauss: Eliminates the buildup of stray magnetic fields which alter the correct scan of the electron beams and affect the purity of the screen colors, focus and convergence. When activated, your screen image will jump and waver a bit as the screen is demagnetized.
decrease the adjustment or selects the color setting (1 through 5). Reset: Resets the current color setting to the factory setting. NEC’s AccuColor® control system allows you to change your onscreen colors by adjusting the monitor’s red, green and blue color guns individually. You can also access five industry standard color temperature settings. Geometry Controls Geometry Controls Menu The Geometry controls allow you to adjust the curvature or angle of the sides of your display.
12 Controls in the lock out mode, a screen will appear indicating that OSM™ controls are locked out. To activate the OSM Lock Out function, press PROCEED, then and hold down simultaneously. To deactivate the OSM Lock Out, press PROCEED, then and hold down simultaneously. IPM™ System Off Mode: Enable: The IPM System works normally and all stages of energy savings are utilized. Disable: The Off Mode of the IPM System is not used.
Specifications Monitor Specifications Picture Tube Diagonal: Viewable Image Size: Radius: Input Signal Video: Sync: Display Colors Synchronization Range Resolutions Supported Resolution based on horizontal and vertical frequencies only Analog input: Horizontal: Vertical: MultiSync® P750™ Monitor Notes 17.0 inch 15.6 inch 1210 mm 90° deflection, 0.
14 Specifications Monitor Specifications MultiSync® P750™ Monitor Notes Active Display Area (Factory Setting) 306 x 230 mm 12.0 x 9.1 inches Dependent upon signal timing used, and does not include border area. Active Display Area (Full Scan) 316 x 237 mm 12.4 x 9.3 inches Dependent upon signal timing used, and does not include border area. Power Supply Current Rating Dimensions AC 100 – 120 V, 50/60 Hz Weight 20.0 kg 44.1 lbs Environmental Considerations 1.
Recommended Use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC® P750™ COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts • • • • • inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. Allow adequate ventilation around the monitor so that heat can properly dissipate.
16 Recommended Use CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 12 inches and no further away than 28 inches from your eyes. The optimal distance is 18 inches.
Troubleshooting/Support Troubleshooting Chart Problem Check These Items No picture • • • • Image is scrolling or unstable • Signal cable should be completely attached to the computer. • Check the pin assignments and signal timings of the monitor and your display card with respect to recommended timings and pin assignments. LED on the monitor is not lit (no green, orange or yellow color can be seen) • Power Switch should be in the ON position and the power cord should be connected.
18 Troubleshooting/Support Problem Check These Items Picture bounces or a waving pattern is present in the picture • Move electrical devices that may be causing electrical interference away from the monitor. • See inside cover of this manual for FCC information. Edges of the display image are not square • Use the OSM™ Geometry Controls to straighten the edges. • If possible, position the monitor to face east.
FastFacts™ Information FastFacts information is an easy-to-use, automated facsimile service that provides you with information whenever you need it, 24 hours a day, seven days a week. You can call FastFacts information with your touchtone telephone, order a catalog listing the available documents or order the document you need. Within minutes, your requested information will be sent to your fax machine.
20 Warranty Limited Warranty NEC Technologies, Inc. (hereinafter NECTECH) warrants this Product to be free from defects in material and workmanship and agrees to repair or replace any part of the enclosed unit which proves defective under these terms and conditions. How Long is the Warranty Parts and labor are warranted for three (3) years from the date of the first consumer purchase. Spare parts are warranted for ninety (90) days.
2. Costs of initial technical adjustments (setup), including adjustment of user controls. 3. Payment of shipping and related charges incurred in returning the Product for warranty repair. How You Can Get Warranty Service You have the option of returning this Product to a NECTECH authorized service center or directly to a NECTECH factory for repair.
22 References AccuColor® Control System 10, 11 ™ 8 Advanced Digital Control System ANSI/HFS 16 BBS 19 (Remote Bulletin Board System) BNC 3. 4.
More Information Directory of Telephone Numbers More reference information regarding your MultiSync® monitor is available on NEC’s automated facsimile service, FastFacts™ information, by dialing (800) 366-0476.
PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use and sales rights thereto, except to the extent said rights are expressly granted to others.
Notes
NEC Professional Series Printed on Recycled Paper MultiSync is a registered trademark of NEC Technologies, Inc. NEC Technologies, Inc. 1250 North Arlington Heights Road Itasca, IL 60143-1248 Part No. 78131312 Printed in U.S.A.
