NDA-24273 ISSUE 1 STOCK # 152009 ® ISDN Features and Specifications APRIL, 2000 NEC America, Inc.
LIABILITY DISCLAIMER NEC America, Inc. reserves the right to change the specifications, functions, or features, at any time, without notice. NEC America, Inc. has prepared this document for use by its employees and customers. The information contained herein is the property of NEC America, Inc. and shall not be reproduced without prior written approval from NEC America, Inc. NEAX and Dterm are registered trademarks of NEC Corporation. Copyright 2000 NEC America, Inc. Printed in U.S.A.
ISSUE No. ISSUE No. PAGE No. PAGE No.
NEAX2000 IVS2 ISDN Features and Specifications TABLE OF CONTENTS Page BUSINESS FEATURE LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii SUPPORTED NETWORK SERVICES (TRUNK PRE-PROVISIONED ONLY) . . . . . . . . . . . . . . . . . . . . iii ISDN NETWORK REQUIREMENTS FOR LAYER ONE (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv TABLE OF FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BUSINESS FEATURE LIST Account code Answer Key Attendant Delay Announcement Attendant Overflow Authorization Code Automated Attendant Broker’s Call Call Forwarding Call Forwarding - All Calls Call Forwarding - Busy Line Call Forwarding - No Answer Call Forwarding - Outside Multiple Call Forwarding - All Multiple Call Forwarding - Busy Multiple Call Forwarding - No Answer Split Call Forwarding - Busy Line Call Forwarding - Override Group Division Call Park - System Call Pickup - Direct Call Pickup - Group Cla
SUPPORTED NETWORK SERVICES (TRUNK PRE-PROVISIONED ONLY) AT&T • Software Defined Network • Global Software Defined Network • International 800 Service • International MEGACOM® Also, AT&T’s Alternate Destination Call Redirection fearure is supported by the NEAX2000 IVS2. NT • Incoming -Private -Tie -WATS -800WATS Note • Outgoing -DID/DOD Note Note: Services that do not require NSF can be supported by the NEAX2000 IVS2. NEAX2000 IVS 2 ISDN Features and Specifications NDA-24273, Issue 1.
ISDN NETWORK REQUIREMENTS FOR LAYER ONE (1) • Interface: T1(1.544 M) only • Framing: ESF (24 Multiframe) only • Line Coding: B8ZS only • D Channel Rate: 64K only • D Channel: T1 Channel Number 24 (24th channel). Individual B channels cannot be looped back, local or remote. Page iv NEAX2000 IVS2 ISDN Features and Specifications NDA-24273, Issue 1.
TABLE OF FEATURES X = available FEATURE → = carried over to next level software 1900 2000 CALL-BY-CALL SERVICE SELECTION X → CALLED PARTY RECOGNITION SERVICE (DIRECT-IN TERMINATION (DIT)) X → CPN TO NETWORK—PRESENT X → CPN TO TERMINATING USER—DISPLAY X → DID ADDRESSING X → DID AND DOD ADDRESSING X → EVENT BASED CCIS X → ISDN TERMINAL X → MEGACOM ® ACCESS/WATS X → MEGACOM ® 800 SERVICE/800 WATS/ULTRA WATS X → MULTIQUEST®/900 SERVICE X → SUB-ADDRESS—PRESENT X → TRUNK P
This page is for your notes. Page vi NEAX2000 IVS2 ISDN Features and Specifications NDA-24273, Issue 1.
CALL-BY-CALL SERVICE SELECTION CALL-BY-CALL SERVICE SELECTION General Description Services can be selected on a call-by-call basis to all channels of a single PRI interface according to applications. That is, unlike Trunk Provisioning Service in which services are assigned to specific channels, services may be used on any available channel. Operating Procedure No manual operation is required. Service Conditions 1.
CALLED PARTY RECOGNITION SERVICE (DIRECT-IN TERMINATION (DIT)) CALLED PARTY RECOGNITION SERVICE (DIRECT-IN TERMINATION (DIT)) General Description This feature provides an incoming Direct-In Termination (DIT) call via an ISDN trunk to be connected to a predetermined station. This application can be used for a station or modem. Operating Procedure No manual operation is required. Station Application All stations. Service Conditions 1.
CPN TO NETWORK–PRESENT CPN TO NETWORK–PRESENT General Description This feature allows the ISDN network to be informed of the Calling Party Number (CPN) when a call originates from a terminal connected to the System. DIAL "516-555-4210#" For this example, the CPN sent to the network may be 214-555-5000 for every station in the PBX, or each station may present a unique extension number (last four digits) to the ISDN network. PBX DTI (214-555-5000) ISDN 4210 Called Party No.
CPN TO TERMINATING USER–DISPLAY CPN TO TERMINATING USER–DISPLAY General Description This feature provides a visual display of the originating station’s number and subaddress information on a Multiline Terminal for incoming ISDN calls. This provides the terminal user with a quick and accurate way to identify the originating station’s number (Calling Number). Operating Procedure No manual operation is required. The originating station number is automatically displayed on the Multiline Terminal.
DID ADDRESSING DID ADDRESSING General Description This feature allows incoming ISDN-PRI calls to terminate to stations, ATTCON, Automated Attendant, etc., based on the Called Party number. Direct Inward Dial trunks will be terminated to preprogrammed destinations without Attendant assistance. Operating Procedure No manual operation is required. Station Application Not applicable. Service Conditions 1.
DID AND DOD ADDRESSING DID AND DOD ADDRESSING General Description This feature allows the system to use DID and DOD on the same B channels. Trunk Provisioning Service Selection is not required. (B-channels can be used for DID and DOD without separating the trunk routes.) B-channels PRI D-channel Operating Procedure No manual operation is required. Service Conditions 1. Confirm the DID and DOD selection with the customer’s local exchange carrier prior to installation. 2.
EVENT BASED CCIS EVENT BASED CCIS General Description This feature allows a PBX customer that does not have a tie line (or when a customer can not use the tie line due to the busy or fault of the line), to use the various CCIS feature by using the ISDN line as a CCIS virtual tie line, on the 2400 IMX - NEAX2000 IVS2 connection or the NEAX2000 IVS2 - NEAX2000 IVS2 connection. Operating Procedure No manual operation is required. Service Conditions 1.
EVENT BASED CCIS Table 1 CCIS Features Available with Event Based CCIS SERVICE FEATURE AVAILABILITY Attendant Camp-On with Tone Indication-CCIS X Attendant Controlled Conference-CCIS X Brokerage-Hot-Line-CCIS X Busy Verification-CCIS X Call Back-CCIS X Call Forwarding-All Calls-CCIS X Call Forwarding-Busy Line-CCIS X Call Forwarding-Don’t Answer-CCIS X Call Forwarding-Intercept-CCIS X Call Forwarding-Override-CCIS X Calling Name Display-CCIS X Calling Number Display-CCIS X Call Tr
EVENT BASED CCIS Table 1 CCIS Features Available with Event Based CCIS SERVICE FEATURE AVAILABILITY Message Waiting Lamp Setting-Station-CCIS X Miscellaneous Trunk Access-CCIS X Miscellaneous Trunk Restriction-CCIS X Multiple Call Forwarding-All Calls-CCIS X Multiple Call Forwarding-Busy Line-CCIS X Multiple Call Forwarding-Don’t Answer-CCIS X Night Connection Fixed-CCIS X Night Connection Flexible-CCIS X Outgoing Trunk Queuing-CCIS – Paging Access-CCIS X Restriction from Outgoing Cal
ISDN TERMINAL ISDN TERMINAL General Description This feature provides the system with an ISDN Terminal or Terminal Adapter (TA). ISDN Terminal to ISDN Terminal, ISDN Terminal to ISDN Trunk, ISDN Trunk to ISDN Terminal, ISDN Terminal to Single Line Telephone, ISDN Terminal to Multiline Terminal, and ISDN Terminal to PS connections are available. Operating Procedure No manual operation is required. Service Conditions 1. The ISDN Line Circuit (ILC) card and the ISDN Channel handler (ICH) card are required.
ISDN TERMINAL 6. During communication via the CCIS network, the link reconnection is not available. 7. The conditions about station services are as follows: • Station Hunting When a Single Line Telephone/Multiline Terminal or an ISDN Terminal calls a busy Single Line Telephone/Multiline Terminal, another Single Line Telephone/Multiline Terminal in Station Hunting group is called.
ISDN TERMINAL 12. In case of Point to Multipoint connection, a Single Line Telephone/Multiline Terminal must dial ISDN Multipoint station number assigned by CM1B, not the ISDN Terminal number assigned by CM10. 13. When a Multiline Terminal calls an ISDN Terminal or an ISDN Terminal calls a Multiline Terminal, a calling station number is displayed to the calling Multiline Terminal or the ISDN Terminal.
MEGACOM® ACCESS/WATS MEGACOM® ACCESS/WATS General Description AT&T’s MEGACOM® (WATS) network, as well as WATS from other carriers, can be used. MEGACOM/WATS PRI ISDN NETWORK NEAX2000 IVS 2 Operating Procedure No manual operation is required. Service Conditions 1. The available WATS service is limited to Maximal Subscribed WATS Band (MSB). 2. No specific band will be indicated to the Network. NEAX2000 IVS 2 ISDN Features and Specifications NDA-24273, Issue 1.
MEGACOM® 800 SERVICE/800 WATS ULTRA WATS MEGACOM® 800 SERVICE/800 WATS ULTRA WATS General Description AT&T’s MEGACOM® 800 (Inward WATS) network, as well as 800 WATS provided by other carriers, can be used. MEGACOM/ 800 WATS ULTRA WATS PRI NEAX2000 IVS2 ISDN NETWORK MEGACOM 800 800 WATS ULTRA WATS Operating Procedure No manual operation is required. Service Conditions 1. CM76 can be used to convert indialed digits. 2.
MULTIQUEST®/900 SERVICE MULTIQUEST®/900 SERVICE General Description AT&T’s MultiQuest® service can be used. (It is a “900”-type service.) Also, 900 service provided by other carriers can be used. MultiGuest/ 900 Service PRI ISDN NETWORK NEAX2000 IVS2 Operating Procedure No manual operation is required. Service Conditions 1. The Dialed Number Identification Service (DNIS) must match the numbering plan (CM20) of the NEAX2000 IVS2. 2. Multiple DNIS numbers are supported. 3.
SUBADDRESS–PRESENT SUBADDRESS–PRESENT General Description This feature allows a primary rate interface ISDN trunk to transfer the called party subaddress information to a destination ISDN station when the call is originated by the NEAX2000 IVS2. Dialing the called party station number and subaddress is required.
TRUNK PROVISIONING SERVICE SELECTION TRUNK PROVISIONING SERVICE SELECTION General Description Each channel of a PRI interface can be dedicated to a particular service. Services are designated to specific channels; once designated, a channel can be used only for that service. Service A B-channels PRI Service B D-channel Operating Procedure No manual operation is required. Service Conditions • • The services that can be designated include MEGACOM®/WATS and MEGACOM® 800/800WATS.
This page is for your notes. Page 18 NEAX2000 IVS2 ISDN Features and Specifications NDA-24273, Issue 1.
APPENDIX A: Dterm FIXED FUNCTION KEYS APPENDIX A: Dterm FIXED FUNCTION KEYS Series E Series III Description Answer ANS To answer a waiting call Conf CNF To establish three-way conversation Feature FNC To activate terminal setup functions and to program One-Touch Speed Dial/Feature Keys Hold HOLD To place an internal or external call on hold Recall LNR/SPD To terminate established call and re-seize internal dial tone Redial RECALL To active Last Number Call and Speed Calling Speaker SP
APPENDIX B: Dterm LCD DISPLAYS APPENDIX B: Dterm LCD DISPLAYS Description Series E Series III Clock/Calendar Display 10:06 PM Busy BUSY XXXX BUSY XXXX Restriction RESTRICT XXXX RST XXXX Do Not Disturb DND XXXX DND XXXX Call Forwarding - All Calls CF ALL XXXX FDA XXXX Call Forwarding - Busy Line CF BUSY XXXX FDB XXXX Call Forwarding - No Answer CF NANS XXXX FDN XXXX Call Transfer TRANSFER XXXX XFR XXXX Conference CONF XXXX CNF Non Exclusive Hold HOLD XXXX HLD