User's Manual 23" TFT LCD TV NLT-23W / NLT-23WQ 23inch
Warnings WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : To reduce the risk of electric shock do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Warnings Service Never remove the back cover of the TV, this can expose you to high voltage and other hazards. If the TV does not operate properly, unplug it and call your nearest NEC service centre. Connect the antenna cable to the connection marked Ant. (on the rear). For best reception, use an outdoor antenna. Location Position your TV so that no bright light or sunlight will shine directly on the screen. Do not expose the TV to vibration, moisture, dust or heat.
Contents Before operating the set, please read this manual carefully. Warnings Contents Supplied Accessories Controls Controller of panel Remote controller Basic Operation Turning the TV On and Off Programme selection Volume adjustment Q.
Supplied Accessories L Make Sure the following accessories are provided with Product. 2. Remote controller 4. Owner’s manual User's Manual 1. AC Cord 23" TFT LCD TV NLT-23WQ 23inch 5. PC IN cable 3. Batteries (type AAA) 6 6.
Controls 1. ON/OFF Switches TV set on or off. 2. MENU Displays a menu. 3. ▼PR▲ (Programme Down/up) Selects a programme or a menu item. 4. ◀ VOL▶ (Volume Down/up) Adjusts the volume./ Adjusts menu settings. 5. TV/AV Selects TV, VIDEO1, VIDEO2, S-VIDEO, PC Analog, PC Digital, COMPONENT1 or COMPONENT2 mode./ Clears the menu from the screen. 6. Power Indicator Illuminates in red when the TV is in standby mode./ Illuminates in green when the TV is switched on.
Controls All the functions can be controlled with the remote controller. Some functions can also be adjusted with the buttons on the side panel of the set. Remote controller Before you use the remote controller, please install the batteries. 1. POWER Turns the TV on from standby or off to standby mode. 2. MUTE Turns the sound on and off. 3. NUMBER buttons Selects programme numbers. 4. TV/AV Selects TV, VIDEO1, VIDEO2, S-VIDEO, PC Analog, PC Digital, COMPONENT1 or COMPONENT2 mode.
Controls 12. VOLÏq (Volume Up/Down) Adjusts the sound level. 13. TV/PC Selects TV or PC mode directly. 14. PSM (Picture Status Memory) Recalls your preferred picture setting 15. SSM (Sound Status Memory) Recalls your preferred sound setting 16. ARC You can watch TV in various picture formats; Auto, 16:9, 14:9, 4:3, 16:9 Zoom, 14:9 Zoom, 4:3 Zoom. Repeatedly press the ARC button to select your desired picture format. Note.16:9 and 4:3 in PC mode and DTV mode are available. 17.
Basic Operation Turning the TV On and Off Standby Setup: The AC power cord must be set up and connected to have the TV in standby mode ready to be turned on. Press the ON/OFF button on the front panel of the TV to go into standby mode. 1. If the TV is in standby mode, press the POWER button on the remote controller or the TV itself to turn the TV on. 2. Press the Power button again on the remote controller or the ON/OFF button the TV itself to turn the TV off.
On Screen Menus and Displays 1. Press the MENU button to display main menu. 2. Press the PRxy button to select menus-Picture, Sound, Special, Setup. 3. Adjust each menu with the Ïq button. 4. Press the MENU button to return to preceding menu. 5. Press the TV/AV button to finish adjusting menu. Position :▲▼ Flat Music Movie Speech User 0.1 0.5 1.5 5.
Setting up TV Programme Once you have preset the programmes, you will be able to use the PRxy or NUMBER buttons to scan the programmes you programmed. Programmes can be tuned using automatic or manual modes. Auto Programme System Start BG Auto Programme All programmes that can be received are stored by this method. It is recommended that you use Auto programme during installation of this set. 1. Press the MENU button. 2. Select the Setup menu, then press the VOLq button. 3.
Setting up TV Programme Manual Programme Manual Programme Manual Programme lets you manually tune and arrange Programme the programmes in whatever order you desire. Also you Channel can assign a programme name with 5 characters to each Table System programme number. Search Memorize 1. Press the MENU button. Name 2. Select the Setup menu, then press the VOLq button. Position :▲▼ Back : MENU 3. Select Manual Programme menu, then press the VOLq button. 4.
Setting up TV Programme Programme Edit Programme Edit This function enables you to delete or skip the stored P00----P01----programmes. P02----Also you can move some programmes to other P03----P04----programme numbers or insert a blank programme data into ■Delete ■Move the selected programme number. Position :▲▼◀▶ 1. Press the MENU button. Back : MENU 2. Select the Setup menu, then press the VOLq button. 3. Press the PRxy button to select Programme Edit menu, then press the VOLq button. 4.
Picture Control You can adjust picture Contrast, Brightness, Colour, Sharpness and Tint(only in NTSC mode) to the levels you prefer. Manual Picture Control 1. Press the MENU button. 2. Select the Picture menu, then press the VOLq button. 3. Press the PRxy button select a picture item. 4. Press the Ïq button to adjust the picture condition as you want. 5. Press the TV/AV button to store for the picture User.
Sound Control You can select your preferred sound setting; Flat, Music, Movie or Speech. You can also adjust the sound frequency of equalizer, balance. If you switch AVL to on, the set automatically keeps on an equal volume level even if you change programmes. 1. Press the MENU button. 2. Select the Sound menu, then press the VOLq button. 3. Press the PRxy button to select the desired sound item; Equalizer, Balance, AVL, Surround or Sound Mode. 4. Press the Ïq button to make desired adjustment. 5.
Sound Control Auto Sound Control * The sound Flat, Music, Movie and Speech are programmed for good sound reproduction at the factory and cannot be changed. SSM (Sound Status Memory) 1. Press the SSM button. 2. Press the SSM button repeatedly to select. Each press of the button changes the screen display as below. Flat → Music → Movie → Speech → User • Choose Flat for the standard factory settings. • Choose Music when watching music video or concerts. • Choose Movie when watching movies.
Other functions You can control other functions; Clock, Blue Back, Auto Sleep, Childlock and ARC menu. Special Clock Setting the clock is necessary in order to use the various timer features of the TV. You can set automatic TV On or Off time. Clock Blue Back Auto Sleep Childlock ARC Position :▲▼ Back : MENU ▶ Off Off Off 16:9 Next :◀▶ Exit : TV/AV 1. Press the MENU button. 2. Press the PRxy button to select the Special menu. Then press the Ïq button. 3. Press the Ïq button to select Clock menu.
Other functions Auto Sleep If you select Auto Sleep On the set will automatically switch itself to standby mode approximately ten minutes after a TV Channel stops broadcasting. 1. Press the MENU button. 2. Select the Special menu. 3. Press the PRxy button to select Auto Sleep. 4. Press the Ïq button to select On. 5. Press the TV/AV button to return to normal TV viewing. Childlock Childlock menu is necessary in order to disable the buttons on the side panel of the set.
Other functions Calling the programme list You can check the programmes stored in the memory by displaying the programme LIST. Displaying programme list 1. Press the LIST button to display the Programme list menu. The programme list appears on the screen. One programme list contains ten programmes as right. Note : a. You may find some blue programmes. They have been set up to be skipped by auto programming or in the programme edit mode. b.
TELETEXT TEXT On/Off Press the TEXT/MIX button to switch to TELETEXT. The initial page or last selected page appears on the screen. The first page number indicates your selection, while the second shows the current page displayed. 1. Press TEXT/MIX button once, displays the Teletext pages. If you press the TEXT/MIX button twice, the teletext pages and the TV picture are concurrently displayed on both sides of the screen. 2.
TELETEXT Special TELETEXT functions MENU TEXT/MIX 22 Functions Changes Teletext mode. Only Teletext mode, text mode superimposed on the TV picture, TV mode. SIZE Selects double height text. Press this button to enlarge the top half of the page. Press this button again to enlarge the bottom half of the page. Press this button again to return to the normal display. HOLD Stops the automatic page change, which will occur if a Teletext page consists of 2 or more sub pages.
External Equipment Connection You can connect additional equipment, such as VCRs, camcorders etc. to your set. Examples are shown below. Antenna connection 1. Connect RF out on the VCR to the Antenna input on the rear of the TV. 2. Connect the antenna cable to the antenna in jack on the VCR. 3. Press the TV/AV button to select Antenna Input source. 4. Press the PLAY button on the VCR. COMPONENT1/DTV1 or COMPONENT2/DTV2 INPUT 1.
External Equipment Connection A/V INPUT 1. Connect the A/V out jacks on of the VCR to A/V- in jacks on the TV. 2. Press the TV/AV button to select VIDEO mode. 3. Press the PLAY button on the VCR. The VCR playback picture appears on the screen. Note. If you have a mono VCR, connect the audio cable from the VCR to the L(MONO) socket of set. Side of set Rear of set A/V OUT 1.
Connecting the PC as a monitor PC ANALOG(D-SUB) INPUT 1. Connect the PC ANALOG IN cable (D sub jack) from the monitor output socket of the PC to the PC/DTV input socket of the set. 2. Connect the PC Audio IN cable from the PC to the PC Audio IN of the set. 3. Press the TV/AV or TV/PC button to select PC ANALOG IN mode. 4. Switch on the PC, and the PC screen appears on the set. The set can be operated as the PC monitor. DVI (Digital Visual Interface) INPUT 1.
Connecting the PC as a monitor This function is possible only when the set is in PC mode. Use the TV/AV button on remote controller. Picture adjustment You can adjust picture Contrast, Brightness, Temperature, Clock, Phase and ARC as you prefer. 1. Press the TV/AV button to select the PC mode. 2. Press the MENU button. 3. Select the Picture, then press the VOLq button. 4. Press the PRxy button to select the desired picture item. 5. Press the Ïq button to make appropriate adjustments. 6.
Connecting the PC as a monitor Sound adjustment 1. Press the MENU button. Sound 2. Select the Sound menu, then press the VOLq button. Equalizer q 3. Press the PRxy button to select the desired Balance 0 AVL Off sound item; Equalizer, Balance, AVL, Surround or Surround Off Sound Mode. Sound Mode L+R 4. Press the Ïq button to make desired adjustment. 5. Press the Ïq button in Equalizer to set the Position :▲▼ Next :◀▶ Back : MENU Exit : TV/AV Equalizer. 6.
Connecting the PC as a monitor Position Adjustment This function is to adjust picture to left/right and up/down as you prefer. 1. Press the MENU button. 2. Select the H/V Position menu. 3. Press the PRxy button to select the desired position item. 4. Press the Ïq button to adjust horizontal position and vertical position. 5.
Product Specification Model NLT-23WQ Horizontal size Main body (With stand) Power requirements Height 600 mm 436.6(449) mm Thickness 91.4(190) mm Weight 100-240Va.c. 50/60Hz Television system PAL-BG, I, DK / SECAM-BG, DK, / NTSC-M Television programme VHF: 0~12 UHF :21~69 Cable : S1~S41 LCD Panel 23" WIDE TFT LCD panel Resolution WXGA Power consumption 9.
Troubleshooting Problem Check item No picture on screen and no sound from speakers • Insert the AC power cord plug securely in AC power outlet. • Make sure the set is not in the standby mode (The POWER/Standby indicator is red.) No picture/No picture from AV terminal • Check the brightness setting of the display. • Lamp may have malfunction. Picture is displayed, but no sound from the speakers. • Check the sound setting. • Make sure the sound is not muted.
NEC Australia Pty. Ltd.
NEC Australia Pty Ltd 104474 / 060329