Operation Manual
Table Of Contents
- INDEX
- Front cover
- Important Information
- Table of Contents
- 1. Introduction
- 2. Installation and Connections
- 3. Projecting an Image (Basic Operation)
- 4. Convenient Features
- (1) Turning Off the Image and Sound
- (2) Freezing a Picture
- (3) Enlarging and Moving a Picture
- (4) Changing Lamp Mode
- (5) Getting Integrated Help
- (6) Using a USB Mouse
- (7) Using the Optional Remote Mouse Receiver (NP01MR)
- (8) Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE]
- (9) Displaying Two Pictures at the Same Time
- (10) Preventing Unauthorized Use of the Projector
- (11) Limiting Access Level to Available Menu Items
- (12) Operation Using an HTTP Browser
- (13) Projecting Your Computer’s Screen Image from the Projector via a Network [NETWORK PROJECTOR]
- (14) Using the Projector to Operate Your Computer via a Network [REMOTE DESKTOP]
- 5. Using the Viewer
- 6. Using On-Screen Menu
- 7. Maintenance
- 8. Using Optional Lenses
- 9. Appendix
- (1) Troubleshooting
- (2) Specifications
- (3) Cabinet Dimensions
- (4) Screen Size and Projection Distance
- (5) Pin Assignments of D-Sub COMPUTER 1 Input Connector
- (6) Compatible Input Signal List
- (7) PC Control Codes and Cable Connection
- (8) Removing and Attaching the USB Wireless LAN Unit
- (9) Troubleshooting Check List
- (10) TravelCare Guide
114
To register a USB memory device as a protect key.
Preparation: Insert the USB memory device into the USB port (type A) of the projector.
1. Use the SELECT
or
button to select [USE PROTECT KEY] and press the ENTER button.
2. Use the SELECT
or
button to select [READ] and press the ENTER button.
Data of the USB memory will be read into the projector.
3. Use the SELECT
or
button to select [REGISTER] and press the ENTER button.
Downloaded data will be registered and be displayed in the list window.
4.
Use the SELECT
or
button to select [KEYWORD] and use the software keyboard to enter a keyword.
NOTE: Please make a note of your keyword.
5. Use the SELECT
or
button to select [OFF] and then use the SELECT
or
to select [ON].
6. Use the SELECT
or
button to select [OK] , then press the ENTER button.
The [ARE YOU SURE?] message will appear.
7. Use the SELECT
or
button to select [YES] and press the ENTER button.
The Security function takes effect.
To turn on the projector when Security is enabled (when using your keyword only).
1. Press and hold the POWER button for a minimum of two seconds.
The projector will be turned on and a message to the effect that the projector is security-protected will
be displayed.
2. Press the MENU button.
The Release Code input screen will be displayed.
3. Enter your keyword in the Release Code input screen.
You can view the projected image.
NOTE: Do not forget your keyword. However, if you forget your keyword, NEC or your dealer will provide you with your Release
Code. See more information at the end of this section.
To turn on the projector when Security is enabled (when using USB memory device as a protect
key).
Preparation: Insert the registered USB memory device into the USB port (type A) of the projector.
Press and hold the POWER button for a minimum of two seconds.
The projector will turn on and then recognize the USB memory device. Once the image has been projected, it will
stay on without the USB memory device.
• The projector does not support NTFS formatted USB memory device.
Be sure to use a USB memory device formatted with the FAT32, FAT16 or FAT file system.
To format your USB memory device in your computer, refer to the document or help file that comes with your
Windows.
• We do not warrant that the USB port of the projector will support all USB memory devices in the market.
• When the projector is turned on, if the registered USB memory device is not inserted into the projector, no
signal will be displayed with a message to the effect that the projector is security-protected. To turn off the se-
curity protection, insert the registered USB memory device into the projector.
6. Using On-Screen Menu