Operation Manual
Table Of Contents
- INDEX
- Front cover
- Important Information
- Table of Contents
- 1. Introduction
- 2. Installation and Connections
- 3. Projecting an Image (Basic Operation)
- 4. Convenient Features
- (1) Turning Off the Image and Sound
- (2) Freezing a Picture
- (3) Enlarging and Moving a Picture
- (4) Changing Lamp Mode
- (5) Getting Integrated Help
- (6) Using a USB Mouse
- (7) Using the Optional Remote Mouse Receiver (NP01MR)
- (8) Correcting Horizontal and Vertical Keystone Distortion [CORNERSTONE]
- (9) Displaying Two Pictures at the Same Time
- (10) Preventing Unauthorized Use of the Projector
- (11) Limiting Access Level to Available Menu Items
- (12) Operation Using an HTTP Browser
- (13) Projecting Your Computer’s Screen Image from the Projector via a Network [NETWORK PROJECTOR]
- (14) Using the Projector to Operate Your Computer via a Network [REMOTE DESKTOP]
- 5. Using the Viewer
- 6. Using On-Screen Menu
- 7. Maintenance
- 8. Using Optional Lenses
- 9. Appendix
- (1) Troubleshooting
- (2) Specifications
- (3) Cabinet Dimensions
- (4) Screen Size and Projection Distance
- (5) Pin Assignments of D-Sub COMPUTER 1 Input Connector
- (6) Compatible Input Signal List
- (7) PC Control Codes and Cable Connection
- (8) Removing and Attaching the USB Wireless LAN Unit
- (9) Troubleshooting Check List
- (10) TravelCare Guide
151
9. Appendix
Removing and Attaching the USB Wireless LAN Unit
Insert the optional USB Wireless LAN Unit into the USB Wireless LAN Unit port on the rear panel of the projector.
Important
• The USB Wireless LAN Unit consists of two modules: a Wireless LAN module (USB) and a joint module.
• Do not insert other USB devices into the USB Wireless LAN unit port.
• Do not insert the USB Wireless LAN unit into the USB port (Type A).
• The USB Wireless LAN Unit must be inserted into the USB Wireless LAN Unit port in the correct direction.
It cannot be inserted in the reverse direction. If the USB Wireless LAN Unit is inserted in the reverse direction
with excessive force applied, the USB port may break.
• Before touching the USB Wireless LAN Unit, touch a metallic object (such as a door knob or aluminum window
frame) to discharge the static electricity from your body.
• Always insert or remove the USB Wireless LAN unit when the main power is turned off. Failure to do so may
cause projector malfunction or damage to the USB wireless LAN unit. If the projector will not work correctly, turn
off the projector, wait 30 seconds, and turn it back on.
• The blue LED on the Wireless LAN Unit flashes to show that Wireless LAN Unit is working.
• If the Wireless LAN Unit is attached incorrectly, the blue LED will not light.
To attach the optional USB Wireless LAN Unit to the USB Wireless LAN unit port, follow the in-
structions below.
1. Press POWER ON/STAND BY button to set the projector to Stand-by mode, then press the “O (off)” side
of the main power switch of the projector.
2. Loosen and remove two screws.
L
A
M
P
S
T
A
T
U
S
P
O
W
E
R
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
U
S
T
3
D
R
E
F
O
R
M
SELEC
T
U
S
B
L
E
N
S
S
H
I
F
T
L
E
F
T
R
I
G
H
T
DO
W
N
U
P
WIRELESS
WIRELESS