Installation and Setup Guide

ManualsBrandsNEC ManualsMultimedia ProjectorsNEC NP-M282X

ISSUED: 04-11-06 SHEET #: 055-9458-2 05-09-06

Visit the NEC Web Site at www.necsam.com

1 of 9

For customer care call 1-800-729-0307 or 708-865-8870.

Read instruction sheet before you start installation and assembly.

Maximum Load Capacity: 50 lb (22.7 kg)

IMPORTANT! Be sure not to touch the projector while tightening the set screw on the

ball and socket mount. This may cause the image to be unaligned when you let go.

Applications:

Flush Mount .................................................................................................................................................. page 7

Extension Column ........................................................................................................................................ page 8

Installations:

To Wood Joist Finished Ceilings,

Exposed Wood Joists, or Wood Beam Ceilings........................................................................................ page 5

To Concrete Ceilings.................................................................................................................................... page 6

IMPORTANT! Turn to the appropriate page for your ceiling installation.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and

components.

WARNING

Model: NP01UCM

Installation and Assembly - Universal Ceiling Mount

Summary of content (9 pages)

PAGE 1
Installation and Assembly - Universal Ceiling Mount Model: NP01UCM Maximum Load Capacity: 50 lb (22.7 kg) Read instruction sheet before you start installation and assembly. WARNING • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. IMPORTANT! Be sure not to touch the projector while tightening the set screw on the ball and socket mount. This may cause the image to be unaligned when you let go.
PAGE 2
Compatability Chart for NEC Projectors Manufacturer Model Manufacturer Model NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC HT410 HT510 GT1150 GT2150 GT5000 GT6000 GT6000R GT2000 GT2000R GT950 LT10 LT140 LT84 LT150 LT150z NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC MT1035 MT1035+ MT830 MT830+ MT1040 MT1045 MT840 MT850 MT1050 MT1055 MT1056 MT860 MT1060 MT1060R MT1065 NEC LT75 NEC Multisync LT245 NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC NEC N
PAGE 3
Before you start check the parts list to insure all of the parts shown are included. Parts List Description Qty. Part Number A ball and socket mount 1 055-0016 B 4 mm security allen wrench 1 560-9646 C M5 x .8 x 10 mm socket pin type F screw 1 520-2031 D #10-32 x 3/8" spade thumb screw 1 560-2107 E #10-32 x 3/8" serrated washer head socket pin screw 1 520-2151 F #14 x 2.5 phillips hex head wood screw 2 5S1-015-C04 G ceiling plate 1 580-4042 H .25" ID x .56" OD x .
PAGE 4
Installation and assembly - Universal Adapter Plate Note: The projector you are installing may differ in appearance from the sample illustrated below. Place projector upside down. Locate adapter plate (L) with notch facing forward as close to projector center of gravity as possible without covering any mounting holes. Loosen channels, and if there are only three mounting holes remove fourth channel. Using one channel for each mounting hole, position feet of channels over mounting holes as shown below.
PAGE 5
Installation To Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate (G) with two #14 x 2.5" (6 mm x 65 mm) wood screws (F) as shown using 3/8" (10 mm) socket wrench. WOOD JOIST Skip to step 2. WARNING CEILING • Tighten wood screws (F) so that wall plate (G) is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
PAGE 6
WARNING • When installing wall mounts on concrete, verify that you have a minimum of 1 5/8" of actual concrete surface in the 1/ 4" diameter hole to be used for the concrete anchors. Do not drill into mortar joints! Concrete must meet ASTM C-90 specifications. • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
PAGE 7
Flush Mount Application Screw ball and socket mount (A) into ceiling plate (G). Align the notch with one of the four holes of the ceiling plate (G) and secure ball and socket mount (A) with a M5 x 10 mm socket pin screw (C) using security allen wrench (B) as shown in detail 1. Note: Slotted set screw (K) is used to jam against the threads of the ball and socket mount to prevent any excess movement of the ball and socket mount (A).
PAGE 8
Installation to Extension Column G Screw extension column to ceiling plate (G). Align the notch with one of the four holes in the ceiling plate (G) and secure extension column with a M5 x 10 mm socket pin screw (C) using security allen wrench (B). See detail 4. G EXTENSION COLUMN (UL Listed EXT or ADJ Series) Sold Separately Screw extension column connector (I) to extension column. Align slot in extension column with one of the top holes in extension column connector (I).
PAGE 9
Note: The projector adapter plate and projector you are installing may differ in appearance from the sample illustrated below. Attach projector, with adapter plate already on it, to the ball and socket mount (A) by inserting the ball and socket mount (A) into the adapter plate connection and twisting until the adapter plate will no longer turn (about 75°).