Installation and Setup Guide

ManualsBrandsNEC ManualsMultimedia ProjectorsNEC NP-P501X

ISSUED: 10-01-10 SHEET #: 056-9034-4 07-29-11

Visit the Peerless Web Site at www.peerlessmounts.com

1 of 10

For customer care call 1-800-865-2112

Installation and Assembly Manual:

Custom Ceiling Mount for NEC M260X, M260W, M271X, M300X,

M300W M300XS, M300WS, M311X, M311W, P350X, P350W, P420X

Projectors

Model: MP300CM

Features:

• ImageLock

alignmentpreventspicturesagordrift

• Wrenchaccessslotforeasierushmountinstallations

• Exclusivealuminumtrackquickrelease

NECDisplaySolutionsofAmerica,Inc.

Max UL Load Capacity:50lb(22.7kg)

Summary of content (10 pages)

PAGE 1
NEC Display Solutions of America, Inc. Installation and Assembly Manual: Custom Ceiling Mount for NEC M260X, M260W, M271X, M300X, M300W M300XS, M300WS, M311X, M311W, P350X, P350W, P420X Projectors Model: MP300CM Features: • ImageLockTM alignment prevents picture sag or drift • Wrench access slot for easier flush mount installations Max UL Load Capacity: 50 lb (22.7 kg) • Exclusive aluminum track quick release 1 of 10 Visit the Peerless Web Site at www.peerlessmounts.
PAGE 2
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.
PAGE 3
Before you start check the parts list to insure all of the parts shown are included. Parts List A B C D E F G AA BB CC DD EE Description projector mount assembly 4 mm security allen wrench #10-32 x 3/8" serrated washer head socket pin screw #10-32 x 1/4" socket pin screw flat washer #14 x 2.5 phillips hex head wood screw concrete anchor adapter plate M4 x 16 mm serrated socket pin screw retaining spacer 2 mm allen wrench connection block Qty.
PAGE 4
Installation to Extension Column / Ceiling Plate 1 NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to ceiling. Screw projector mount assembly (A) onto extension column as shown in figure 1.1. Tighten swivel stop screw against extension column, flush mount tube or reducer using 4 mm security allen wrench (B) as shown in figure 1.2.
PAGE 5
Installation To Wood Joist Ceilings WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud.
PAGE 6
Installation to Concrete Ceilings WARNING • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. 3 Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes. Drill two 5/16" (8mm) dia. holes to a minimum depth of 2-1/2" (64mm).
PAGE 7
Installation to Threaded Rod (Not evaluated by UL - Professional installation only) 4 Thread two 1/4-20 hex thin nylon-insert locknuts (not included) on two 1/4-20 threaded rods (not included) to the desired height of projector mount assembly. Attach projector mount assembly (A) to the two 1/4-20 threaded rods using two 1/4-20 hex thin nylon-insert locknuts as shown in figure 4.1 or figure 4.2.
PAGE 8
Attaching Adapter Plate to Projector 5 Align shoulder on connection block (EE) opposite notch in adapter plate (AA). Attach adapter plate (AA) to connection block (EE) using two #10-32 x 3/8" serrated washer head socket pin screws (C) as shown in figure 5.1. Tighten screws using 4 mm allen wrench (B). EE NOTCH INDICATES FRONT OF PROJECTOR SHOULDER AA C fig. 5.
PAGE 9
Attaching Adapter Plate to Projector Mount WARNING • Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the screen. 7 Slide connection block (EE) with projector into projector mount assembly (A) as shown. Tighten captive screw to secure projector to projector mount assembly (A).
PAGE 10
Projector Alignment 9 To adjust yaw (swivel) for wood stud, concrete ceiling, and threaded rod mounting applications: Loosen wood screws (F) if flush mounted to wood joists (page 5) or concrete ceilings (page 6), or loosen locknuts on threaded rods (page 7), until projector mount can be rotated. Rotate mount to desired position and retighten screws or locknuts.