Installation and Setup Guide

ManualsBrandsNEC ManualsProjectorsNP-PX602UL-BK

1 of 8

ISSUED: 09-15-11 SHEET #:125-9244-1

Model: NP750CM

Installation and Assembly:

Projector Adapter Plate

• Itistheresponsibilityoftheinstallertoensure

thattheprojectorisproperlyventilated.Spacers

areprovidedtoraisethemountofftheprojector

surface.

CAUTION

• Installermustverifythattheceilingwillsafely

supportfourtimesthecombinedweightofall

attachedequipmentandhardware.

WARNING

Model: PX750CM

Installation and Assembly:

Adapter Plate for NEC Projector

Model PX-750U

IMPORTANT! Read entire instruction sheet before you start installation and assembly.

Max Load Capacity:

60lb(22.3kg)

Summary of content (8 pages)

PAGE 1
Installation and Assembly: Adapter Plate for NEC Projector Model PX-750U Model: PX750CM IMPORTANT! Read entire instruction sheet before you start installation and assembly. Installation and Assembly: Projector Adapter Plate Model: NP750CM Max Load Capacity: 60 lb (22.3 kg) WARNING CAUTION • It is the responsibility of the installer to ensure that the projector is properly ventilated. Spacers are provided to raise the mount off the projector surface.
PAGE 2
NOTE: Read entire instruction sheet before you start installation and assembly. A Parts List A B C D E F G H I J K L M N O P Q R S Description adapter assembly M4 x 12 mm socket pin serrated washer head screw M5 x 10 mm socket pin serrated washer head screw M4 x 40 mm socket pin serrated washer head screw 4 mm allen wrench .375 spacer .75 spacer projector mount assembly column connector ceiling plate .25" x .5" x .
PAGE 3
Installation To Wood Joist Finished Ceilings, Exposed Wood Joists, or Wood Beam Ceilings 1 Drill two 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling plate (J) to ceiling with two #14 x 2.5" wood screws (Q) using 3/8" (10 mm) socket wrench as shown in figure 1.1. WOOD JOIST NOTE: For optional cord management, install two spacers (K) between ceiling plate (J) and ceiling as shown in figure 1.2. Skip to step 2 for flush mount installation.
PAGE 4
Installation to Concrete Ceilings WARNING • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. 1 Drill two 5/16" (8 mm) dia. holes to a minimum depth of 2.5" (64 mm). Insert anchors (O) in holes flush with wall. Place ceiling plate (J) over anchors and secure using two #14 x 2.5" screws (Q).
PAGE 5
Flush Mount Installation 2 Hand thread projector mount assembly (H) into ceiling plate (J) as shown in figure 2.1. Align the notch of projector mount assembly with one of the four holes in ceiling plate (J) and secure with an M5 x 10 mm socket pin screw (S) as shown in detail 1. NOTE: Slotted set screw (N) is used to jam against the threads of the projector mount assembly to prevent any excess movement of the projector mount assembly (H).
PAGE 6
Extension Column Installation 3 J Hand thread extension column into ceiling place (J). Align notch of extension column with one of the four holes in ceiling plate (J) and secure with an M5 x 10 mm socket pin screw (S) using allen wrench (E) as shown in detail 2. N Hand thread column connector (I) onto extension column. Align slot in extension column with one of the top holes of the column connector (I).
PAGE 7
4 Fasten adapter assembly (A) to bottom of projector using two M4 x 40 mm socket pin serrated washer head screws (D) with spacers (F and G), and four M4 x 12 mm socket pin serrated washer head screws (B) in orientation as shown below. D B A F G FRONT OF PROJECTOR M4 X 40 MM SOCKET PIN SERRATED WASHER HEAD SCREW (D), WITH SPACERS (F AND G) FRONT OF PROJECTOR M4 X 12 MM SOCKET PIN SERRATED WASHER HEAD SCREW (B) 5 Handles can be pulled out for additional leverage as shown below.
PAGE 8
Attaching Adapter Plate to Projector Mount 7 Attach projector to projector mount assembly (H) by inserting the mount into the adapter plate and twisting until the adapter plate will no longer turn. The spring loaded captive screw should line up with a corresponding hole on the adapter plate. Push down and tighten the spring loaded captive screw to secure the adapter plate to the mount. If not using the optional security feature, fasten thumb screw (L) in the hole opposite the spring loaded captive screw.