Portable Projector UM351W/UM301W/ UM361X/UM301X User’s Manual The UM301W and UM301X are not distributed in North America. Model No.
Ver. 1 10/14 • Apple, Mac, Mac OS, MacBook, and iMac are trademarks of Apple Inc. registered in the U.S. and other countries. • Microsoft, Windows, Windows Vista, Internet Explorer, .NET Framework and PowerPoint are either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. • Intel and Intel Core are trademarks of Intel Corporation in the U.S. and/or other countries.
Important Information Safety Cautions Precautions Please read this manual carefully before using your NEC projector and keep the manual handy for future reference. CAUTION To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible. CAUTION TO PREVENT SHOCK, DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Important Information WARNING TO CALIFORNIA RESIDENTS: Handling the cables supplied with this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING. RF Interference (for USA only) WARNING The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Display Solutions of America, Inc. in this manual.
Important Information WARNING • Do not place any objects, which are easily affected by heat, in front of the projection window. Doing so could lead to the object melting from the heat that is emitted from the light output. • Do not use a spray containing flammable gas to get rid of accumulated dust and dirt on the filters and the projection window. It may cause of fire.
Important Information the projector, unplug the power cord and have the projector serviced by a qualified service personnel. • Handle the power cord carefully. A damaged or frayed power cord can cause electric shock or fire. - Do not use any power cord other than the one supplied with the projector. - Do not bend or tug the power cord excessively. - Do not place the power cord under the projector, or any heavy object. - Do not cover the power cord with other soft materials such as rugs.
Important Information Note for US Residents The lamp in this product contains mercury. Please dispose according to Local, State or Federal Laws. Lamp Replacement • Use the specified lamp for safety and performance. • To replace the lamp, follow all instructions provided on page 122. • Be sure to replace the lamp and filter when the message [THE LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP AND FILTER.] appears.
Important Information Power management function The projector has power management functions. To reduce power consumption, the power management functions (1 and 2) are factory preset as shown below. To control the projector from an external device via a LAN or serial cable connection, use the on-screen menu to change the settings for 1 and 2. 1. STANDBY MODE (Factory preset: NORMAL) To control the projector from an external device, select [NETWORK STANDBY] for [STANDBY MODE].
Table of Contents Important Information. ...........................................................................................i 1. Introduction........................................................................................................... 1 1 What’s in the Box?.......................................................................................................... 1 Introduction to the Projector...........................................................................................
Table of Contents Pincushion.............................................................................................................. 31 Preventing the Unauthorized Use of the Projector [SECURITY]....................................... 33 Using the Computer Cable (VGA) to Operate the Projector (Virtual Remote Tool)...... 36 Operating Your Computer’s Mouse Functions from the Projector’s Remote Control via the USB Cable (Remote Mouse Function)........................................................
Table of Contents [SOURCE(1)]........................................................................................................ 100 [SOURCE(2)]........................................................................................................ 100 [WIRED LAN]........................................................................................................ 100 [WIRELESS LAN]................................................................................................. 101 [VERSION].........
1. Introduction 1 What’s in the Box? Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Please save the original box and packing materials if you ever need to ship your projector.
1. Introduction Introduction to the Projector This section introduces you to your new projector and describes the features and controls. Features you’ll enjoy: • Ultra short throw distances Ultra short focal lenses provide for a larger image using a shorter throw distance when compared to a typical projector lens. UM361X/UM301X: Max 116.
1. Introduction • Correspond to various installation Besides installation on the wall, it can correspond various installation as projecting image up onto the ceiling , onto the table, and onto the floor, etc. • The supplied remote control allows you to assign a CONTROL ID to the projector Multiple projectors can be operated separately and independently with the same single remote control by assigning an ID number to each projector.
1. Introduction Part Names of the Projector Top and Screen Side of Projector Projection Window Intake Vent/Filter (→ page 118, 125) Security chain opening Attach an anti-theft device. The security chain opening accepts security wires or chains up to 0.18 inch/4.6 mm in diameter.
1. Introduction Removing and Attaching the Cable Cover After finishing connections, attach the supplied cable cover to properly hide the cables. CAUTION: • Be sure to tighten the screws after attaching the cable cover. Failure to do so may cause the cable cover to come off and fall, resulting in injury or damage to the cable cover. • Do not put bundled cables in the cable cover. Doing so may damage the power cord, resulting in a fire.
1. Introduction Attaching the cable cover 1. Align four tabs of the cable cover with grooves of the projector and push the cable cover until you click it. NOTE: • Be careful not to get cables caught in between the cable cover and the projector. 2. Tighten the cable cover screws. • Be sure to tighten the screws.
1. Introduction Top Features 5 7 9 10 8 11 6 3 1, 2 1. 4 (POWER) Button (→ page 14, 24) 2. POWER Indicator (→ page 13, 14, 24, 128) 3. STATUS Indicator (→ page 128) 4. LAMP Indicator (→ page 122, 128) 5. ECO Button (→ page 27) 6. SOURCE Button (→ page 16) 7. AUTO ADJ. Button (→ page 23) 8. MENU Button (→ page 72) 9. / Volume Buttons / Keystone Buttons (→ page 15, 21, 23, 72) 10. ENTER Button (→ page 72) 11.
1. Introduction Terminal Panel Features 12 13 5 11 4 3 1 2 14 7 8 6 1. COMPUTER IN/ Component Input Terminal (Mini D-Sub 15 Pin) (→ page 106, 110, 113) 2. COMPUTER AUDIO IN Mini Jack (Stereo Mini) (→ page 106, 107, 110) 3. HDMI 1/MHL IN Terminal (Type A) (→ page 106, 107, 111, 112) 4. HDMI 2 IN Terminal (Type A) (→ page 106, 107, 111) 5. USB (PC) Port (Type B) (→ page 42, 43, 106) 6. MONITOR OUT (COMPUTER) Terminal (Mini D-Sub 15 Pin) (→ page 108) 7.
1. Introduction Part Names of the Remote Control 1 3 4 10. DisplayPort Button 2 (→ page 16) 6 11. VIDEO Button (→ page 16) 7 5 12. USB-A Button (→ page 16, 66, 68) 10 8 13. USB-B Button (→ page 16, 106) 16 9 14. LAN Button (→ page 16) 13 11 15. ID SET Button 15 12 (→ page 91) 14 17 16. Numeric Keypad Button/CLEAR Button 18 20 (→ page 91) 19 21 17. FREEZE Button 22 (→ page 26) 26 18. AV-MUTE Button 23 28 (→ page 26) 25 19. MENU Button 24 29 (→ page 72) 27 20. EXIT Button (→ page 72) 30 21.
1. Introduction Battery Installation 1 Press firmly and slide the battery cover off. 2 Install new batteries (AAA). Ensure that you have the batteries’ polarity (+/−) aligned correctly. 3 Slip the cover back over the batteries until it snaps into place. Do not mix different types of batteries or new and old batteries. EN OP EN OP Remote Control Precautions • • • • • • • • • Handle the remote control carefully. If the remote control gets wet, wipe it dry immediately.
1. Introduction Software Included on CD-ROM Names and Features of Bundled Software Programs Name of software program Virtual Remote Tool (Windows only) Features This is a software program used to control the power ON/OFF and source selection of the projector from your computer by using the supplied computer cable (VGA) and others.
2. Projecting an Image (Basic Operation) This section describes how to turn on the projector and to project a picture onto the screen.
2. Projecting an Image (Basic Operation) Connecting Your Computer/Connecting the Power Cord 1. Connect your computer to the projector. This section will show you a basic connection to a computer. For information about other connections, see “6. Installation and Connections” on page 106. Connect the computer cable (VGA) between the projector’s COMPUTER IN terminal and the computer’s port (mini D-Sub 15 Pin). Turn two thumb screws of both terminals to fix the computer cable (VGA). 2.
2. Projecting an Image (Basic Operation) Turning on the Projector • Press the (POWER) button on the projector cabinet or the POWER ON button on the remote control. The POWER indicator will blink and the projector will become ready to use. TIP: • When the message “Projector is locked! Enter your password.” is displayed, it means that the [SECURITY] feature is turned on.
2. Projecting an Image (Basic Operation) Note on Startup screen (Menu Language Select screen) When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the 30 menu languages. To select a menu language, follow these steps: 1. Use the , H, F or E button to select one of the 30 languages from the menu. 2. Press the ENTER button to execute the selection. After this has been done, you can proceed to the menu operation.
2. Projecting an Image (Basic Operation) Selecting a Source Selecting the computer or video source NOTE: Turn on the computer or video source equipment connected to the projector. Detecting the Signal Automatically Press the SOURCE button once. The projector will search for the available input source and display it.
2. Projecting an Image (Basic Operation) Adjusting the Picture Size and Position Use the adjustable tilt foot, the zoom function or the focus ring to adjust the picture size and position. In this chapter drawings and cables are omitted for clarity.
2. Projecting an Image (Basic Operation) Adjusting horizontal/vertical position The throw distance can affect the size and the height of the projected image. Before installing the projector, decide the throw distance according to “Setting Up the Screen and the Projector” (→ page 103, 104) It is recommended to display the test pattern while adjusting the image. (→ page 92) 1. Move the projector back and forth and left and right so that the image fits the screen width.
2. Projecting an Image (Basic Operation) Adjusting the tilt (Tilt foot) Adjusting the left and right tilt. 1. Rotate the tilt foot to adjust the left and right tilt. The tilt foot is equipped at the left and the right front bottom of the projector. If the projected image is tilted, rotate one of the tilt foot to adjust the angle to project.
2. Projecting an Image (Basic Operation) Adjusting the size [Digital Zoom] Use the remote control to finely adjust the size of the image. 1. Press the FOCUS/ZOOM button on the remote control. The DIGITAL ZOOM bar will be displayed. 2. Press the or button to finely zoom in or out. 3. After completing the adjustment, press the ENTER button. The DIGITAL ZOOM bar will be closed.
2. Projecting an Image (Basic Operation) ❻ Correcting Keystone Distortion [KEYSTONE] When the projector is not exactly perpendicular to the screen, keystone distortion occurs. To overcome it, you can use the “Keystone” function, a digital technology that can adjust for keystone-type distortion, resulting in a crisp, square image. The following procedure explains how to use the [KEYSTONE] screen from the menu to correct trapezoidal distortions.
2. Projecting an Image (Basic Operation) 4. Press the ▲ button to select [HORIZONTAL] and then use the ◀ or ▶ so that the top and bottom sides of the projected image are parallel. • Adjust the horizontal keystone distortion. 5. Repeat steps 2 and 4 to correct keystone distortion. 6. After completing Keystone correction, press the EXIT button. The Keystone screen will disappear. • To perform Keystone correction again, press the ▼ button to display the Keystone screen and repeat above steps 1 to 6.
2. Projecting an Image (Basic Operation) Optimizing Computer Signal Automatically Adjusting the Image Using Auto Adjust Optimizing a computer image automatically. (COMPUTER) Press the AUTO ADJ. button to optimize a computer image automatically. This adjustment may be necessary when you connect your computer for the first time. [Poor picture] [Normal picture] NOTE: Some signals may take time to display or may not be displayed correctly.
2. Projecting an Image (Basic Operation) Turning off the Projector To turn off the projector: 1. First, press the (POWER) button on the projector cabinet or the STANDBY button on the remote control. The confirmation message will be displayed. 2. Secondly, press the ENTER button or press the (POWER) or the STANDBY button again. The lamp will turn off and the projector will go into standby mode.
2. Projecting an Image (Basic Operation) When Moving the Projector Preparation: Make sure that the projector is turned off. 1. Remove the cable cover. (→ page 5) 2. Unplug the power cord. 3. Disconnect any other cables. • Remove the USB memory or the wireless LAN Unit if it is inserted into the projector.
3. Convenient Features 1 Turning off the Image and Sound Press the AV-MUTE button to turn off the image and sound for a short period of time. Press again to restore the image and sound. The projector’s power-saving function will work 10 seconds after the image is turned off. As a result, the lamp power will be reduced. NOTE: • Even though the image is turned off, the menu still remains on the screen. • Sound from the AUDIO OUT jack (Stereo mini) can be turned off.
3. Convenient Features 2. Press the button. The area of the magnified image will be moved 3. Press the D-ZOOM (−) button. Each time the D-ZOOM (−) button is pressed, the image is reduced. NOTE: • The image will be magnified or demagnified at the center of the screen. • Displaying the menu will cancel the current magnification.
3. Convenient Features NOTE: • The [ECO MODE] can be changed by using the menu. Select [SETUP] → [GENERAL] → [ECO MODE]. • The lamp life remaining and lamp hours used can be checked in [USAGE TIME]. Select [INFO.] →[USAGE TIME]. • The projector is always in [NORMAL] for 90 seconds after the lamp is turned on and while the POWER indicator is blinking green. The lamp condition will not be affected even when [ECO MODE] is changed.
3. Convenient Features ❺ Using 4-Point Corner to Correct Keystone Distortion [CORNERSTONE] Use the [CORNERSTONE] and [PINCUSHION] features to correct keystone (trapezoidal) distortion to make the top or bottom and the left or right side of the screen longer or shorter so that the projected image is rectangular. Cornerstone 1. Press the KEYSTONE button with no menu displayed. The KEYSTONE screen will be displayed. • Press the KEYSTONE button when using the remote control. • See page for PINCUSHION.
3. Convenient Features 7. Use the ▲▼◀▶ button to move the projected image frame as shown on the example. 8. Press the ENTER button. 9. Use the ▲▼◀▶ button to select another icon which points in the direction. On the Cornerstone adjustment screen, select [EXIT] or press the EXIT button on the remote control. The confirmation screen is displayed. 10. Press the ◀ or ▶ button to highlight the [OK] and press the ENTER button. This completes the Cornerstone correction.
3. Convenient Features Pincushion 1. Press the KEYSTONE button with no menu displayed. The KEYSTONE screen will be displayed. • Press the KEYSTONE button when using the remote control. 2. Press the button to select either PINCUSHION ADJUSTMENT LEFT/RIGHT or PINCUSHION ADJUSTMENT TOP/BOTTOM. 3. Press either or button to reform pincushion distortion. 4. Press the EXIT when PINCUSHION adjustment is completed.
3. Convenient Features 2. Move the cursor onto YES using either or button and then press the ENTER. NOTE: • All adjusted values set in the KEYSTONE adjustment are reset to initial values TIP: Adjustable range of the KEYSTONE and the CORNERSTONE: Horizontal Direction CORNERSTONE Approx. ±10° (Max) KEYSTONE Adjustable range may be narrower depending on input signal. 32 Vertical Direction Approx.
3. Convenient Features Preventing the Unauthorized Use of the Projector [SECURITY] A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the projector cannot project an image. • The [SECURITY] setting cannot be cancelled by using the [RESET] of the menu. To enable the Security function: 1. Press the MENU button.
3. Convenient Features 7. Type in the same combination of buttons and press the ENTER button. The confirmation screen will be displayed. 8. Select [YES] and press the ENTER button. The SECURITY function has been enabled. To turn on the projector when [SECURITY] is enabled: 1. Press the POWER button. The projector will be turned on and display a message to the effect that the projector is locked. 2. Press the MENU button. 3. Type in the correct keyword and press the ENTER button.
3. Convenient Features To disable the SECURITY function: 1. Press the MENU button. The menu will be displayed. 2. Select [SETUP] → [INSTALLATION] → [SECURITY] and press the ENTER button. The OFF/ON menu will be displayed. 3. Select [OFF] and press the ENTER button. The SECURITY KEYWORD screen will be displayed. 4. Type in your keyword and press the ENTER button. When the correct keyword is entered, the SECURITY function will be disabled. NOTE: If you forget your keyword, contact your dealer.
3. Convenient Features Using the Computer Cable (VGA) to Operate the Projector (Virtual Remote Tool) Using the utility software “Virtual Remote Tool” included on the companion NEC Projector CD-ROM, Virtual Remote screen (or toolbar) can be displayed on your computer screen. This will help you perform operations such as projector’s power on or off and signal selection via the computer cable (VGA), serial cable, or LAN connection.
3. Convenient Features NOTE: • When [COMPUTER] is selected from your source selection, the Virtual Remote screen or the toolbar will be displayed as well as your computer screen. • Use the supplied computer cable (VGA) to connect the COMPUTER IN terminal directly with the monitor output terminal of the computer to use Virtual Remote Tool. Using a switcher or other cables than the supplied computer cable (VGA) may cause failure in signal communication. VGA cable terminal: Pin Nos.
3. Convenient Features TIP: If the menu window will not be displayed, try the following procedure. For Windows 7 1. Click “start” on Windows. 2. Click “All Programs” → “Accessories” → “Run”. 3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\ LAUNCHER.EXE) 4. Click “OK”. The menu window will be displayed. 2 Click “Install Virtual Remote Tool” on the menu window. The installation will start.
3. Convenient Features TIP: Uninstalling Virtual Remote Tool Preparation: Exit Virtual Remote Tool before uninstalling. To uninstall Virtual Remote Tool, the Windows user account must have “Administrator” privilege (Windows 8.1, Windows 8, Windows 7 and Windows Vista) or “Computer Administrator” privilege (Windows XP). • For Windows 8.1, Windows 8, Windows 7 and Windows Vista 1 Click “Start” and then “Control Panel”. The Control Panel window will be displayed.
3. Convenient Features Step 3: Start Virtual Remote Tool Start using the shortcut icon • Double-click the shortcut icon on the Windows Desktop. Start from the Start menu • Click [Start] → [All Programs] or [Programs] → [NEC Projector User Supportware] → [Virtual Remote Tool] → [Virtual Remote Tool]. When Virtual Remote Tool starts for the first time, “Easy Setup” window will be displayed.
3. Convenient Features Exiting Virtual Remote Tool 1 Click the Virtual Remote Tool icon on the Taskbar. The pop-up menu will be displayed. 2 Click “Exit”. The Virtual Remote Tool will be closed. Viewing the help file of Virtual Remote Tool • Displaying the help file using the taskbar 1 Click the Virtual Remote Tool icon on the taskbar when Virtual Remote Tool is running. The pop-up menu will be displayed. 2. Click “Help”. The Help screen will be displayed.
3. Convenient Features Operating Your Computer’s Mouse Functions from the Projector’s Remote Control via the USB Cable (Remote Mouse Function) The built-in remote mouse function enables you to operate your computer’s mouse functions from the supplied remote control when the projector is connected to a computer via a commercially available USB cable (compatible with USB 2.0 specifications). The Remote Mouse function works for the COMPUTER input while the computer screen is displayed.
3. Convenient Features Projecting Your Computer’s Screen Image from the Projector via the USB Cable (USB Display) Using a commercially available USB cable (compatible with USB 2.0 specifications) to connect the computer with the projector allows you to send your computer screen image to the projector for displaying. Power On/Off and source selection of the projector can be done from your computer without connecting a computer cable (VGA).
3. Convenient Features 5. Operate the control window. (6) (1) (2) (3) (4) (5) (1) (Source) ����� Selects an input source of the projector. (2) (Picture) ���� Turns on or off AV-MUTE (Picture mute), and turns on or off FREEZE (Freeze a picture). (3) (Sound) ����� Turns on or off AV-MUTE (Sound mute), play the sound and turns up or down the volume. (4) (Others) ����� Uses “Update”, “HTTP Server”*, “Settings” and “Information”. * The HTTP Server cannot be selected when a USB cable is connected.
3. Convenient Features Controlling the Projector by Using an HTTP Browser Overview The HTTP Server function provides settings and operations for: 1. Setting for wired/wireless network (NETWORK SETTINGS) To use wireless LAN connection, the optional USB Wireless LAN Unit is required. (→ page 115) To use wired/wireless LAN connection, connect the projector to the computer with a commercially available LAN cable. (→ page 114) 2.
3.
3. Convenient Features PICTURE: Controls the video adjustment of the projector. CONTRAST �������� Increases the contrast adjustment value. CONTRAST �������� Decreases the contrast adjustment value. BRIGHTNESS ���� Increases the brightness adjustment value. BRIGHTNESS ���� Decreases the brightness adjustment value. SHARPNESS ����� Increases the sharpness adjustment value. SHARPNESS ����� Decreases the sharpness adjustment value. COLOR �������������� Increases the color adjustment value.
3. Convenient Features NETWORK SETTINGS • SETTINGS WIRED or WIRELESS SETTING Set for wired LAN or for wireless LAN. APPLY Apply your settings to wired LAN or wireless LAN. DHCP ON Automatically assign IP address, subnet mask, and gateway to the projector from your DHCP server. DHCP OFF Set IP address, subnet mask, and gateway to the projector assigned by your network administrator. IP ADDRESS Set your IP address of the network connected to the projector.
3. Convenient Features SITE SURVEY Displays a list of available SSIDs for wireless LAN on site. Select an SSID which you can access. SECURITY TYPE Turn on or off the encryption mode for secure transmission. When turn on the encryption mode, set WEP key or encrypted key. DISABLE Will not turn on the encryption feature. Your communications may be monitored by someone. WEP 64 bit Uses 64-bit datalength for secure transmission. WEP 128 bit Uses 128-bit datalength for secure transmission.
3. Convenient Features • ALERT MAIL ALERT MAIL (English only) This option will notify your computer of lamp replace time or error messages via e-mail when using wireless or wired LAN. Placing a checkmark will turn on the Alert Mail feature. Clearing a checkmark will turn off the Alert Mail feature. Sample of a message to be sent from the projector: The lamp and filters are at the end of its usable life. Please replace the lamp and filters.
3. Convenient Features • ROOMVIEW for managing from the computer. DISABLE Disables ROOMVIEW. ENABLE Enables ROOMVIEW. • CRESTRON CONTROL for managing from the controller. DISABLE Disables CRESTRON CONTROL. ENABLE Enables CRESTRON CONTROL. IP ADDRESS Set your IP address of CRESTRON SERVER. IP ID Set your IP ID of CRESTRON SERVER. TIP: The CRESTRON settings are required only for use with CRESTRON ROOMVIEW. For more information, visit http://www.crestron.
3. Convenient Features Controlling the Projector over a LAN (PC Control Utility Pro 4/ Pro 5) Using the utility software “PC Control Utility Pro 4” and “PC Control Utility Pro 5” included on the companion NEC Projector CD-ROM, the projector can be controlled from a computer over a LAN. PC Control Utility Pro 4 is a program compatible with Windows. (→ this page) PC Control Utility Pro 5 is a program compatible with Mac OS.
3. Convenient Features TIP: If the menu window will not be displayed, try the following procedure. For Windows 7: 1. Click “start” on Windows. 2. Click “All Programs” → “Accessories” → “Run”. 3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\ LAUNCHER.EXE) 4. Click “OK”. The menu window will be displayed. 2 Click “PC Control Utility Pro 4” on the menu window. The installation will start.
3. Convenient Features Step 2: Connect the projector to a LAN. Connect the projector to the LAN by following the instructions in “Connecting to a Wired LAN” (→ page 114), “Connecting to a Wireless LAN (Optional: NP05LM series)” (→ page 115) and “ Controlling the Projector by Using an HTTP Browser” (→ page 45) Step 3: Start PC Control Utility Pro 4 Click “Start” → “All programs” or “Programs” → “NEC Projector User Supportware” → “PC Control Utility Pro 4” → “PC Control Utility Pro 4”.
3. Convenient Features Using on Mac OS Step 1: Install PC Control Utility Pro 5 on the computer 1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive. The CD-ROM icon will be displayed on the desktop. 2. Double-click the CD-ROM icon. The CD-ROM window will be displayed. 3. Double-click the “Mac OS X” folder. 4. Double-click “PC Control Utility Pro 5.pkg”. The installer will start. 5. Click “Next”. “END USER LICENSE AGREEMENT” screen will be displayed. 6.
3. Convenient Features Projecting Your Computer’s Screen Image from the Projector over a LAN (Image Express Utility Lite) Using Image Express Utility Lite contained on the supplied NEC Projector CD-ROM allows you to send the computer’s screen image to the projector over a USB cable or a wired or wireless LAN. Image Express Utility Lite is a program compatible with Windows. Image Express Utility Lite for Mac OS is a program compatible with Mac OS.
3. Convenient Features TIP: If the menu window will not be displayed, try the following procedure. For Windows 7: 1. Click “start” on Windows. 2. Click “All Programs” → “Accessories” → “Run”. 3. Type your CD-ROM drive name (example: “Q:\”) and “LAUNCHER.EXE” in “Name”. (example: Q:\LAUNCHER.EXE) 4. Click “OK”. The menu window will be displayed. 2. Click “Installing Image Express Utility Lite” on the menu window. The installation will start. “END USER LICENSE AGREEMENT” screen will be displayed.
3. Convenient Features 3. Place a check mark for projectors to be connected, and then click “Connect”. • When one or more projectors are displayed, from the menu on the projector, select [INFO.] → [WIRELESS LAN] → [IP ADDRESS]. When connecting with the projector is established, you can operate the control window to control the projector.
3. Convenient Features Starting Image Express Utility Lite from a USB Memory or SD Card Image Express Utility Lite can be started from commercially available removable media such USB memory or SD cards if it is copied beforehand. This will eliminate the trouble of installing Image Express Utility Lite to your computer. 1. Copy Image Express Utility Lite to removable media. Copy all the folders and files (total size approx.
3. Convenient Features Using on Mac OS Step 1: Install Image Express Utility Lite for Mac OS on the computer 1. Insert the accompanying NEC Projector CD-ROM in your Mac CD-ROM drive. The CD-ROM icon will be displayed on the desktop. 2. Double-click the CD-ROM icon. The CD-ROM window will be displayed. 3. Double-click the “Mac OS X” folder. 4. Double-click “Image Express Utility Lite.dmg”. The “Image Express Utility Lite” window will be displayed. 5.
3. Convenient Features Projecting an Image from an Angle (Geometric Correction Tool in Image Express Utility Lite) The Geometric Correction Tool (GCT) function allows you to correct distortion of images projected even from an angle. What you can do with GCT • The GCT feature includes the following three functions • 4-point Correction: You can fit a projected image within the border of the screen easily by align the four corners of an image to the ones of the screen.
3. Convenient Features 3. Use the mouse to click the [ • ] mark of which corner you wish to move. The currently selected [ • ] mark will turn red. (In the above example, Windows screens are omitted for clarification.) 4. Drag the selected [ • ] mark to the point you wish to correct and drop it. • When you click somewhere within the project image area, the nearest [ • ] mark will go to the position where the mouse cursor is. 5. Repeat Step 3 and 4 to correct the distortion of the projected image.
3. Convenient Features Connecting Your Microphone Connecting a commercially available dynamic microphone or condenser mic to the MIC input jack allows you to output your mic sound from the built-in speaker. Sound input from all input terminals including LAN, USB-A, and USB-B will be heard from the speaker with your microphone voice. Microphone sensitivity can be adjusted. From the menu, select [SETUP] → [INSTALLATION] → [MIC GAIN].
4. Using the Viewer ❶ What you can do with the Viewer The Viewer has the following features. • When a commercially available USB memory that stores image files is inserted into the USB port (Type A) of the projector, the Viewer allows you to view the image files on the USB memory. Even if no computer is available, presentations can be conducted simply with the projector. • Supported graphic format is JPEG.
4. Using the Viewer NOTE • The USB port of the projector does not support USB hub. • The following operations by using the buttons on the projector are not possible when the VIEWER screen such as the slide screen and the thumbnail screen is displayed. Buttons on the cabinet - Keystone correction by using the ▲/▼ button - Auto Adjustment by using the AUTO ADJ.
4. Using the Viewer ❷ Projecting images stored in a USB memory device This section explains the basic operation of the Viewer. The explanation provides the operational procedure when the Viewer toolbar (→ page 69) is set to the factory default. - Starting the Viewer........................................................................below - Removing the USB memory from the projector........................ page 68 - Exiting the Viewer.....................................................................
4. Using the Viewer 4. Press the ENTER button. The thumbnail screen will be displayed. (→ page 70) 5. Use the ▲▼◀ or ▶ button to select an icon. • The → (arrow) symbol on the right indicates there are more pages. pressing the PAGE ▽ (page down) button will show the next page: pressing the PAGE △ (page up) will show the previous page. 6. Press the ENTER button. The selected slide will be displayed. • When a folder icon is selected, icons contained in the folder will be displayed. 7.
4. Using the Viewer Removing the USB memory from the projector 1. Select the VIEWER start screen. Press the EXIT button with no menu displayed. 2. Remove the USB memory from the projector. Make sure that the LED on the USB memory is not flashing before removing the USB memory. NOTE: If you remove the USB memory from the projector with a slide displayed, the projector may not operate correctly. If this happens, turn off the projector and unplug the power cord.
4. Using the Viewer Parts of each screen The Viewer has four screens. (1) Viewer start screen (5) (2) (3) Thumbnail screen (6) (4) (7) (9) Slide screen/ (11) Slideshow screen (8) (10) (12) Name Description (1) Viewer start screen This screen will be displayed first when you select the Viewer. (2) USB icon This icon indicates that the USB memory is inserted into the projector. (3) Thumbnail screen This screen will show a list of folders and image files stored in the USB memory.
4. Using the Viewer Using the toolbar 1. Press the MENU button. The toolbar will be displayed. The SOURCE screen will be displayed as Viewer connection screen. 2. Use the ◀ or ▶ button to select an item and use the ▲ or ▼ button to select its available option. When the cursor is placed, the selected item will be changed to yellow. The ▲ or ▼ shows more available choices. 3. Press the ENTER button. The selected item will be displayed. 4. Press the MENU button two times.
4. Using the Viewer Slide toolbar (1) Menu Options (1) Display (2) (3) (4) Description Closes the menu and switches to the slide screen. Closes the menu and displays the thumbnail screen. Closes the menu and starts the slideshow from the highlighted item. (2) Image display Closes the menu and displays the image in its actual size. Closes the menu and displays the image in the projector’s maximum resolution.
5. Using On-Screen Menu Using the Menus NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected. 1. Press the MENU button on the remote control or the projector cabinet to display the menu. NOTE: The commands such as ENTER, EXIT, , in the bottom show available buttons for your operation. 2. Press the buttons on the remote control or the projector cabinet to display the submenu. 3.
5. Using On-Screen Menu 2 Menu Elements Tab Slide bar Solid triangle Available buttons Source Highlight Radio button Wireless symbol ECO mode symbol High Altitude symbol Off Timer remaining time Thermometer symbol Key Lock symbol Menu windows or dialog boxes typically have the following elements: Highlight �����������������������������Indicates the selected menu or item. Solid triangle ����������������������Indicates further choices are available.
5. Using On-Screen Menu 3 List of Menu Items Some menu items are not available depending on the input source.
5.
5. Using On-Screen Menu Menu Item Default Options LAMP LIFE REMAINING LAMP HOURS USED USAGE TIME FILTER HOURS USED TOTAL CARBON SAVINGS TOTAL COST SAVINGS SOURCE NAME SOURCE INDEX HORIZONTAL FREQUENCY SOURCE(1) SOURCE(2) INFO. WIRED LAN VERTICAL FREQUENCY SYNC TYPE SYNC POLARITY SCAN TYPE SIGNAL TYPE VIDEO TYPE BIT DEPTH VIDEO LEVEL MHL SIGNAL IP ADDRESS SEPARATE SYNC, COMPOSITE SYNC, SYNC ON GREEN, SYNC ON VIDEO INTERLACE, NON-INTERLACE RGB, COMPONENT, VIDEO, HDTV NTSC, NTSC3.58, NTSC4.
5. Using On-Screen Menu 4 Menu Descriptions & Functions [SOURCE] COMPUTER Selects the computer connected to your COMPUTER input terminal signal. NOTE: When the component input signal is connected to the COMPUTER IN terminal, select [COMPUTER]. HDMI1/MHL and HDMI2 Selects the HDMI compatible equipment connected to your HDMI1/MHL or 2 IN terminal. VIDEO Selects what is connected to your VIDEO input-VCR, DVD player or document camera.
5. Using On-Screen Menu 5 Menu Descriptions & Functions [ADJUST] [PICTURE] [PRESET] This function allows you to select optimized settings for your projected image. You can adjust neutral tint for yellow, cyan or magenta. There are seven factory presets optimized for various types of images. You can also use [DETAIL SETTINGS] to set user adjustable settings to customize each gamma or color. Your settings can be stored in [PRESET 1] to [PRESET 7].
5. Using On-Screen Menu [GENERAL] Storing Your Customized Settings [REFERENCE] This function allows you to store your customized settings in [PRESET 1] to [PRESET 7]. First, select a base preset mode from [REFERENCE], then set [GAMMA CORRECTION] and [COLOR TEMPERATURE]. HIGH-BRIGHT �������� Recommended for use in a brightly lit room. PRESENTATION ����� Recommended for making a presentation using a PowerPoint file. VIDEO �������������������� Recommended for typical TV program viewing.
5. Using On-Screen Menu Enhancing the Color [COLOR ENHANCEMENT] This allows you to adjust the color density of the image. The color of the image will become deeper in the order of "LOW", "MEDIUM", AND "HIGH" as the displayed image will become darker. With "OFF" selected, the COLOR ENHANCEMENT function will not work. NOTE: This function is available only when [PRESENTATION] is selected [REFERENCE]. Adjusting White Balance [WHITE BALANCE] This allows you to adjust the white balance.
5. Using On-Screen Menu [IMAGE OPTIONS] Adjusting Clock and Phase [CLOCK/PHASE] This allows you to manually adjust CLOCK and PHASE. CLOCK ������������������� Use this item to fine tune the computer image or to remove any vertical banding that might appear. This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This adjustment may be necessary when you connect your computer for the first time.
5. Using On-Screen Menu Adjusting Horizontal/Vertical Position [HORIZONTAL/VERTICAL] Adjusts the image location horizontally and vertically. - An image can be distorted during the adjustment of [CLOCK] and [PHASE]. This is not malfunction. - The adjustments for [CLOCK], [PHASE], [HORIZONTAL], and [VERTICAL] will be stored in memory for the current signal. The next time you project the signal with the same resolution, horizontal and vertical frequency, its adjustments will be called up and applied.
5. Using On-Screen Menu Selecting Aspect Ratio [ASPECT RATIO] The term “aspect ratio” refers to the ratio of width to height of a projected image. The projector automatically determines the incoming signal and displays it in its appropriate aspect ratio. • This table shows typical resolutions and aspect ratios that most computers support.
5. Using On-Screen Menu Sample image when the appropriate aspect ratio is automatically determined UM361X/UM301X [Computer signal] Aspect ratio of incoming signal 4:3 5:4 4:3 Letterbox 16:9 15:9 16:10 Sample image when the appropriate aspect ratio is automatically determined [Video signal] Aspect ratio of incoming signal Sample image when the aspect ratio is automatically determined Squeeze NOTE: To display a squeezed signal properly, select [16:9] or [WIDE ZOOM].
5. Using On-Screen Menu [AUDIO] Turning Up or Down Sound Adjusts the volume of the projector speaker and AUDIO OUT (Stereo Mini Jack). TIP: • When no menus appear, the ◀ and ▶ buttons on the projector cabinet and the VOL. +/− buttons on the remote control work as a volume control.
5. Using On-Screen Menu 6 Menu Descriptions & Functions [SETUP] [GENERAL] Using Digital Zoom [DIGITAL ZOOM] This feature allows you to electronically fine adjust the image size on the screen. NOTE: • This feature can not be used when USB-A, LAN, or USB-B is selected as a input terminal. TIP: To adjust the projected image size roughly, move the projector away or closer to the screen. To fine adjust the zoom, use the [DIGITAL ZOOM] function.
5. Using On-Screen Menu Using the Wall Color Correction [WALL COLOR] This function allows for quick adaptive color correction in applications where the screen material is not white. NOTE: Selecting [WHITEBOARD] reduces lamp brightness. Setting Eco Mode [ECO MODE] The ECO MODE increases lamp life, while lowering power consumption and cutting down on CO2 emissions. Four brightness modes of the lamp can be selected: [OFF], [AUTO ECO], [NORMAL] and [ECO] modes.
5. Using On-Screen Menu Setting Closed Caption [CLOSED CAPTION] This option sets several closed caption modes that allow text to be superimposed on the projected image of Video or S-Video. OFF ������������������������ This exits the closed caption mode. CAPTION 1-4 ��������� Text is superimposed. TEXT 1-4 ���������������� Text is displayed. NOTE: • The closed caption is not available under the following conditions: - when messages or menus are displayed. - when an image is magnified, frozen, or muted.
5. Using On-Screen Menu Turning ON/OFF Control ID [ID DISPLAY] ID DISPLAY ����������� This option turns on or off the ID number which is displayed when the ID SET button on the remote control is pressed. Turning On / Off Eco Message [ECO MESSAGE] This option turns on or off the following messages when the projector is turned on. The Eco Message prompts the user to save energy.
5. Using On-Screen Menu [INSTALLATION] Selecting Projector Orientation [ORIENTATION] This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection.
5. Using On-Screen Menu Selecting Communication Speed [COMMUNICATION SPEED] This feature sets the baud rate of the PC Control port (D-Sub 9P). It supports data rates from 4800 to 38400 bps. The default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud rate may be recommended for long cable runs). NOTE: Your selected communication speed will not be affected even when [RESET] is done from the menu.
5. Using On-Screen Menu Using Test Pattern [TEST PATTERN] Displays the test pattern to check for image distortion at the time of the projector setup. Press the ENTER button to display the test pattern; press the EXIT button to close the test pattern and return to the menu. Menu operation and corrections for keystone, cornerstone and pincushion are not available when the test pattern is displayed.
5. Using On-Screen Menu lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO]. • Using the projector at altitudes approximately 5500 feet/1700 meters or higher can shorten the life of optical components such as the lamp. • Your setting will not be affected even when [RESET] is done from the menu. TIP: • When [HIGH ALTITUDE] is selected, an icon [ ] is displayed at the bottom of the on-screen menu.
5. Using On-Screen Menu USB-B �������������������� Select [USB-B] or [COMPUTER] to switch the source connected over the USB cable (USB-B). Enabling Key Sound and Error Sound [BEEP] This feature turns on or off the button sound or alarm when an error occurs or the following operations are performed.
5. Using On-Screen Menu Turning On the Projector By Applying Computer Signal [AUTO POWER ON] When the projector is in Standby mode, applying a computer or HDMI signal from a computer connected to the COMPUTER IN input, HDMI1/MHL, or HDMI2 input will power on the projector and simultaneously project the image. This functionality eliminates the need to always use the POWER button on the remote control or the projector cabinet to power on the projector.
5. Using On-Screen Menu Setting up the Projector for a Wired LAN Connection [WIRED LAN] Important • Consult with your network administrator about these settings. • When using a wired LAN connection, connect a LAN cable (Ethernet cable) to the LAN port (RJ-45) of the projector. (→ page 114) TIP: The network settings you make will not be affected even when [RESET] is done from the menu. [WIRED LAN] [SETTINGS] [DISABLE] Wired LAN connection will be turned off.
5. Using On-Screen Menu Setting up the Projector for a Wireless LAN Connection (with the optional USB Wireless LAN Unit equipped) [WIRLESS LAN] Important • Consult with your network administrator about these settings. • When using a wireless LAN connection, attach the optional USB Wireless LAN to the projector. (→ page 115) [PROFILE] [DISABLE] Wireless LAN connection will be turned off [SIMPLE ACCESS POINT] Set the projector for simple access point.
5. Using On-Screen Menu Hints on How to Set Up LAN Connection To set up the projector for a LAN connection: Access the HTTP server function to display the web browser (→ page 45) and select [NETWORK SETTINGS] → [SETTINGS] → [WIRELESS LAN] → [PROFILE 1] or [PROFILE 2]. Two settings can be set for the USB Wireless LAN Unit. Next select [SETTINGS] for your selected profile, and set [ENABLE] or [DISABLE] for [DHCP], [IP ADDRESS], [SUBNET MASK], and [GATEWAY]. Last click [SAVE].
5. Using On-Screen Menu 7 Menu Descriptions & Functions [INFO.] Displays the status of the current signal and lamp usage. This item has six pages. The information included is as follows: TIP: Pressing the HELP button on the remote control will show the [INFO.] menu items. [USAGE TIME] [LAMP LIFE REMAINING] (%)* [LAMP HOURS USED] (H) [FILTER HOURS USED] (H) [TOTAL CARBON SAVINGS] (kg-CO2) [TOTAL COST SAVINGS] * The progress indicator shows the percentage of remaining bulb life.
5.
5. Using On-Screen Menu [WIRELESS LAN] [IP ADDRESS] [GATEWAY] [SSID] [WEP/WPA] [SIGNAL LEVEL] [SUBNET MASK] [MAC ADDRESS] [NETWORK TYPE] [CHANNEL] [VERSION] [FIRMWARE] Version [DATA] Version [OTHERS] [PROJECTOR NAME] [MODEL NO.
5. Using On-Screen Menu 8 Menu Descriptions & Functions [RESET] Returning to Factory Default [RESET] The RESET feature allows you to change adjustments and settings to the factory preset for a (all) source (s) except the following: [CURRENT SIGNAL] Resets the adjustments for the current signal to the factory preset levels. The items that can be reset are: [PRESET], [CONTRAST], [BRIGHTNESS], [COLOR], [HUE], [SHARPNESS], [ASPECT RATIO], [HORIZONTAL], [VERTICAL], [CLOCK], [PHASE], and [OVERSCAN].
6. Installation and Connections Setting Up the Screen and the Projector [UM361X/UM301X] The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is 61.5" (1562 mm) measured diagonally when the projector is 4 inches (105 mm) between the screen side of the projector and the wall or screen. The largest the image can be is 116.6" (2962 mm) when the projector is 20 inches (510 mm) between the screen side of the projector and the wall or screen.
6. Installation and Connections [UM351W/UM301W] The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is 58" (1473 mm) measured diagonally when the projector is 4 inches (105 mm) between the screen side of the projector and the wall or screen. The largest the image can be is 110" (2794 mm) when the projector is 20 inches (510 mm) between the screen side of the projector and the wall or screen.
6. Installation and Connections WARNING Reflecting the Image * Installing your projector on the ceiling must be done by a qualified technician. Contact your NEC dealer for more information. * Do not attempt to install the projector yourself. • Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector severely damaged. • Do not use the projector where temperatures vary greatly.
6. Installation and Connections Making Connections Connecting Your Computer Computer cables, HDMI and USB can be used to connect to a computer. The connection cable is not enclosed with the projector. Please get ready a suitable cable for the connection. NOTE: Signals supported by Plug & Play (DDC2) COMPUTER IN analog Yes INPUT HDMI 1/MHL IN digital Yes HDMI 2 IN digital Yes HDMI cable (not supplied) Use High Speed HDMI® Cable.
6. Installation and Connections NOTE: The projector is not compatible with video decoded outputs of the NEC ISS-6020 switcher. NOTE: An image may not be displayed correctly when a Video source is played back via a commercially available scan converter. This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
6. Installation and Connections Connecting an External Monitor Stereo mini-plug audio cable (not supplied) Computer cable (VGA) (not supplied) Computer cable (VGA) (supplied) Stereo mini-plug audio cable (not supplied) You can connect a separate, external monitor to your projector to simultaneously view on a monitor the computer analog image you’re projecting. NOTE: • When audio equipment is connected, the projector speaker is disabled.
6. Installation and Connections Connecting Your DVD Player or Other AV Equipment Connecting Video Input Audio cable (not supplied) Video cable (not supplied) Audio equipment Audio cable (not supplied) • Select the source name for its appropriate input terminal after turning on the projector.
6. Installation and Connections Connecting Component Input 15-pin - to - RCA (female) × 3 cable adapter (ADP-CV1E) Stereo mini plug - to - RCA audio cable (not supplied) Audio Equipment Component video RCA × 3 cable (not supplied) DVD player Audio cable (not supplied) A component signal will be automatically displayed. If not, from the menu, select [SETUP] → [OPTIONS(1)] → [SIGNAL SELECT] → [COMPUTER], and then place a check mark in the Component radio button.
6. Installation and Connections Connecting HDMI Input You can connect the HDMI output of your DVD player, hard disk player, Blu-ray player, or notebook type PC to the HDMI IN terminal of your projector. HDMI cable (not supplied) Use High Speed HDMI® Cable. Audio cable (not supplied) • Select the source name for its appropriate input terminal after turning on the projector.
6. Installation and Connections Connecting a smart phone and a tablet terminal The below mentioned feature is available when the projector is connected with MHL supported devices such as a smart phone and a tablet terminal by a MHL cable (not supplied) • Projecting a image and a file on the MHL supported devices. • Output sound on the MHL supported devices from the build-in speaker. • Charge the MHL supported devices. • Operate the MHL supported devices by the remote control for the projector.
6. Installation and Connections Connecting your document camera You can connect your document camera and project printed documents, etc. Name, position, and direction of terminals are vary depending on camera model. Please check user's manual of your camera for details. Computer cable (VGA) (supplied) Video cable (not supplied) • Select the source name for its appropriate input terminal after turning on the projector.
6. Installation and Connections Connecting to a Wired LAN The projector comes standard with a LAN port (RJ-45) which provides a LAN connection using a LAN cable. To use a LAN connection, you are required to set the LAN on the projector menu. Select [SETUP] → [WIRED LAN]. (→ page 96). Example of LAN connection Example of wired LAN connection Server Hub LAN cable (not supplied) NOTE: Use a Category 5 or higher LAN cable.
6. Installation and Connections Connecting to a Wireless LAN (Optional: NP05LM series) The USB Wireless LAN Unit also provides a wireless LAN connection. To use a wireless LAN connection, you are required to assign an IP address to the projector. Important: • If you use the projector with the USB Wireless LAN Unit in the area where the use of wireless LAN equipment is prohibited, remove the USB Wireless LAN Unit from the projector. • Buy the appropriate USB Wireless LAN Unit for your country or area.
6. Installation and Connections NOTE:When the cable cover is attached, remove it before inserting the USB Wireless LAN Unit. 1. Press the POWER button to turn off the projector and set it into standby condition, and disconnect the power cord. 2. Slowly insert the USB Wireless LAN Unit into the USB (WLAN) port. Remove the cap from the USB Wireless LAN Unit, and then insert it with the surface (side of indicator) facing outward. Keep the cap for later use.
6.
7. Maintenance This section describes the simple maintenance procedures you should follow to clean the filters, the projection window, the cabinet, and to replace the lamp and the filters. Cleaning the Filters The air-filter sponge keeps dust and dirt from getting inside the projector and should be frequently cleaned. If the filter is dirty or clogged, your projector may overheat. WARNING • Do not use a spray containing flammable gas to get rid of accumulated dust and dirt on the filters.
7. Maintenance 3. Remove the four filters and use a vacuum cleaner to vacuum all the dust inside and outside. Get rid of dust in the sponge filter NOTE: • Whenever you vacuum the filter, use the soft brush attachment to vacuum. This is to avoid damage to the filter. • Do not wash the filter with water. Doing so can result in filter clogging. 4. Remove dust from the filter cover and the two filter cases (large and small). Clean both outside and inside. 5.
7. Maintenance 6. Insert the large filter case into the projector cabinet. Make sure that the filter case is inserted in the correct orientation. 7. Put the small filter case to the projector cabinet. Make sure that the filter case is inserted in the correct orientation. 8. Put the filter cover back to the projector cabinet. Insert two catches of the tip of the filter cover into the groove of the cabinet, and push the button to close the filter cover.
7. Maintenance 2 Cleaning the Projection Window • Turn off the projector before cleaning. • Do not scratch or mar the projection window as it is made of glass. • Use a blower or lens paper to clean the projection window, and be careful not to scratch or mar the glass surface. WARNING • Do not use a spray containing flammable gas to get rid of accumulated dust and dirt on the projection window. It may cause of fire.
7. Maintenance 4 Replacing the Lamp and the Filters When the lamp reaches the end of its life, the LAMP indicator in the cabinet will blink red and the message “THE LAMP HAS REACHED THE END OF ITS USABLE LIFE. PLEASE REPLACE THE LAMP AND FILTER.” will appear (*). Even though the lamp may still be working, replace the lamp to maintain the optimal projector performance. After replacing the lamp, be sure to clear the lamp hour meter.
7. Maintenance To replace the lamp: 1. Remove the lamp cover. (1) Loosen the lamp cover screw • The lamp cover screw is not removable. (2) Push and slide the lamp cover off. a b 2. Remove the lamp housing. (1) Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condition. • The two screws are not removable. • There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.
7. Maintenance 3. Install a new lamp housing. (1) Insert a new lamp housing until the lamp housing is plugged into the socket. (2) Push the top center of the lamp housing to secure it. (3) Secure it in place with the two screws. • Be sure to tighten the screws. 4. Reattach the lamp cover. (1) Slide the lamp cover back until it snaps into place. (2) Tighten the screw to secure the lamp cover. • Be sure to tighten the screw. a b This completes the lamp replacement. Go on to the filter replacement.
7. Maintenance To replace the filters: NOTE: • Replace all four filters at the same time. • Before replacing the filters, wipe off dust and dirt from the projector cabinet. • The projector is precision equipment. Keep out dust and dirt during filter replacement. • Do not wash the filters with soap and water. Soap and water will damage the filter membrane. • Put filters into place. Incorrect attachment of a filter may cause dust and dirt to get into the inside of the projector.
7. Maintenance 3. Remove the four filters and use a vacuum cleaner to vacuum all the dust inside and outside. Get rid of dust in the sponge filter NOTE: • Whenever you vacuum the filter, use the soft brush attachment to vacuum. This is to avoid damage to the filter. • Do not wash the filter with water. Doing so can result in filter clogging. 4. Remove dust from the filter cover and the two filter cases (large and small). Clean both outside and inside. 5.
7. Maintenance 6. Insert the large filter case into the projector cabinet. Make sure that the filter case is inserted in the correct orientation. 7. Put the small filter case to the projector cabinet. Make sure that the filter case is inserted in the correct orientation. 8. Put the filter cover back to the projector cabinet. Insert two catches of the tip of the filter cover into the groove of the cabinet, and push the button to close the filter cover.
8. Appendix Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. Indicator Messages Power Indicator Indicator Condition Off 0.5 sec On, Blinking light Blue 0.5 sec Off 2.5 sec On, 0.5 sec Off Orange Steady light Blue Orange Red Projector Condition The main power is off The projector is getting ready to turn on. – Wait for a moment. Note Off Timer is enabled. – Cooling The projector is turned on.
8. Appendix Common Problems & Solutions (→ “Power/Status/Lamp Indicator” on page 128.) Problem Check These Items Does not turn on or shut down • Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control is on. (→ pages 13, 14) • Ensure that the lamp cover is installed correctly. (→ page 124) • Check to see if the projector has overheated.
8. Appendix Problem Check These Items Mic sound is not heard • Check if your microphone cable is connected to the MIC input jack correctly. • Check if selection of microphone type in the installation menu is correct. Mic sound is too loud or quiet • Adjust [MIC GAIN] from the menu. (→ page 92) For more information contact your dealer. If there is no picture, or the picture is not displayed correctly. • Power on process for the projector and the PC.
8. Appendix Specifications This section provides technical information about projector’s performance. Optical Model Number LCD Panel Resolution*1 Lens Lamp Light Output*2*3 Contrast Ratio*3 (full white: full black) Image Size (Diagonal) Projection Distance (Min.–Max.) Projection Angle NP-UM361X NP-UM301X 0.63 inch LCD with Micro Lens Array (Aspect Ratio 4:3) 1024 × 768 pixels (XGA) Digital zoom and manual focus Digital Zoom Ratio = 1.4 F = 1.8 f = 4.
8. Appendix Model Number Built-in Speaker Power Requirement Input Current Power Con- ECO MODE OFF sumption NORMAL ECO NP-UM361X NP-UM301X 20 W (monaural) 100–240V AC, 50/60Hz 3.8A/1.6A 3.5A/1.5A 337 W (100-130 V) 297 W (100-130 V) 324 W (200-240 V) 285 W (200-240 V) 265 W (100-130 V) 234 W (100-130 V) 257 W (200-240 V) 227 W (200-240 V) 221 W (100-130 V) 196 W (100-130 V) 214 W (200-240 V) 190 W (200-240 V) 2.1W (100-130 V)/2.4W (200-240 V) NP-UM351W NP-UM301W 3.8A/1.
8. Appendix Cabinet Dimensions Unit: mm (inch) 428 (16.9) 424.5 (16.7) 344 (13.5) 112 (4.4) 114 (4.5) 160 (6.3) 5.5 (0.2) 378 (14.9) 114 (4.5) Attachment surface of ceiling mount 43 (1.7) 115 (4.5) 112.5 (4.4) 151.25 163 (6.
8. Appendix 4 Pin Assignments of D-Sub COMPUTER Input Terminal Mini D-Sub 15 Pin Terminal 11 12 13 14 15 6 7 8 9 10 1 2 3 4 5 Signal Level Video signal : 0.7Vp-p (Analog) Sync signal : TTL level Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 RGB Signal (Analog) Red Green or Sync on Green Blue Ground Ground Red Ground Green Ground Blue Ground Hotplug Sync Signal Ground No Connection Bi-directional DATA (SDA) Horizontal Sync or Composite Sync Vertical Sync Data Clock COMPUTER IN NOTE: Pin Nos.
8.
8.
8. Appendix 7 Troubleshooting Check List Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem more efficiently. * Print this page and the next page for your check.
8. Appendix In the space below please describe your problem in detail. Information on application and environment where your projector is used Projector Installation environment Model number: Screen size: Serial No.
8. Appendix 8 TCO Certification Some models in this product family are TCO certified. All TCO certified models have the TCO mark on the marking plate (on the bottom of the product). To see a list of our TCO certified projectors and their TCO Certification (in English only), visit our website at http://www.nec-display.com/ap/en_projector/tco/index.html The TCO certification, designed by TCO Development, is an international environmental and ergonomics standard for IT equipment.
8. Appendix 9 REGISTER YOUR PROJECTOR! (for residents in the United States, Canada, and Mexico) Please take time to register your new projector. This will activate your limited parts and labor warranty and InstaCare service program. Visit our web site at www.necdisplay.com, click on support center/register product and submit your completed form online.
© NEC Display Solutions, Ltd.
