Electronics America Single-Chip Microcontrollers User's Manual

CHAPTER 22 ELECTRICAL SPECIFICATIONS ( µ PD789488, 78F9488, 789489, 78F9489)
User’s Manual U15331EJ4V1UD 349
DC Characteristics (TA = –40 to +85°C, VDD = 1.8 to 5.5 V) (4/6)
Parameter Symbol Conditions MIN. TYP. MAX. Unit
VDD = 5.0 V ±10%
Note 2
5.5 9.0 mA
VDD = 3.0 V ±10%
Note 3
1.3 2.3 mA
IDD1 5.0 MHz crystal oscillation
operation mode
(C1 = C2 = 22 pF)
V
DD = 2.0 V ±10%
Note 3
0.8 1.6 mA
VDD = 5.0 V ±10%
Note 2
1.5 2.1 mA
VDD = 3.0 V ±10%
Note 3
0.41 0.85 mA
IDD2 5.0 MHz crystal oscillation
HALT mode
Note 4
(C1 = C2 = 22 pF)
V
DD = 2.0 V ±10%
Note 3
0.2 0.43 mA
VDD = 5.0 V ±10% 115 200 µ A
VDD = 3.0 V ±10% 85 140 µ A
32.768 kHz crystal
oscillation operation
mode
Note 5
(C3 = C4 = 22 pF, R1 =
220kΩ)
V
DD = 2.0 V ±10% 70 110 µ A
VDD = 5.0 V ±10% 315 480 µ A
IDD3
32.768 kHz crystal
oscillation operation × 4
multiplication operation
mode
Note 5
(C3 = C4 = 22 pF, R1 =
220kΩ)
V
DD = 3.0 V ±10% 200 300 µ A
VDD = 5.0 V ±10% 25 65 µ A
VDD = 3.0 V ±10% 8 29 µ A
LCD not
operating
Note 4
V
DD = 2.0 V ±10% 5 20 µ A
VDD = 5.0 V ±10% 28 70 µ A
VDD = 3.0 V ±10% 10 34 µ A
32.768 kHz
crystal
oscillation
HALT
mode
Note 5
(C3 = C4 =
22 pF, R1 =
220kΩ)
LCD
operating
Note 7
V
DD = 2.0 V ±10% 7 25 µ A
VDD = 5.0 V ±10% 25 65 µ A LCD not
operating
Note 4
V
DD = 3.0 V ±10% 8 29 µ A
VDD = 5.0 V ±10% 28 70 µ A
IDD4
32.768 kHz
crystal
oscillation × 4
multiplication
HALT
mode
Note 5
(C3 = C4 =
22 pF, R1 =
220kΩ)
LCD
operating
Note 7
V
DD = 3.0 V ±10% 10 34 µ A
VDD = 5.0 V ±10% 0.1 10 µ A
VDD = 3.0 V ±10% 0.05 5 µ A
IDD5 STOP mode
Note 6
V
DD = 2.0 V ±10% 0.05 3 µ A
VDD = 5.0 V ±10%
Note 2
6.5 10.2 mA
VDD = 3.0 V ±10%
Note 3
2.0 3.3 mA
Power supply
current
Note 1
( µ PD78F9488)
I
DD6 5.0 MHz crystal oscillation
A/D operating mode
Note 8
(C1 = C2 = 22 pF)
V
DD = 2.0 V ±10%
Note 3
1.3 2.6 mA
Notes 1. The port current (including the current that flows to on-chip pull-up resistors) is not included.
2. High-speed mode operation (when the processor clock control register (PCC) is set to 00H)
3. Low-speed mode operation (when PCC is set to 02H)
4. When the LCD is not operating and the booster circuit is operating (LCDON0 = 0, VAON0 = 1, LIPS0 = 1).
5. When the main system clock is stopped
6. When the LCD is not operating (LCDON0 = 0, VAON0 = 0, LIPS0 = 0)
7. Then the LCD is operating (LCDON0 = 1, VAON0 = 1, LIPS0 = 1)
8. This is the total current that flows to V
DD and AVDD.
Remark Unless otherwise specified, the characteristics of alternate-function pins are the same as those of port
pins.