PlasmaSync 3300 Multimedia Monitor NEC Technologies, Inc. MultiSync is a registered trademark of NEC Technologies, Inc. in the U.S.A. NEC is registered trademark of NEC Corporation. 1993 by NEC Technologies, Inc. 1250 N.
DOC compliance Notice CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.
ATTENTION RISQUE D’ELECTROCUTION NE PAS OUVRIR MISE EN GARDE: DOC avis de conformation Cet appareil numérigue de la classe A respecte toutes les exigences du Réglement sur le Matériel Brouilleur du Canada. AFIN DE REDUIRE LES RISQUES D’ELECTROCUTION, NE PAS DEPOSER LE COUVERCLE, IL N’Y A AUCUNE PIECE UTILISABLE A L’INTERIEUR DE CET APPAREIL. NE CONFIER LES TRAVAUX D’ENTRETIEN QU’A UN PERSONNEL QUALIFIE.
CONTENTS Introduction ......................................................................................................................... 1 Introduction to the PlasmaSync 3300 ...................................................................................... 1 Feature Highlights ...................................................................................................................... 1 Part Names and Functions ...........................................................................
1 OSM and IPM are trademarks of NEC Technologies, Inc. IBM PC/AT, PS/2 and VGA are registered trademarks of International Business Machines Corporation. Apple and Macintosh are registered trademarks of Apple Computer, Inc. Microsoft is a registered trademark of Microsoft Corporation. Windows is a trademark of Microsoft Corporation.
3 Part Names and Functions Front View ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ VIDEO 1/VIDEO 2/RGB 1/RGB 2/PROCEED/EXIT 9 8 7 6 5 4 1 POWER .............................. Press to power the monitor on and off. 2 STANDBY Indicator /POWER ............ Lights green during normal operation. Lights orange when the monitor is in standby mode. 3 Remote Sensor Window ........ Receives infrared signal from the remote control unit. 4 EXIT .........................................
5 Terminal Board 0 OPEN ON B 5 4 3 2 1 10 9 8 7 6 15 14 13 12 11 5 4 3 2 1 10 9 8 7 6 15 14 13 12 11 “ 1 2 3 4 5 6 7 6 7 8 SHORT A OPEN ON “ 1 2 3 4 5 8 SHORT ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ C 0 EXTERNAL CONTROL EXTERNAL CONTROL IN (mini D-SUB 15 PIN).....This terminal is used when power ON/OFF, input selection, AUDIO MUTE and PICTURE MUTE are operated externally (by external control). See also page 41 for external control port pin assignments. NOTE: Select EXT.
7 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ D E 5 4 3 2 1 10 9 8 7 6 15 14 13 12 11 F 5 4 3 2 1 10 9 8 7 6 15 14 13 12 11 D VIDEO 2 VIDEO 2 IN (BNC type).....Connect the video source' s output here. S-VIDEO 2 IN.....Connect the S-video source with an S-connector output here. THROUGH OUT (BNC type).....Connect to a second monitor' s video input to relay the video signal input at VIDEO 2 IN. THROUGH OUT (S-VIDEO).....
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ J H I G G RGB 2 R, G, B, H/CS and V IN (BNC).....These are analog RGB input terminals. Connect external components with R, G, B, H/CS, and V output terminals to these analog RGB input terminals. Be sure that the RGB connection cable is correctly attached to the corresponding terminals. R, G, B, H/CS and V THROUGH OUT (BNC)..... Connect to a second monitor's RGB inputs to relay the RGB signal inputs at R, G, B, H/CS and V IN.
11 Remote Control Unit ON POWER OFF 1 DEGAUSS VIDEO1VIDEO2 RGB1 RGB2 2 ON WIDTH OFF HEIGHT 3 4 5 POSITION/CONTROL SIDE PIN 6 SCAN SELECT NORMAL RASTER CONTROL RGB/VIDEO CONTRAST BRIGHT COLOR VISUAL CONTROL VOLUME ON SCREEN 7 VIDEO TINT SHARPNESS NORMAL MUTE EXIT PROCEED MULTIMEDIA MONITOR RD-336E 1 POWER ON/OFF ................ Press POWER ON to turn the monitor on when the STANDBY/POWER indicator is lit orange.
13 Visual Control 8 RGB/VIDEO CONTRAST ( DEGAUSS VIDEO1VIDEO2 RGB1 OFF HEIGHT H 9 RGB/VIDEO BRIGHT ( / Ä ) .............. Adjusts the overall image and screen brightness. Press and hold for a brighter picture. Press and hold Ä for a darker picture. VIDEO 0 COLOR ( / Ä ) ............... Adjusts color intensity of VIDEO display. Press and hold for more color saturation. Press and hold Ä for less color saturation. VIDEO A TINT ( / Ä ) .................... Adjusts red and green values of VIDEO display.
15 Battery Installation and Replacement The remote control is powered by two 1.5V AA batteries. To install or replace batteries: 1. Turn the remote control unit upside down. 2. Press down on the battery compartment grip and slide the compartment in the direction of the arrow. 3. Install the two new batteries, making sure that their polarity matches the (+) (-) diagrams inside the battery compartment. Incorrect polarity could damage the unit. 4.Close the battery compartment cover.
17 Functions of DIP SW Functions and Settings of DIP SW 1 This DIP switch sets various conditions of the monitor. No.1 No.2 No.3 POWER ON MODE SET No.4 Not Used No.5 ON : On Screen display ON DIP SWITCH MODE DEFEAT VIDEO VIDEO RGB RGB 1 2 1 2 No.1 OFF ON ON ON ON No.2 --OFF ON OFF ON No.3 --OFF OFF ON ON OFF : On Screen display OFF No.6 Not Used No.7 ON : External control ON OFF : External control OFF No.
19 Functions and Settings of DIP SW 2 This DIP switch is used for Sync. Control and Intelligent Power Manager. Set all pins to the OFF position except No. 3 pin during normal operation. No.1 No.2 SYNC. CONTROL MODE AUTO CONTROL (Sep, Comp, Sync on G) No.3 DIP SWITCH No.1 No.2 OFF OFF No.4 No.5 No.
21 Installation External Component Connections Video Signal Connections The NEC PlasmaSync 3300 multimedia monitor is designed for convenient installation with a wide variety of audio, the latest video components and many data processing devices equipped with analog RGB output. VIDEO 1 INPUT Connections 1. Connect the external component video output to VIDEO 1 IN. 2. Connect the external component mono audio or stereo left channel audio output to L AUDIO (MONO). 3.
23 RGB Signal Connections RGB 1 INPUT Connections Mini D-SUB 15 Pin RGB Connector. 1. Connect external components or computers having RGB output to the mini D-SUB 15-Pin connector. 2. Connect the external RGB component mono audio or stereo left channel audio output to L RGB AUDIO IN (MONO). 3. Connect the external RGB component stereo right channel audio output to R RGB AUDIO IN. RGB 2 INPUT Connections Connect external components with R.G.B.H/CS and V output to the R.G.B.
25 Typical Connection Example PlasmaSync 3300 IBM PC OR COMPATIBLES To EXTERNAL CONTROL (mini D-SUB 15 Pin input) EXTERNAL CONTROL To VIDEO IN R, L, inputs To mini D-SUB 15 Pin input CAMERA, VIDEO COPY STAND OR MULTIMEDIA APPLICATION RGB equipment To R,G,B,H/CS and V inputs (BNC) NEC MULTISYNC OR PC-COMPATIBLE MONITOR NOTE: •PlasmaSync 3300 does not support PAL/SECAM on a scan converter. •We do not recommend to use a scan converter for NTSC signal.
27 External Speaker Connections External speakers may be connected to the monitor to reproduce sound from VIDEO 1, VIDEO 2, RGB 1 or RGB 2 signal sources. External speakers may be connected directly to the EXTERNAL SPEAKERS terminals or indirectly by connecting a stereo system amplifier to the audio outputs. CAUTION: Unplug the monitor and all connected components before connecting external speakers. Use only speakers with 8-ohm impedance and a power output rating of 5 watts or more.
29 Controls/Adjustments Power Video Signal Input Settings 1. Plug in the power cord to an electrical outlet to connect power. 2. Press POWER to turn the monitor on. 3. Press POWER again to turn the monitor off. Press the POWER OFF key on the remote control unit to turn the monitor off when the monitor is turned on. The monitor will go into the standby condition and the STANDBY/POWER indicator will light up orange.
31 OSM Controls TM RGB Signal, Picture Adjustments 1. a)Adjust the contrast of RGB display. b)Adjust the brightness of RGB display. 2. Adjust the picture position. See “Signal Identification Flowchart” on pages 43 and 44. NOTE: To reset the stored adjustment data and recall the factory preset data, press the NORMAL key on the remote control unit. NOTE: Over adjusting the POSITION Up/Down may cause a picture to distort. If this happens, readjust the picture so that the distortion is not seen.
33 Accessing OSM Press the PROCEED key. While in the main menu, the keys on the remote control unit work as follows: Turning off OSM Press the EXIT key when in the main menu ; press the EXIT key twice when in submenus. OSM Menus Main Menu On-Screen Manager' s main menu of Controls gives you an overview of the selection of controls available. ON SCREEN MANAGER MAIN MENU OF CONTROLS NOTE: The NORMAL function is not needed in the OSM Turn Off Time, Language Select menus, and Volume Control.
35 Language Select OSM Menus are available in six languages. OSM Location Control You can choose where you would like OSM image to appear on your screen. Selecting OSM location allows you to manually adjust the OSM menu left, right, up, or down. Language Select English Deutsch Français Español Italiano Svenska OSM Location Controls Up Right Left Down POSITION/CONTROL +/- : moves the arrow up or down to select one of the six languages. EXIT : exits to the main menu.
37 Display Mode Display Mode provides you information about the current resolution display and technical data including the horizontal and vertical frequency. RGB Mode H. Freq V. Freq H. Pol V. Pol Neg Pos Source Memory EXIT Display Mode : 640 x 480 : 31.47 kHz : 60 Hz : Neg : Neg : RGB 1 : Factory : : : : : : : : : : Position VIDEO Display Mode Mode H Freq. V Freq. H Pol. V Pol. Source Memory Position Controls The Position controls allow you to adjust the position of the image.
39 Visual Controls The Visual controls allow you to adjust the picture controls such as brightness, contrast, color, tint, sharpness and gamma. Volume Control The Volume control allows you to adjust the volume and balance, or to mute the sound. NOTE: The color, tint, and sharpness controls are not available in the RGB mode and the tint not available in the PAL and SECAM mode.
41 External Control Function External Control Port Pin Assignments 5 4 3 2 Pin No. Signal to be connected 1-3 Not Used 4, 5 INPUT SELECT NO.4 NO.5 INPUT OPEN OPEN VIDEO 1 GND OPEN VIDEO 2 OPEN GND RGB 1 GND GND RGB 2 1 10 9 8 7 6 15 14 13 12 11 OPEN GND - - 6-8 Not Used - - 9 GND - - 10 Power ON/OFF Selection OFF ON 11-14 Not Used - - 15 GND - - NOTE: “GND” means to connect with pin 9. NOTE: If EXT.
43 Signal Identification Flowchart Input signal 28 kHz
45 Troubleshooting Before arranging for service by the NEC Service Center, check the following to be sure repairs are needed. Possible Cause Problem Correction Power cord unplugged. Plug in power cord. Power outlet inactive. Power of external equipment is not ON. Be sure wall switch is on and outlet has power. Switch to ON or connect to an active AC outlet. External equipment has been incorrectly connected. Correct all connections. Incorrect input selection.
47 Specifications Plasma Screen 33 inch Visual size (Diagonal), AC Drive type Phosphor stripe trios Ph 1.05 mm, Pv 1.05 mm Medium-short persistence phosphor Optical filter coating Aspect ratio: 3 : 4 Display color: 260,000 colors (RGB 64 shades of gray respectively) RGB Input Terminals RGB: RGB Output Terminals THROUGH OUT D-SUB 15pin Video Input Terminals VIDEO S-VIDEO Video Output Terminals THROUGH OUT THROUGH OUT (S-VIDEO 1, 2) D-SUB 15pin BNC (R, G, B, H and V) : Video : Analog 0.
49 Maximum Resolution RGB: 640(H) x 480(V) pixels VIDEO: 400 horizontal lines Signal Bandwidth Current Rating 33 MHz (maximum) AC 120 V, 60 Hz Power Consumption 4.5 A (maximum) Dimensions 31.1(W) x 29.1(H) x5.2 (D) inches/ 788(W) x 738(H) x130(D) mm (Height: 24.5 inches/ 620 mm; not including the base) Weight 73.63 lbs/33.4 kg (60.85 lbs/27.
51 Dimensions 52
53 PROFESSIONAL GRAPHICS PRODUCTS Limited Warranty MULTIMEDIA MONITORS NEC Technologies, Inc.(hereafter NECTECH)warrants this product to be free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Parts and labor are warranted for (1) One Year and Plasma display for (1) One year from the date of the first customer purchase. WHO IS PROTECTED This warranty may be enforced only by the first purchaser.
