User’s Manual MultiSync V323
Index DECLARATION OF CONFORMITY ............................................................................................................. English-1 Important Information ................................................................................................................................... English-2 WARNING....................................................................................................................................... English-2 CAUTION ...................................
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: NEC Display Solutions of America, Inc. Address: 500 Park Boulevard, Suite 1100 Itasca, Illinois 60143 Tel. No.
Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET.
• • • • • FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTI-FUNCTION MONITOR: Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions: DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.
Contents Your new MultiSync monitor box* should contain the following: • LCD monitor • Power cord*1 • Video Signal Cable • Wireless Remote Control and AA Batteries • Setup Manual • CD-ROM Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) Power Cord*1 Setup Manual CD-ROM * 1 * Setup Manual Wireless Remote Control and AA Batteries Remember to save your original box and packing material to transport or ship the monitor.
This device cannot be used or installed without the Tabletop Stand or other mounting accessory for support. For proper installation it is strongly recommended to use a trained, NEC authorized service person. Failure to follow NEC standard mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation. Failure to follow these recommendations could result in voiding the warranty.
3. Installing and removing optional table top stand Attaching Mounting Accessories The monitor is designed for use with the VESA mounting system. CAUTION: Installing and removing the stand must be done by two or more people. 1. Attach Mounting Accessories To install, follow those instructions included with the stand or mounting apparatus. Use only those devices recommended by the manufacturer. Be careful to avoid tipping monitor when attaching accessories.
When using the display with the optional table top stand fasten the LCD to a wall using a cord or chain that can support the weight of the monitor in order to prevent the monitor from falling. Fasten the cord or chain to the monitor using the provided clamps and screws. 200 mm Screw Holes Cord or chain Clamp* Screw (M4)* *: included in option stand. Before attaching the LCD monitor to the wall, make sure that the wall can support the weight of the monitor.
Parts Name and Functions Control Panel 쐃 POWER button 쐊 EXIT button Switches the power on/off. See also page 16. Activates the OSD menu when the OSD menu is turned-off. Acts as EXIT button within the OSD to move to previous menu. 쐇 MUTE button Switches the audio mute ON/OFF. 쐎 Remote control sensor and Power Indicator 쐋 INPUT button Acts as SET button within OSD menu. (Toggle switches between [DVI], [DPORT], [VGA], [HDMI], [DVD/HD], [SCART], [VIDEO1], [VIDEO2] or [S-VIDEO]).
English Terminal Panel 쐃 AC IN connector 쐎 VGA IN (mini D-Sub 15 pin) Connects with the supplied power cord. To input analog RGB signals from a personal computer or from other RGB equipment. This input can be used with an RGB, COMPONENT, SCART, VIDEO or S-VIDEO source. Please select signal type in TERMINAL SETTING. See page 25. 쐇 Main Power Switch On/Off switch to turn main power ON/OFF.
Wireless Remote Control 쐏 ASPECT button Selects picture aspect, [FULL], [WIDE], [DYNAMIC], [1:1], [ZOOM] and [NORMAL]. See page 17. 쐄 SOUND button Artificial surround sound for internal/external speakers. Audio out is disabled when surround is set to ON. 쐂 KEYPAD Press buttons to set and change passwords, change channel and set REMOTE ID. 쐆 ENT button*2 쐊 DISPLAY button Turns on/off the information OSD. See page 18. 쐎 MENU button Turns on/off the menu mode. 쐅 AUTO SETUP button Enters auto setup menu.
Operating Range for the Remote Control ON/OFF button: Toggle switches between PIP, POP, PICTURE BY PICTURE-ASPECT and PICTURE BY PICTURE-FULL. See page 22. INPUT button: Selects the “picture in picture” input signal. CHANGE button: Replaces to the main picture and sub picture. Point the top of the remote control toward the LCD monitor’s remote sensor during button operation. Use the remote control within a distance of about 7 m (23 ft.
Setup 1. Determine the installation location NEC recommends the following battery use: CAUTION: Installing your LCD monitor must be done by a qualified technician. Contact your dealer for more information. • Place “AA” size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment. • Do not mix battery brands. • Do not combine new and old batteries. This can shorten battery life or cause liquid leakage of batteries.
When connected with a computer, switch on the power of the computer first. 6. Operate the attached external equipment Display the signal from the desired input source. 7. Adjust the sound Make volume adjustments when required. 8. Adjust the screen (See pages 20 and 21) Make adjustments of the screen display position when necessary. 9. Adjust the image (See page 20) Make adjustments such as backlight or contrast when required. 10.
Connections NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image. NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. Before making connections: * First turn off the power of all the attached equipment and make connections. * Refer to the user manual included with each separate piece of equipment.
Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards with a pixel clock over 162MHz may not display an image correctly. Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically. Resolution 640 x 480 800 x 600 1024 x 768 1280 x 768 1360 x 768 1280 x 1024 1600 x 1200 1920 x 1080 • Scanning frequency Horizontal Vertical 31.5 kHz 60 Hz 37.9 kHz 60 Hz 48.
Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off. NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button on the front of the LCD.
Picture Aspect Mode Power ON Power OFF Power consumption under 0.
Information OSD The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc. Press the DISPLAY button on the remote to bring up the Information OSD. ID number assigned to current monitor*1 ID number assigned monitor to be controlled via RS-232C*2 Input Name Audio input mode Picture aspect Input Signal Information Sub picture information *1: “IR CONTROL” should be set “Primary” or “Secondary”. *2: “IR CONTROL” should be set “Primary”.
NOTE: English OSD (On-Screen-Display) Controls Some functions may not be available depending on the model or optional equipment. Input source Main Menu Icons Main Menu Item 70 50 50 50 50 50 Sub Menu THANK YOU FOR SAVING THE ENVIRONMENT. CARBON FOOTPRINT 86.0 % PICTURE MODE Select Adjustment Settings Goto Adjustment Return Close Key Guide Press UP or DOWN button to select sub-menu. Press SET. Press UP or DOWN, PLUS or MINUS to select the function or setting to be adjusted.
Setting Default PICTURE BACKLIGHT Adjusts the overall image and background brightness. Press + or - to adjust. Note: When AMBIENT1 or AMBIENT2 is selected in picture mode, this function cannot be changed. 70 CONTRAST Adjusts the image brightness in relationship to the input signal. Press + or - to adjust. Note: When sRGB is selected in picture mode, this function cannot be changed. 50 SHARPNESS Adjusts the crispness of the image. Press + or - to adjust.
Adjusts the horizontal size of the image. - Adjusts the vertical size of the image. - VGA input only V RESOLUTION VGA input only INPUT RESOLUTION VGA input only ASPECT If there is a problem with signal detection, this function forces the monitor to display the signal at the desired resolution. After selection, execute “AUTO SETUP” if required. If no problem is detected, the only available option will be “AUTO”. AUTO Select the aspect ratio of the screen image.
TIME Configures the time for the real-time clock. DAYLIGHT SAVING Configures daylight savings on or off. RESET Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER, SCHEDULE SETTINGS and SCHEDULE LIST. OFF - PIP KEEP PIP MODE Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off. When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD. OFF PIP MODE Selects Picture-in-Picture mode. OFF OFF Normal mode.
Selects whether the information OSD is displayed or not. The information OSD will be displayed when the input signal or source changes. The information OSD will also give a warning when there is no-signal or the signal is out-of range. An interval between 3 to 10 seconds for the Information OSD to appear is available. MONITOR INFORMATION Indicates the model and serial number of your monitor. CARBON SAVINGS: Display the estimated carbon saving information in kg-CO2.
LAN SETTING When you use this function, EXTERNAL CONTROL should be “LAN”. NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN SETTING is applied. DISABLE DHCP Enabling this option automatically assigns an IP address to the monitor from your DHCP server. Disabling this option allows you to register the IP address or subnet mask number obtained from your network administrator. NOTE: Consult your network administrator for the IP address when “ENABLE” is selected for [DHCP].
Locks the security password. OFF DDC/CI ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor. ALERT MAIL Selects whether or not to send an e-mail notification of monitor error via wired LAN. RESET Resets the following settings within the DISPLAY PROTECTION menu back to factory setting: FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR, AUTO BRIGHTNESS, DDC/CI. - Selects the method of input detection the monitor uses when more than two input devices are connected.
OVER SCAN Some video formats may require different scanning modes in order to best display the image. ON HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only ON Image size is larger than what can be displayed. The image edge will appear cropped. Approximately 95% of the image will be shown on the screen. OFF Image size stays within the display area. The whole image is displayed on the screen. NOTE: When you use a computer with HDMI out, please set “OFF”.
The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be programmed. To program the schedule: 1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET or the + button to enter the Settings menu. Highlight the desired schedule number and press set. The box next to the number will turn yellow. The schedule can now be programmed. 2.
Remote Control Function REMOTE CONTROL ID FUNCTION Monitor ID:1 Monitor ID:2 Monitor ID:3 Remote works Remote works Remote works REMOTE CONTROL ID The remote control can be used to control up to 100 individual MultiSync monitors using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync monitors.
Monitor ID: Displays the ID number of the current monitor within the daisy chain. Target ID: Displays the ID number of the monitor that to be controlled via daisy chain from the current monitor. Press the “+” or “-” buttons to change the “Target ID” to show the ID number of the monitor to be controlled. To control the entire daisy chained monitors simultaneously, select “ALL” as the “Target ID.” 4. Use the wireless remote controller to control the “SECONDARY” monitor while aiming at the “PRIMARY” monitor.
Controlling the LCD monitor via RS-232C Remote Control This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C” (See page 23). Functions that can be controlled by a personal computer are: • Power ON or OFF. • Switching between input signals. • Sound Mute ON or OFF.
For other commands, please see “External_Control.pdf” file on the CD-ROM.
Controlling the LCD monitor via LAN Control Connecting to a Network Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function. NOTE: When you use this function, EXTERNAL CONTROL should be “LAN” (See page 23). To use a LAN connection, you are required to assign an IP address. Example of LAN connection: Server NOTE: Use a category 5 or higher LAN cable.
Connect the monitor to a commercially available LAN cable before engaging in browser operations. Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be displayed depending on the effectiveness of the cache, and the contents set from the browser may not be reflected in operation.
Alert Mail Setting http:///lanconfig.html This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification will be sent when an error occurs in the monitor. Alert Mail Checking [ENABLE] will turn on the Alert Mail feature. Checking [DISABLE] will turn off the Alert Mail feature. Host Name Type in the hostname of the network connected to the monitor. Up to 60 alphanumeric characters can be used.
Error number * ErrorCode 70h ~ 7Fh 80h ~ Fh 90h ~ 9Fh A0h ~ AFh Alert mail Message The monitor’s power supply is not functioning normally. The cooling fan has stopped. The monitor’s back light unit is not functioning normally. The monitor is overheated. A2h B0h ~ BFh C0h ~ CFh The monitor doesn’t have the input signal. The monitor caused the problem of the abnormal of option board. Explanation Measure Standby power Abnormal Please contact your supplier.
CRESTRON Setting Click “CRESTRON” on the left side of HOME. CRESTRON ROOMVIEW compatibility The monitor supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and controlled from a computer or a controller. For more information, visit http://www.crestron.com ROOMVIEW ROOMVIEW for managing from the computer. ON: Enables ROOMVIEW. OFF: Disables ROOMVIEW. CRESTRON CONTROL CRESTRON CONTROL for managing from the controller. ON: Enables CRESTRON CONTROL.
Reduced Footprint: Provides the ideal solution for environments with superior image quality. Color Control Systems: Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards. OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments via six axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available.
Troubleshooting • The display card should be completely seated in its slot. RED LED on monitor is blinking • A certain failure might have occurred, please contact your nearest authorized NEC DISPLAY SOLUTIONS service facility. • Check the main Power Switch, it should be in the ON position. • • Front Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used.
English Specifications Product Specifications LCD Module Pixel Pitch: Resolution: Color: Brightness: Contrast Ratio: Viewing Angle: Frequency 31.5”/801.3 mm diagonal 0.36375 mm 1920 x 1080 Over 16 million colors (depending on video card used) 450 cd/m2 (Max.), 320 cd/m2 (Factory setting Typ.) @25°C 1300:1 89° (typ) @ CR>10 Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input) 31.5 kHz - 91.1 kHz (Digital Input) Vertical: 50.0 - 85.0 Hz Pixel Clock 25.2 MHz - 162.0 MHz Viewable Size 698.
Pin Assignment 1) Analog multi input (MiniDsub15p): VGA, DVD/HD, SCART, VIDEO2, S-VIDEO Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Name Red, DVD/HD_Pr, S-VIDEO_C Green, DVD/HD_Y, S-VIDEO_Y, VIDEO2 Blue, DVD/HD_Pb GND DDC-GND Red-GND Green-GND Blue-GND +5V (DDC) Mini D-SUB 15P 1 5 6 10 11 15 SYNC-GND GND (B-SYNC) DDC-SDA H-SYNC V-SYNC DDC-SCL 2) RS-232C input/output Pin No 1 2 3 4 5 6 7 8 9 Name NC RXD TXD NC GND NC NC NC NC D-SUB 9P 5 1 6 9 This LCD monitor uses RXD, TXD and GND lines for RS-232C
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).
