Installation and Setup Guide

ManualsBrandsNEC ManualsVideo Wall SolutionNEC X554UNS-TMX4P

NEC Display Solutions of America, Inc.

QIG-TMX4P-554UNS

X554UN-TMX4P, X554UNS-TMX4P Rev 1.1

Parts List

o (4) X554UN or X554UNS Displays

o (4) Onsite Service Warranties (ONSITEMN-3Y-16 or ONSITEMN-3Y-17)

o (4) Peerless Pullout Wall Mounts (DS-VW765-L40)

o (1) 25ft Cat5e Patch Cable

o (4) 3m DisplayPort 1.2 Cables

o (1) IR/Remote Control Kit (KT-RC2)

o (2) Overframe Bezel Kits (KT-55UN-OF or KT-55UN-OF2)

o (2) Tripp Lite 6 Outlet Strip (ISOBar6)

o (1) Display Wall Calibrator Kit (KT-LFD-CC)

NOTES:

o Any walls that this video wall solution is anchored to must be strong enough to support the displays and the

installation must be in accordance with any local building codes. All mounting apparatuses must make secure

contact to wooden studs.

o Please read entire document before starting installation

Summary of content (6 pages)

PAGE 1
NEC Display Solutions of America, Inc. QIG-TMX4P-554UNS X554UN-TMX4P, X554UNS-TMX4P Rev 1.1 Parts List o o o o o o o o o (4) X554UN or X554UNS Displays (4) Onsite Service Warranties (ONSITEMN-3Y-16 or ONSITEMN-3Y-17) (4) Peerless Pullout Wall Mounts (DS-VW765-L40) (1) 25ft Cat5e Patch Cable (4) 3m DisplayPort 1.
PAGE 2
NEC Display Solutions of America, Inc. QIG-TMX4P-554UNS X554UN-TMX4P, X554UNS-TMX4P Rev 1.1 1. For mounting information, please refer to Installation Instructions provided by Peerless Industries, Inc. inside the box of the DS-VW765-L40. 2. Connect the NEC display using the provided DisplayPort cables. Please note that in the picture below, the IN connection is on the left and circled in red while the OUT connection is on the right and circled in blue. 3.
PAGE 3
NEC Display Solutions of America, Inc. QIG-TMX4P-554UNS X554UN-TMX4P, X554UNS-TMX4P Rev 1.1 5. Screw the IR Receiver (KT-RC2) directly to the outside of the video wall and plug it directly into the IR In terminal of Display 1 as shown below. 6. Power up all of the displays and make sure that the LAN power is on for each display. This can be found in the External Control menu. Note that LAN power is OFF out of the box so this will need to be changed for each display within the wall. 7.
PAGE 4
NEC Display Solutions of America, Inc. QIG-TMX4P-554UNS X554UN-TMX4P, X554UNS-TMX4P Rev 1.1 If the control setup is as pictured below, each display does not need a unique IP address assigned to still control each individual monitor. Note that a unique IP address is not necessary to communicate to all displays if display 1 is not connected to a network.
PAGE 5
NEC Display Solutions of America, Inc. QIG-TMX4P-554UNS X554UN-TMX4P, X554UNS-TMX4P Rev 1.1 8. If display 1 is connected to a network or LAN is going into display 1, like the picture below, each display will need a unique IP address to ensure that communication can successfully go through the daisy chain from screen to screen. 9. Ensure that video source is connected to the DisplayPort In interface of display 1. Make sure that all displays are on the DisplayPort input.
PAGE 6
NEC Display Solutions of America, Inc. QIG-TMX4P-554UNS X554UN-TMX4P, X554UNS-TMX4P Rev 1.1 source is connected into display 1 and everything is daisy chained properly, each display should be showing the same image. 10. Go into the Multi-DSP menu to activate Auto Tile Matrix Setup as seen in the picture below. Note that you will need to set the horizontal and vertical monitor dimensions before you activate the Auto Tile Matrix.