Wireless Space Count Manual SENSIT 2009-11-23 This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no license under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher. © Nedap IDEAS, P.O.
Wireless Space Count: SENSIT CONTENTS 1 INTRODUCTION..............................................................................................................................3 1.1 2 INSTALLATION SENSIT ..................................................................................................................4 2.1 2.2 2.3 2.4 3 SAFETY PRECAUTIONS........................................................................................... 4 DIMENSIONS............................................
Wireless Space Count: SENSIT 1 INTRODUCTION The Wireless Space Count system facilitates accurate measurement on occupancy of individual parking spaces in car parks, and on-street parking spaces. This information can be used to guide traffic to free parking spaces but can also be used for on-street parking enforcement and overstay detection. For onstreet enforcement the number of occupied parking spaces can be compared with the number of payments realized by the pay station.
Wireless Space Count: SENSIT 2 INSTALLATION SENSIT 2.1 SAFETY PRECAUTIONS The following safety precautions should be observed during normal use, service and repair. • The SENSIT may only be installed and serviced by qualified service personnel. • To be sure of safety, do not modify or add anything to the SENSIT other than mentioned in this manual or indicated by NEDAP N.V. 2.2 DIMENSIONS The SENSIT is designed for mounting into the floor of a parking space.
Wireless Space Count: SENSIT 2.4 MOUNTING PROCEDURE SENSITS Below the mounting procedure for the SENSIT. Step 1: Distribute the SENSIT over the empty parking lot (without mounting them into the floor). Step 2: All SENSIT are set to transport/stock mode during shipment. Prior to installation all SENSIT must be swept with a strong magnet. This will give the SENSIT a reset. Please ensure to use a strong magnet (Neodymium). Note: Once out of the transport/stock mode the battery lifetime starts to count.
Wireless Space Count: SENSIT Step 8: After installation the SENSIT must be calibrated with no car on top of the sensor or on neighbouring parking bays. Note: When the SENSIT are not calibrated they hardly send any messages. This is due to the fact that there are no events generated because the magnetic tressholds are not crossed. Figure 6: Finished SENSIT installation © Nedap IDEAS, P.O.
Wireless Space Count: SENSIT 3 PROJECT SUPPORT Based on our thorough project analysis including configuration and installation advice we can offer the customer the best AVI solution. 3.1 SITE SURVEY & INSTALLATION ADVICE This will consist of an engineer visiting the site to visually inspect and analyze the location. We will then carry out calculations and provide you with detailed configuration and installation advice for the Wireless Space Count equipment for a specific project. 3.
Wireless Space Count: SENSIT 4 FCC AND IC DECLARATION 4.1 Compliance statements (part15.19) This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operating is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 4.2 Warning (part15.
Wireless Space Count: SENSIT 5 TECHNICAL SPECIFICATIONS SENSIT (EU) 9889019 Operating frequency 868.2 MHz CE compliant EN 60950-1 EN50357 and EN 50364 EN 301 4889-1 V1.6.1 and EN 301 489-3 V1.4.1 EN 61000-6.1, EN 61000-6-2 and 61000-6-3 EN 55011 Class B EN 61204-3 EN 300-220-1 ERV REC 70-03 Dimensions Ø 80 mm (3.15 inch) and 70 mm (2.8 inch) Weight 365 g (12.
Wireless Space Count: SENSIT A PART NUMBERS SENSIT SENSIT (EU) part number: 9889019 SENSIT (US) part number: 9898760 For full product information visit www.nedapavi.com © Nedap IDEAS, P.O.
