Smart Deactivator Manual UL manual smart deactivator according to ul regulations • • • SMART DEAC Mounting SMART DEAC Wiring Appendix 1 : Quick Reference
Technical Support Email: support-eas@nedap.com Postal address: N.V. Nederlandsche Apparatenfabriek “NEDAP”, Parallelweg 2, 7141DC, Groenlo, The Netherlands Safety precautions: CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED NEDAP SERVICE PERSONNEL.
Table of content 1 Introduction 4 2 System overview 5 3 Installation instructions 6 4 Regulatory declaration 7 5 Specifications SMART DEAC 8 6 Appendix 1 9 3
1 Introduction N.V. Nederlandsche Apparatenfabriek “Nedap”, hereafter called “Nedap”, is manufacturer of one of the most reliable and scalable EAS Systems in the market today. With a Nedap EAS system you are able to reduce shoplifting costs to a minimum in combination with Nedap’s tagging solutions. The Nedap Smart Deactivator, also called SMART DEAC, is meant for deactivation of disposable 8.2MHz RF labels.
2 System overview 1 Power Adapter Nedap Part.no.: 9651802 Antenna Model: SDA-265x265 Nedap Part.no.: 9564101 or Model: DAPL-275x275 Nedap Part.no.: 9911537 SMART DEAC 4 RS485 communication 5 Input Nedap Part.no. 9937676 6 Output 7 2 LED Nedap Part.no.: 9563652 Figure 1 Functional system overview The SMART DEAC system (Figure 1) consists of the following components: 1. AC/DC Power adapter Wall Mount 100 – 240 VAC / 12 VDC Nedap Part.no.: (9551802) 2. Smart Deactivator electronics (9937676) 3.
3 Installation instructions The SMART DEAC electronics unit must be powered with a NEC class2 type power source like the NEDAP AC/DC power adapter 100~240Vac/12V dc NEDAP part number 9651802. Always place the unit near a power outlet (less than 1 meter / 3.3 feet ), the power outlet should be easily accessible, also after installation. All the outputs from the SMART DEAC are NEC class2 outputs, output voltages will be 12Vdc or less. The inputs may only be connected to class2 powered system.
4 Regulatory declaration Compliance statements (part15.19) This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Warning (part15.
5 Specifications SMART DEAC Enviromental Description Material Construction Protection Class Aluminium IP20 Min. Operating frequency 7.5 MHz Operational temperature 0 ºC / 32 °F Storage temperature -10 ºC / 14 °F Relative Humidity 20 % Operating Distance Typical 8.2 MHz Max. 8.8 MHz 40 ºC / 104 °F +70 ºC / 158 °F 90 % 0.3 m / 12” Condition non-condensing Tag-dependant Input Requirements and electrical specifications Description Input Voltage Input Current Line Frequency Operation Voltage Power Min.
6 Appendix 1 Deactivator Antenna 265x265 Deactivator Antenna 265 x 265 (cable length 1600 mm) 01 02 Bottom mount Table 150 265 4,5 (4x) 150 150 4,5 (4x) 265 4x , not included 265 150 265 GROENLO THE NETHERLANDS dsgn : CB date : 27 February 2014 12:08 PM rev :A quick reference : antenna 265x265 article no : 9741704 Copyright © by N.V. Nederlandsche Apparatenfabriek NEDAP.
Smart Deactivator 1x Smart Deactivator including power supply 01 1x Antenna connector set 1x Power Supply 02 Mount housing to solid surface 1x Connector cover Connect deactivator antenna to antenna connector to deactivator antenna 106 ANT1 25 10 14.5 ANT GND GND Antenna wire 2 Ground Ground ANT Antenna wire 1 03 Connect deactivator antenna to Smart Deactivator 4.5 131.6 175.3 109.8 40.5 Tie Wrap ANT2 56 86.
LED Output Connector + LED Output Connector - Output Common Normal Open Input Anode Input Kathode + RS485 Connector A RS485 Connector B - LED + LED - Out C Out NO Inp A Inp K +12V RS485 A RS485 B GND It is possible, by using a special RS485 converter and software, to adjust some settings. 5 - 12V Solid State Output 12 11 10 9 8 7 6 5 4 3 2 after 10 seconds of detection (Software > 6.
2014 - v1 parallelweg 2d nl-7141 dc groenlo the netherlands t +31 (0) 544 471555 f +31 (0) 544 465814 e info-rs@nedap.com i www.nedap-retail.
