User Manual

ManualsBrandsNederlandsche Apparatenfabriek NEDAP ManualsElectronicsASSY T325R RF+MD

ASSY T325R RF IR

in any form or by any means, or stored in a data base or retrieval system without the prior written permission of NEDAP.

item

date

revision

dsgn

document

Quick reference : ASSY T325R RF IR

: 15 September 2017 10:41 AM

: CvdB

: A.02

: T9565795-45.01

: 9565795

N.V. Nederlandsche Apparatenfabriek “Nedap”

Parallelweg 2, NL-7141 DC Groenlo (The Netherlands)

Mail: support-retail@nedap.com

1x | ASSY T325R RF

dimensions

2x | lter 2x | connector RJ454x | insullation ring

325mm

1'0.80"

322mm

1'0.68"

1534.3mm

5'0.41"

328.6mm

1'0.94"

1378.3mm

4'6.26"

(Customer counter)

20mm

0.79in

231.7mm

9.12in

97.7mm

3.85in

60mm

2.36in

277,5mm

10.93in

Mounting holes

Use M10-studs

This equipment should be installed, operated, serviced, and repaired by qualied personnel only. The installation and interconnection of this equipment to facility wiring and other

equipment must be done by a competent, qualied craftsperson who is familiar with applicable standards and codes governing the installation. Installation methods, practices, or

procedures that are unauthorised or done improperly are dangerous and could result in serious personal injury or damage to property and equipment.

conduit or slit

(topview)

Warning

Preliminary

Summary of content (8 pages)

PAGE 1
ASSY T325R RF IR 4x | insullation ring 1x | ASSY T325R RF 2x | filter 2x | connector RJ45 Warning This equipment should be installed, operated, serviced, and repaired by qualified personnel only. The installation and interconnection of this equipment to facility wiring and other equipment must be done by a competent, qualified craftsperson who is familiar with applicable standards and codes governing the installation.
PAGE 2
drill the hole Øø 13 mm/(Ø 0.5in) 13mm ø 0.5” 2 1 Drill the hole 2 Clean the hole 3 Insert Hilti-hit 4 Place the nut always use a nylon insulation ring 1 22 1 Nut M10 (not included in installation set) 2 Retainer ring M10 (not included in installation set) 3 Nylon insulation ring M10 (included in installation set) remove covers 1 1 1 4 3 9090mm mm (3.5in) / 3.
PAGE 3
place near to a wallsocket (RF) distance to the wall (RF) >>20 (7.9in) 20cm cm (7.9 in.) distance to a normal door or sliding door (RF) > 40 cm (15.8in) > 40 cm (15.8 in.) distance to roller shutter (RF) > 70 (27.6in) > 70cm cm (27.6 in.
PAGE 4
cabling Rx Tx 1 Instal orient lation ation: Stor Sale e exit (E s fl AS) Stoc oor (SRSF  kroo m (G )  R)  1 Ethernet cable 2 Renos side   IN p revio u    2 Sale s Stoc floor (EA kr Load oom (S S) RSF ing b ay (G ) R) OUT s next filters 3 2 Filter 2 Renos network IN 3 Renos network OUT P.I. > network OUT 1 1 1 1 2 power system Plug the Power Inserter into the socket.
PAGE 5
place keyswitch (optional) 3 1 1 Remove cover 2 Push to remove small metal part 3 Place keyswitch (can be placed on both sides of the antenna) 2 place covers 1 1 1 Screw M3x10 label information 1 1 Pull to see the label information (Two labels at the front side and one at the back side)
PAGE 6
network setup When on the “network setup” -step of the installation wizard, determine the position of the network and decide how to connect to the !Sense network. 1 2 3 1 Network to Power Inserter IN 2 Network to last Renos OUT 3 Network to USB-Network adapter (in any gate) Renos 1 50Ω Connect to the 50Ω PCB from the antenna. 2 Lights / IR Connect to the lights and customer counting. 3 Add-on Provide power and synchronisation to add-ons, like the RFID reader.
PAGE 7
Disclaimer Nedap intends to make this manual accurate and complete. However, Nedap does not warrant that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. Nedap disclaims any liability for damage to property or personal injury resulting, in whole or in part, from improper installation, modification, use or misuse of its products.
PAGE 8