Operation Manual

9
Before using the appliance for the first time
Once your new appliance has been connected, ™…„ appears
in the temperature display. Before you can use your appliance,
you must make a few settings:
■ Set the water hardness range
■ Calibrate the altitude
■ Set the clock
■ Clean the appliance before using it for the first time
Note: You can correct these settings at any time. For
information about changing the water hardness range and the
altitude difference, see chapter: Changing the basic settings;
and for information about setting the clock, see chapter:
Electronic clock.
Setting the water hardness range
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
The water hardness “hard“ (
™…„) is the default setting. Change
the setting if the water is softer.
You can determine the water hardness with the test strips
supplied or ask your water supplier.
Notes
■ If your water is very hard, we recommend that you use
softened water.
■ If you use only softened water, you can, in this case, set your
appliance to the softened water hardness range.
■ If you use mineral water, then set the water hardness range to
hard.
■ If you use mineral water, then it must be non-carbonated (see
chapter: Filling and emptying the water tank).
1. Use the temperature selector to set the water hardness
range.
2. Press and hold the ± info button for 3 seconds.
Your setting is saved.
™†‚ appears in the temperature
display.
Calibrating the altitude
The altitude difference range “0 - 300m“ (™†‚) is the default
setting. Change this setting if the location of the appliance is
higher or lower than this.
1. Use the temperature selector to set the altitude difference
range.
2. Press and hold the ± info button for 3 seconds.
Your setting is saved.
Setting the clock
Note: When you press the KJ clock function button, you have
3 seconds to set the clock using the rotary selector. Should this
have been insufficient for you, you can amend the clock time
later.
‹:‹‹ flashes in the clock display.
1. Briefly press the KJ clock function button to go to the
setting mode.
The
KJ and 3 symbols light up. ‚ƒ:‹‹ appears in the
clock display.
2. Set the current time using the rotary selector.
Your setting is accepted after 3 seconds.
Changing the clock
To subsequently change the time, press the
KJclock function
button repeatedly until the
KJ and 3 symbols light up again.
Change the time with the rotary selector.
Cleaning the appliance
Clean your appliance before using it for the first time.
1. Remove the accessories from the cooking compartment.
2. Completely remove any residual packaging (e.g. chips of
polystyrene) from the cooking compartment.
3. Clean the accessories and cooking compartment with hot
soapy water (see section: Cleaning and care).
4. Fill the water tank with 400 ml water (see section: Filling and
emptying the water tank).
5. Slide in the water tank all the way.
6. Switch on the appliance. To do this, press the operating
mode selector so that it pops out.
The appliance is then ready for use.
7. Using the operating mode selector, set % Top/bottom heat
(see section: Operating the appliance).
Water hardness range Setting symbol (temperature dis-
play)
softened
™…‹
soft
™…‚
medium
™…ƒ
hard
™…„
Altitude difference
range
Setting symbol (temperature dis-
play)
Under 0m
™†‹
0 - 300m
™†‚
300 - 600m
™†ƒ
600 - 900m
™†„
900 - 1200m
™†…
1200 - 1500m
™††
1500 - 1800m
™†‡
1800 - 2100m
™†ˆ
2100 - 2400m
™†‰
above 2400m
™†Š
Altitude difference
range
Setting symbol (temperature dis-
play)