Operation Manual

36
Keeping the appliance clean
To avoid getting the cooking compartment dirty,
■ clean the cooking compartment after each use, as dirt will
bake on the next time it is heated up, and this can only be
removed with difficulty
■ always remove flecks of limescale, grease, starch and
albumin (e.g. egg white) immediately
■ use 3 CircoTherm® whenever possible. This operating
mode creates less dirt
■ Use the universal pan to bake very moist cakes
■ use suitable ovenware when roasting (e.g. roasting dish) or a
roasting sheet (see section: Accessories)
Descaling
You can descale your appliance at any time. However, you
must descale the appliance at regular intervals. Otherwise, you
will not be able to continue cooking using steam. The lit
Í symbol reminds you to do this.
After starting steam-assisted operation, the
Í symbol lights up
and "No. of uses until descaling required 5" appears for a short
time in the text display. This number tells you how many steam-
assisted operations (e.g. 5) you can still run before you must
descale your appliance. You can therefore prepare for the
descaling in good time.
The descaling programme (duration approx. 40 minutes)
consists of the following sequences:
■ Descaling
■ 1st rinse
■ 2nd rinse
For hygiene reasons, the descaling programme must be run
through completely so that the appliance can be ready for
operation again. It cannot be interrupted using the „ Stop
button.
If the descaling process is interrupted (for example, due to a
power failure or because the appliance is switched off), you are
prompted to continue with the descaling programme after the
appliance is switched back on. The programme continues by
repeating the interrupted process (for example, 1st rinse).
Caution!
■ Damage to the appliance: Only use the descaling tablets
that are recommended by us to descale the appliance. Other
descalers may damage the appliance.
Ordering descaling tablets through after-sales service:
Product no. 310967
Ordering descaling tablets through the retail trade: Product
no. TZ60002
■ Risk of surface damage: Do not allow descaling solution to
come into contact with the control panel or other sensitive
surfaces. If this does happen, remove the descaling solution
immediately with water.
Start the descaling programme.
The descaling programme can only be started once the
cooking compartment has completely cooled down. There must
be no residual heat (
œ or •) shown in the display.
If you have cooked using steam immediately before descaling,
you must first switch the appliance off so that the residual water
is pumped out of the evaporator system.
1. Dissolve the descaling tablets in water to make a descaling
solution.
Note: Follow the manufacturer's instructions for the descaling
tablets.
2. Switch on the appliance.
3. Press and hold the Í descaling button for 3 seconds.
"Pour descaling solution into tank and press Start button" and
š†™ are displayed.
4. Fill the water tank with 400 ml of descaling solution and slide
it in fully. Dispose of the rest of the descaling solution and
rinse with water.
5. Press the ƒ Start button.
The
ƒ symbol lights up The descaling starts.
Notes
■ If the water tank has not been filled, a signal sounds and the
Descale programme does not start. Fill the water tank with
the descaling solution and slide it in fully.
■ If a signal sounds and the ƒ symbol flashes, this indicates
that the
ƒ Start button has not been pressed. Press the
ƒ Start button.
■ The clock display shows how long the Descale programme
has left to run.
1st rinse
After the descaling is complete, a signal sounds and "Empty
tank and refill with fresh water" is displayed in the text display.
1. Empty the water tank, rinse it out thoroughly and fill it with
400 ml fresh water.
2. Slide in the water tank all the way.
"1st rinse" and
§ü‚ are displayed (rinsing1 = 1st rinse). The
ƒ symbol flashes.
3. Press the ƒ Start button.
The
ƒ symbol lights up The appliance starts rinsing.
After the 1st rinse is complete, a signal sounds and "Empty
tank and refill with fresh water" is displayed in the text display.
2nd rinse
1. Empty the water tank, thoroughly rinse it and fill it with 400 ml
fresh water.
2. Slide in the water tank all the way.
"2nd rinse" and
§ü ƒ are displayed (rinsing2 = 2nd rinse). The
ƒ symbol flashes.
3. Press the ƒ Start button.
The
ƒ symbol lights up The appliance starts rinsing.
After the 2nd rinse is complete, a signal sounds and "Empty
tank and clean" and "Descaling complete" are displayed in the
text display.
Removing the remaining water
1. Empty and thoroughly rinse out the water tank.
2. Switch off the appliance.
Self-cleaning surface
The back wall of the cooking compartment is coated with self-
cleaning enamel. This coating absorbs and disintegrates
splashes from baking and roasting while the oven is in
operation.
Large splashes only disappear after the oven has been used
several times.
Discolouration on the rear wall does not affect the self-cleaning
function.
Caution!
Damage to surfaces on self-cleaning areas due to applying
oven cleaner.Never clean the self-cleaning surfaces with oven
cleaner.
If oven cleaner accidentally gets onto self-cleaning surfaces,
remove it immediately with a sponge and plenty of water.
Caution!
Damage to surfaces on self-cleaning areas due to the use of
abrasive and acidic cleaning agents and aids.
Do not use cleaning agents containing abrasive substances or
acids.
Do not use abrasive cleaning aids such as steel wool or
scourers.