Assembly & Installation Instructions
Table Of Contents
- Extractor hood
- en
- Table of contents
- 1 Safety
- 2 Avoiding material damage
- 3 Environmental protection and saving energy
- 4 Operating modes
- 5 Familiarising yourself with your appliance
- 6 Accessories
- 7 Basic operation
- 8 Cleaning and servicing
- 9 Troubleshooting
- 10 Disposal
- 11 Customer Service
- 12 Installation instructions
- 12.1 Scope of delivery
- 12.2 Appliance dimensions
- 12.3 Safety clearances
- 12.4 Secure installation
- 12.5 General information
- 12.6 Instructions for the electrical connection
- 12.7 Information on the installation situation
- 12.8 Instructions for the exhaust air pipe
- 12.9 Instructions for the air extraction mode
- 12.10 Information about circulating-air mode
- 12.11 Installation
- 12.11.1 Checking the unit
- 12.11.2 Preparing the units
- 12.11.3 Preparing the appliance
- 12.11.4 Preparing circulating-air mode
- 12.11.5 Installing the appliance
- 12.11.6 Establishing the exhaust air connection
- 12.11.7 Establishing the connection for the circulated air
- 12.11.8 Connecting to the power supply
- 12.11.9 Removing the appliance
Operating modes en
5
3.2 Saving energy
If you follow these instructions, your appliance will use
less power.
Adjust the fan speed to the amount of steam pro-
duced during cooking.
¡
The lower the fan speed, the less energy is con-
sumed.
Only use the intensive mode as required.
If cooking produces large amounts of steam, select a
higher fan speed in good time.
¡
The odours are distributed around the room less.
Switch off the lighting if it is no longer required.
¡
When the lighting is switched off, it does not con-
sume any energy.
Clean or replace the filters at regular intervals.
¡
The effectiveness of the filter is retained.
Put the cooking lid on.
¡
The cooking vapours and condensation are re-
duced.
Only use the additional functions if required.
¡
Switching off additional functions reduces power
consumption.
4 Operating modes
You can use your appliance in air extraction mode or
circulating-air mode.
4.1 Air extraction mode
The air which is drawn in is cleaned by the grease fil-
ters and conveyed to the exterior by a pipe system.
The air must not be discharged into a
flue that is used for exhausting fumes
from appliances burning gas or other
fuels (not applicable to appliances that
only discharge the air back into the
room).
¡ If the exhaust air is to be conveyed
into a non-functioning smoke or ex-
haust gas flue, you must obtain the
consent of the heating engineer re-
sponsible.
¡ If the exhaust air is conveyed
through the external wall, a tele-
scopic duct should be used.
4.2 Air recirculation mode
The air which is drawn in is cleaned by the grease fil-
ters and an odour filter, and conveyed back into the
room.
To bind odours in circulating-air mode,
you must install an odour filter. The dif-
ferent options for operating the appli-
ance in circulating-air mode can be
found in our catalogue. Alternatively,
ask your dealer. The required accessor-
ies are available from specialist retail-
ers, from customer service or from the
Online Shop.
5 Familiarising yourself with your appliance
5.1 Controls
The controls are used to configure all functions of your
appliance and to obtain information about the operat-
ing status.
Switch off the appliance
or switch on fan setting 1
Switches fan setting 2 on.
Switch on fan level3 or
intensive mode.
Switch the lighting on or
off.