Operating/installations instructions
Table Of Contents
- [en] Instructions for installation and use
- Ú Table of contents
- [en] Instructions for installation and use
- 8 Intended use
- ( Important safety information
- 7 Environmental protection
- Ç Operating modes
- 1 Operating the appliance
- Operating the appliance
- Note:
- Control panel model 1
- Setting the fan
- Intensive setting
- Fan run-on time
- AirFresh function
- Lighting
- Saturation display
- Audible signal
- Control panel model 2
- Setting the fan
- Intensive setting
- Fan run-on time
- AirFresh function
- Noise reduction function
- Lighting
- Saturation display
- Audible signal
- 2 Cleaning and maintenance
- 3 Trouble shooting
- 4 Customer service
- ( Important safety information
- K General information
- 5 Installation
- Installation
- Preparing the installation
- Installation
- Attaching and aligning the appliance
- 1. First, remove the protective foil from the back of the appliance and, following installation, remove the foil completely.
- 2. When attaching the appliance, ensure that it engages firmly with the brackets. «
- 3. Align the appliance horizontally by turning the brackets. If required, the appliance can be moved to the right or left. ¬
- 4. Firmly tighten the screws for the brackets. When doing so, hold the brackets securely in place. ®
- 5. Firmly tighten the knurled nuts. ¯
- Connecting the pipes
- Attaching the flue duct
en Operating the appliance
6
AirFresh function
Press the - button until 3‚ appears. The fan runs for
approx. five minutes per hour.
If you want to end the AirFresh function, press the #
button.
Lighting
The lighting can be switched on and off independently
of the fan.
Press the A button.
Setting the brightness
Press and hold the A button until the desired
brightness is reached.
Saturation display
When the metal mesh grease filters or the activated
carbon filter are saturated, a signal sounds for approx.
4 seconds after the fan is switched off. In addition, this
symbol is indicated on the display: ª
If you have not yet done so, the metal mesh grease
filters should be cleaned now.
For instructions on how to clean the metal mesh grease
filters, please refer to the section Cleaning and
maintenance
.
While the saturation display is flashing, it can be reset.
To do this, press the – button.
Audible signal
Switching on the acoustic signal
When the fan is switched off, press the # and + at the
same time for approx. three seconds. An
acknowledgement signal sounds.
Switching off the acoustic signal
Repeat the "Switching on the acoustic signal" process.
Control panel model 2
Control panel
Setting the fan
Switching on the appliance
■ Press the # button.
The fan starts at setting ƒ.
■ Press the + or - button to change the fan strength.
Switching off
Press the # button.
Intensive setting
You can use the intensive setting if there is a large
build-up of odours and fumes/vapours.
Press the ˜ button. ˜ƒ appears in the display. Press
the - button to switch back to the intensive setting ˜‚.
After approx. six minutes, the electronics automatically
reduce the fan to a lower setting . If you want to end the
intensive setting before this time expires, press the ˜
button.
Fan run-on time
Press the - button until – appears.
After approx. ten minutes, the fan switches off
automatically.
AirFresh function
Press the - button until 3‚ appears. The fan runs for
approx. five minutes per hour.
If you want to end the AirFresh function, press the #
button.
Noise reduction function
The noise reduction function reduces the fan noise.
Switching on the appliance
Press the 4 button.
The function is possible in all fan settings, except in fan
setting ‚. It also remains active after the fan is switched
off.
Switching off the appliance
Press the 4 button.
Lighting
The lighting can be switched on and off independently
of the fan.
Press the A button.
Setting the brightness
Press and hold the A button until the desired
brightness is reached.
Explanation
#
Fan on/off
4
Noise reduction
- Reduce the fan settings/fan run-on time/interval ventilation
+ Increase the fan settings/intensive setting 1, 2
˜
Direct selection of intensive setting 2
A
Light on/off/dimming
IUHVK
YRO
YRO