User Manual
Table Of Contents
- Your new tumble dryer
- Display rules
- Contentsen Installation and operating instructions
- 8 Intended use 4
- ( Safety instructions 4
- 7 Environmental protection 12
- 5 Installation and connection 13
- ΠDraining the condensation water 15
- Y The main points in brief 17
- * Getting to know your appliance 18
- Z Laundry 21
- / Programmes and buttons 22
- 1 Operating the appliance 25
- M Signal setting 28
- D Cleaning 29
- 3 Faults and what to do about them 31
- J After-sales service 33
- [ Consumption values 34
- J Technical data 35
- 8 Intended use
- ( Safety instructions
- Safety instructions
- Children/people/pets
- Installation
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of electric shock/fire/ material damage/damage to the appliance!
- : Warning
- Risk of fire/material damage/ damage to the appliance!
- : Warning
- Risk of injury/material damage/damage to the appliance!
- : Warning
- Risk of injury!
- Operation
- Cleaning/Maintenance
- 7 Environmental protection
- 5 Installation and connection
- 2. Press the Start button.
- 3. Wait for 5 minutes.
- 4. Empty the condensate container again.
- 5. Switch off the dryer.
- 2. When the dryer is delivered from the factory, the hose for discharging the condensation into the condensation container is fastened to the connecting piece.
- 3. Detach the condensation hose from the socket.
- 4. Place the condensation hose in the "parked" position.
- 5. Take the drain hose from the accessories and secure it to the free connecting piece.
- 6. Fasten the other end of the drain hose with the remaining accessories, depending on the connection situation (A, B or C).
- Buttons in the display panel
- Display panel
- Do not tumble-dry the following fabrics:
- / Programmes and buttons
- 1 Operating the appliance
- 2. Turn the programme selector to any programme to switch the dryer on.
- 3. Close the dryer door.
- 2. Use the programme selector to set the required programme. The default programme settings for the selected programme appear in the display panel.
- 3. If required, adjust the default programme settings. You can find detailed information on this from ~ Page 22 onwards.
- 2. Add or remove laundry.
- 3. Select another programme or an additional function, if required.
- 4. Close the dryer door.
- 5. Press the Start button.
- 2. Turn the programme selector to the "off" position.
- 2. Remove the fluff filter.
- 3. Remove the fluff from the recess in the fluff filter.
- 4. Open the fluff filter and remove all the fluff.
- 5. Rinse away the fluff under running water or clean the fluff filter in the dishwasher.
- 6. Dry the fluff filter, close it and reinsert the fluff filter.
- 2. Pour out the condensation water.
- 3. Push in the condensate container until you feel it lock back into place in the dryer.
- Activating setting mode
- 1. Switch the dryer on.
- 2. Select the "Cottons" programme in position 1 and wait for five seconds.
- 2. The spin speed is shown in the display.
- 3. Press the "Ready in" time button or the drying time button to change the spin speed.
- 4. Turn the programme selector clockwise to position 3.
- 5. The volume of the audible signal at the end of the programme is shown in the display.
- 6. Press the "Ready in" time button or the drying time button to change the volume.
- 7. Turn the programme selector clockwise to position 4.
- 8. The volume for the audible button signal is shown in the display.
- 9. Press the "Ready in" time button or the drying time button to change the volume.
- 2. Open the maintenance flap fully.
- 3. Turn both locking levers towards each other.
- 4. Remove the top cap from the heat exchanger.
- 5. Remove the heat exchanger.
- 6. Flush water through the heat exchanger from all sides to completely remove all fluff.
- 7. Remove all fluff from the seals on the dryer and on the heat exchanger.
- 8. Allow all the water to drip off.
- 9. First insert the heat exchanger, and then fit the heat exchanger's top cap in place.
- 10. Turn both locking levers back and close the maintenance flap until it locks into place.
- 11. Close the maintenance flap and press on it until you feel it click in place.
- Cleaning the moisture sensor
- 3 Faults and what to do about them
- J After-sales service
- [ Consumption values
- 9 kg
- 4.5 kg
- 9 kg
- 4.5 kg
- 1400 rpm
- 129 min
- 69 min
- 4.36 kWh
- 2.31 kWh
- 1000 rpm
- 150 min
- 80 min
- 5.23 kWh
- 2.77 kWh
- 800 rpm
- 181 min
- 91 min
- 6.02 kWh
- 3.19 kWh
- 1400 rpm
- 106 min
- 54 min
- 2.61 kWh
- 1.38 kWh
- 1000 rpm
- 127 min
- 65 min
- 4.01 kWh
- 2.12 kWh
- 800 rpm
- 147 min
- 76 min
- 4.50 kWh
- 2.38 kWh
- 3.5 kg
- 3.5 kg
- 800 rpm
- 46 min
- 1.42 kWh
- 600 rpm
- 56 min
- 1.74 kWh
Installation and connection en
13
5 Installation and
connection
Installation and connection
Scope of delivery
■ Dryer
■ Installation and operating
instructions
■ Basket for woollens
*
■ Condensation drain*
Installing and connecting the
dryer
:Warning
Risk of death!
There is a risk of electric shock as the
dryer is operated with electricity.
■ Check the dryer for visible damage.
You must not operate the dryer if it is
damaged.
■ Before connecting the dryer to the
power supply, ensure that the
electric voltage specified on the
rating plate matches the voltage of
your socket.
■ Only use residual current circuit
breakers with the following symbol:
z.
■ Ensure that the mains cable is not
kinked or trapped and that it does
not come into contact with heat
sources or sharp edges.
:Warning
Children could lock themselves in the
dryer, putting their lives at risk!
Do not set up the dryer behind a door
or sliding door as this may obstruct the
dryer door or prevent it from opening.
Caution!
Risk of injury
■ As the dryer is heavy, you could
injure yourself by trying to lift it.
Do not lift the dryer on your own.
■ You could cut your hands on the
sharp edges of the dryer. Do not
hold the dryer by the sharp edges.
■ Protruding parts on the dryer may
break off when it is lifted or pushed.
Do not move the dryer by holding on
to protruding parts.
Caution!
Risk of material damage to the dryer or
fabrics
■ Check the dryer for damage caused
during transportation. Never operate
a dryer if it is damaged.
■ Any residual water in the dryer may
freeze and damage the dryer. Do not
install the dryer in rooms that are at
risk of frost.
During installation ensure that:
■ The dryer is placed on a clean, level
and firm surface,
■ The mains plug can be accessed at
all times,
■ The air inlet on the dryer is kept clear
and there is sufficient ventilation,
■ The area around the dryer is kept
clean and
■ The dryer is levelled using the
threaded feet.
Note: Check the alignment of the
appliance with a spirit level and
correct if necessary. Change the
height by turning the appliance feet.
All appliance feet must stand firmly
on the ground.
Incorrect alignment may cause high
noise levels, vibrations and improper
movement of the drum.
Note: If in doubt, have the appliance
connected by a specialist.
* Depending on the model